Manuals / Kodak / Computer Equipment / Scanner

Kodak A-61092 Adjusting the feed shelf side guides, semi-automatic feeder only, Feed Shelf Label

Models: A-61092

1 118

Download 118 pages 34.53 Kb

Page 18

Adjusting the feed shelf side guides

Adjusting the feed shelf side guides

(semi-automatic feeder only)

Before you begin processing documents, adjust the side guides on the feed shelf to accommodate the documents being processed.

1.Slide apart the side guides on the feed shelf until the feed shelf label is visible.

Feed shelf label

Side guide

Side guide

Feed shelf

Feed Shelf Label

Center line

2.Center the documents across the feed shelf label. Adjust the feeder side guides dependent upon the width of the document. Leave approximately 1/16 in. (2 mm) clearance on each side of the documents so they feed properly.

NOTE: If the documents are larger than the area shown on the feed shelf label and do not fit between the side guides, rotate and reposition the documents within the side guides.

A-61092 September 1999

2-7

Image 18

Kodak A-61092 manual Adjusting the feed shelf side guides, semi-automatic feeder only, Feed Shelf Label

Contents

User’s Guide Document ScannerA-61092 Part No. 1E8133 WARNING Dangerous voltage. Disconnect the main IMPORTANT Equipment shall be installed by qualified personnelpower before installation CAUTION Hot surface, avoid contact ATTENTION Eviter le contact, pieces brulantesWARNING Dangerous voltage. Disconnect the main IMPORTANT Equipment shall be installed by qualified personnelpower before installation CAUTION Moving parts, avoid contact ATTENTION Eviter le contact, pieces en mouvementScanner features 1 IntroductionScanner options Feed tray - holds documents prior to feeding Rear view indicator Scan modeMode name/number indicatorOperating keys and indicators Key/IndicatorFunction Keys/Indicators Keys/IndicatorsOperating keys and indicators FunctionClear/Cancel Run NEXT Stop Enter Operating keys and indicatorsKey/Indicator Function2 Getting Started Turning on the scannerSelecting the language display Calibrating the scanner Preparing documents for scanning Unsuccessful calibrationAdjusting the feed and separator roller gap semi-automatic feeder only6. Turn the gap adjustment knob counterclockwise 2 1/2 turns Adjusting the feed shelf position semi automatic feeder onlyAdjusting the feed shelf side guides semi-automatic feeder onlyFeed Shelf Label Adjusting the exit hopper side guides and end stop arrowsside guides Changing the deflector 3 Operating the Scanner OverviewSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Graphic depicts movement Feeding thick documentsadjustment lever is usedFeeding documents using the automatic feeder Using function codes 4 Function CodesStatus SetupFunction code summary CountersScanning FootswitchOperation EndorserSuper12 Document Printer Patch ReaderCode Function Code NameDescription Function Code Name CodeF17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 F39 DescriptionCode Function Code NameDescription Function Code Name EnterCode DescriptionCode Function Code NameDescription Code Function Code NameDescription 5 Maintenance Cleaning tasks Cleaning materials Replacement partsDaily maintenance procedures Cleaning the imaging guides4. Remove dust from the imaging guides, using a soft bristle brush Cleaning the feed and separator rollers semi- automatic feeder Cleaning the feeder module and separator roller automatic feeder Cleaning the feeder module and separator rollerCleaning the separator roller Cleaning the paper path Vacuuming inside the scanner 1. Open the front cover 2. Raise the horizontal plate 7. Replace the imaging guides Weekly maintenance procedures Cleaning the exposure lamp housingsCleaning the cabinet Monthly maintenance procedures Cleaning the air filterReplacement procedures Replacing the air filterReplacing the exposure lamps 6. Dispose of or recycle the used lamps Replacing the imaging guides Replacing the feeder module and separator roller Replacing the feeder moduleReplacing the separator roller Ordering replacement parts Ordering cleaning materials 6 Operator Messages Description/Action Required Operator message listingOperator Message Displayed CodeOperator Message Displayed CodeE121 E122 E123 E124 E125 E126 E127 E128 E130 E131 E132 E133 E140 E141 Description/Action RequiredCode Operator Message DisplayedDescription/Action Required Code Operator Message DisplayedDescription/Action Required Code Operator Message DisplayedDescription/Action Required Operator Message Displayed CodeE500 E501 E502 E503 E512 E513 E550 E551 E552 E553 E562 E563 E504 E505 Description/Action RequiredOperator Message Displayed various messages various messages various messages various messagesCode Description/Action RequiredTrouble 7 TroubleshootingTrouble and remedy chart Probable CauseTrouble Probable CauseRemedy Clearing the document path The document pathClearing documents The feeder/horizontal transport area The imaging guide area Upper lamp housing assembly Upper imaging guide Lower imaging guideThe lower roller assembly area Vertical baffle handle Baffle plate Lower roller assemblyThe vertical transport area The upper turn area Top cover Baffle plate Upper turn handleThe document exit area Exit handle Exit baffle Static brush Static brush under housing8 Accessories Catalog # SuppliesSupply Imaging Station LampsUnited States and Canada Parts and toolsPart/Tool Order NumberUsing the Bar Code Reader Character Set Bar code typesCode Type Available Characters in SetBar code placement Before you begin Enabling bar code reading Enabling the bar code confirma- tion tonePerforming a bar code test 1. Perform test option 3=%KODAK 1. Select 1=EVALUATE Using the Evaluate optionStatic bar code evaluation 2. Select either 1=Transport Off or 2=Transport On8-12 Using the Imaging StationRight-side access door A-61092 September5. Tape the bar code sample section in place Dynamic bar code evaluation Dimensional Fields Pass or Fail Evaluating test resultsField Reflectance Fields Grades A through FGrade A PassCause Problem TypeTable 2 - Common Causes of Low Bar Code Ratings Field1. Select 2=DISPLAY Using the Display optionUsing the %KODAK option ∙ Bar code was not readUsing the %NORM option The first time the test is run, the two percentages will be the same Using the Check Feeder / Check Stacker Using the check feederClearing jams in the check feeder Cleaning the check feeder Using the check stacker Using the Endorser Die stylesBefore you begin Changing the die drum Top cover2. Push down the locking lever 9. Raise the drum locking lever to secure the die drum assembly Changing the ink roller Setting the date and code number Selecting the Endorser mode Enabling the Endorser Changing the print positionUsing the Footswitch FootswitchEnabling the confirmation tone Footswitch Pressed actions Footswitch PressedAction Footswitch Released Footswitch Released actionsFootswitch Pressed Definition ActionUsing the Patch Reader Patch typesPatch code placement Before you begin Positioning the Patch ReaderCleaning the Patch Reader Enabling patch reading Enabling the patch code confirmation toneSensor Appendix A Basic Concepts ModesLinked modes Image addresses Using the Next key Assigning an image address∙ Enter Using Function Code F92 Indexing schemes Image address formatsSingle level indexing Two level indexing Pageeach document is defined as follows Three level indexing Page…Three level offset indexing Controlling document level changes A-61092 9/99 Eastman Kodak Company Printed in U.S.A DOCUMENT I M A G I N GEASTMAN KODAK COMPANY Document Imaging Rochester, New York Printed on recycled paper