Manuals / Kodak / Computer Equipment / Scanner

Kodak A-61092 manual Replacing the exposure lamps

Models: A-61092

1 118

Download 118 pages 34.53 Kb

Page 48

Replacing the exposure lamps

Replacing the exposure lamps

The exposure system consists of four long-life fluorescent lamps. There are two lamp housings; one upper and one lower. Each lamp housing contains two lamps.

Change the lamps at least every 500 hours, when image quality appears to be degrading (and standard maintenance procedures do not improve the image quality), or when requested to do so by an operator message. Always replace both lamps in a housing at the same time, or exposures may appear inconsistent. Always use the recommended lamps, or image quality may be unacceptable.

1.Turn the side panel switch off.

2.Open the right side access door.

3.Remove the imaging guides. (Refer to the section entitled, “Replacing the imaging guides”.)

4.Grasp the tab at the end of the upper lamp housing and slide the housing out of the track.

Tab

Upper lamp housing

WARNING: Make sure the lamps are cool before attempting to remove them from the lamp housing.

A-61092 September 1999

5-13

Image 48

Kodak A-61092 manual Replacing the exposure lamps

Contents

User’s Guide Document ScannerA-61092 Part No. 1E8133 IMPORTANT Equipment shall be installed by qualified personnel power before installation CAUTION Hot surface, avoid contactWARNING Dangerous voltage. Disconnect the main ATTENTION Eviter le contact, pieces brulantesIMPORTANT Equipment shall be installed by qualified personnel power before installation CAUTION Moving parts, avoid contactWARNING Dangerous voltage. Disconnect the main ATTENTION Eviter le contact, pieces en mouvementScanner features 1 IntroductionScanner options Feed tray - holds documents prior to feeding Rear view Scan mode Mode name/numberindicator indicatorOperating keys and indicators Key/IndicatorFunction Keys/Indicators Operating keys and indicatorsKeys/Indicators FunctionOperating keys and indicators Key/IndicatorClear/Cancel Run NEXT Stop Enter Function2 Getting Started Turning on the scannerSelecting the language display Calibrating the scanner Preparing documents for scanning Unsuccessful calibrationAdjusting the feed and separator roller gap semi-automatic feeder only6. Turn the gap adjustment knob counterclockwise 2 1/2 turns Adjusting the feed shelf position semi automatic feeder onlyAdjusting the feed shelf side guides semi-automatic feeder onlyFeed Shelf Label Adjusting the exit hopper side guides and end stop arrowsside guides Changing the deflector 3 Operating the Scanner OverviewSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents adjustmentGraphic depicts movement lever is usedFeeding documents using the automatic feeder Using function codes 4 Function CodesSetup Function code summaryStatus CountersFootswitch OperationScanning EndorserSuper12 Document Printer Patch ReaderCode Function Code NameDescription Code F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 F39Function Code Name DescriptionCode Function Code NameDescription Enter CodeFunction Code Name DescriptionCode Function Code NameDescription Code Function Code NameDescription 5 Maintenance Cleaning tasks Cleaning materials Replacement partsDaily maintenance procedures Cleaning the imaging guides4. Remove dust from the imaging guides, using a soft bristle brush Cleaning the feed and separator rollers semi- automatic feeder Cleaning the feeder module and separator roller automatic feeder Cleaning the feeder module and separator rollerCleaning the separator roller Cleaning the paper path Vacuuming inside the scanner 1. Open the front cover 2. Raise the horizontal plate 7. Replace the imaging guides Weekly maintenance procedures Cleaning the exposure lamp housingsCleaning the cabinet Monthly maintenance procedures Cleaning the air filterReplacement procedures Replacing the air filterReplacing the exposure lamps 6. Dispose of or recycle the used lamps Replacing the imaging guides Replacing the feeder module and separator roller Replacing the feeder moduleReplacing the separator roller Ordering replacement parts Ordering cleaning materials 6 Operator Messages Operator message listing Operator Message DisplayedDescription/Action Required CodeCode E121 E122 E123 E124 E125 E126 E127 E128 E130 E131 E132 E133 E140 E141Operator Message Displayed Description/Action RequiredCode Operator Message DisplayedDescription/Action Required Code Operator Message DisplayedDescription/Action Required Code Operator Message DisplayedDescription/Action Required Code E500 E501 E502 E503 E512 E513 E550 E551 E552 E553 E562 E563 E504 E505Operator Message Displayed Description/Action Requiredvarious messages various messages various messages various messages CodeOperator Message Displayed Description/Action Required7 Troubleshooting Trouble and remedy chartTrouble Probable CauseTrouble Probable CauseRemedy Clearing the document path The document pathClearing documents The feeder/horizontal transport area The imaging guide area Upper lamp housing assembly Upper imaging guide Lower imaging guideThe lower roller assembly area Vertical baffle handle Baffle plate Lower roller assemblyThe vertical transport area The upper turn area Top cover Baffle plate Upper turn handleThe document exit area Exit handle Exit baffle Static brush Static brush under housing8 Accessories Supplies SupplyCatalog # Imaging Station LampsParts and tools Part/ToolUnited States and Canada Order NumberUsing the Bar Code Reader Bar code types Code TypeCharacter Set Available Characters in SetBar code placement Before you begin Enabling bar code reading Enabling the bar code confirma- tion tonePerforming a bar code test 1. Perform test option 3=%KODAK Using the Evaluate option Static bar code evaluation1. Select 1=EVALUATE 2. Select either 1=Transport Off or 2=Transport OnUsing the Imaging Station Right-side access door8-12 A-61092 September5. Tape the bar code sample section in place Dynamic bar code evaluation Dimensional Fields Pass or Fail Evaluating test resultsReflectance Fields Grades A through F GradeField A PassProblem Type Table 2 - Common Causes of Low Bar Code RatingsCause FieldUsing the Display option Using the %KODAK option1. Select 2=DISPLAY ∙ Bar code was not readUsing the %NORM option The first time the test is run, the two percentages will be the same Using the Check Feeder / Check Stacker Using the check feederClearing jams in the check feeder Cleaning the check feeder Using the check stacker Using the Endorser Die stylesBefore you begin Changing the die drum Top cover2. Push down the locking lever 9. Raise the drum locking lever to secure the die drum assembly Changing the ink roller Setting the date and code number Selecting the Endorser mode Enabling the Endorser Changing the print positionUsing the Footswitch FootswitchEnabling the confirmation tone Footswitch Pressed actions Footswitch PressedAction Footswitch Released actions Footswitch Pressed DefinitionFootswitch Released ActionUsing the Patch Reader Patch typesPatch code placement Before you begin Positioning the Patch ReaderCleaning the Patch Reader Enabling patch reading Enabling the patch code confirmation toneSensor Appendix A Basic Concepts ModesLinked modes Image addresses Using the Next key Assigning an image address∙ Enter Using Function Code F92 Indexing schemes Image address formatsSingle level indexing Two level indexing Pageeach document is defined as follows Three level indexing Page…Three level offset indexing Controlling document level changes DOCUMENT I M A G I N G EASTMAN KODAK COMPANY Document Imaging Rochester, New YorkA-61092 9/99 Eastman Kodak Company Printed in U.S.A Printed on recycled paper