Keypad Operating Settings, JP1 | Madrigal Imaging MP-8, MP-9

INSTALLATION & SETUP

Keypad Operating ➤ Settings

JP1

This jumper setting is important if the keypad is configured for remote operation. There are two keypad protocols: A and B. These protocols are available to allow two projectors in the same room to be independently con- trolled by separate remote keypads. The protocol setting of the keypad must

match that set in the projector’s Keypad Options menu ( UTIL 6 7 ). For more information about keypad protocols, refer to the Remote Control Options entry in section 3.7, Utility Features.

JP2

This jumper must always be set between pins 1 and 2 as shown; otherwise, the projector will not respond correctly to keypad commands.

JP3

This jumper must always be set between pins 1 and 2 as shown; otherwise, the backlit feature will be disabled and the projector will not respond correctly to keypad commands.

JP4

The JP4 jumper setting sets the keypad type. If you are converting the key- pad to an IR remote, move the JP4 jumper from between pins 2 and 3 to between pins 1 and 2.

Step 3

For an IR remote keypad, place four AA size, 1.5V alkaline batteries in the compartment ensuring that the +/– orientation of each battery is correct. Position the compartment door into place.

For a wired remote keypad, an optional accessory cable (#03-001106-02P) is required. Plug the cable into the cable connector then position the door into place. Plug the cable jack into the remote jack input on the projector.

WARNING: DO NOT INSTALL BATTERIES IN THE KEYPAD IF A BUILT-IN OR WIRED REMOTE CABLE IS ATTACHED TO IT. THIS MAY CAUSE THE BATTERIES TO EXPLODE.

The keypad includes its own memory to store keypad operating settings. With a few simple keystrokes you can over-ride the “hard wire” protocol setting (explained earlier) and enable or disable the backlit feature. Keypad battery life is increased if the backlit feature is disabled. The new operating settings are stored in the keypad until the batteries are replaced (IR remote keypad) or the keypad connection cable is unplugged (wired or built-in keypad).

2.10

Image 16

Madrigal Imaging MP-8, MP-9 manual Keypad Operating Settings, JP1

Contents

MP-8 MP-9 Projectors Typographical Conventions Table of Contents Page Projector IntroductionFunctional Description Madrigal Imaging Service Location Purchaser’s Record and Servicing Installation & Setup Installation Considerations Adjust the DisplayStep Select the Input Rear Screen, Ceiling Mount Installation Front Screen Installations Rear Screen Installations Audience Coverage with Curved Screen Screen Size Throw DistanceSpecified by diagonal size Tune display size Poor Screen Placement Considerations OtherDesign of your projection system Setup HardwareKeypad Conversion Battery Compartment Keypad Operating Settings JP1 All keystroke settings Brite Tint Detail 2 . If pressed accidentally, press Floor Mount MountingCeiling Mount Rear Screen Optical Rear Screen Systems 13.Diffused Rear Screen Installation Diffused Rear Screen Systems Power Connection Source Connections Serial Port Connections 17.Built-in RGB Interface Connections Optical Alignment Blue Green Red Blue Green 22b. MP-8 Lens Assemblies Front View Step On the MP-9, tighten the three bolts labeled B On the MP-9, locate the two Keep the center defocused Lens mounting plate. Turn To display the next Center horizontal line is perpendicular to the vertical BeforeAfter Memory About Setup MemoriesMust be repeated About ASI and ASR Setup Step ASR Example #1 23.ASR System Example #1 ASR Example #2 24.ASR System Example #2 Acon Setup 29.ACON Installation Examples Installation and Setup OperationOverview Projector Basics Built-in Keypad Wired Remote KeypadIR Remote Keypad Full Function Keypad Key Press Rules Menus SlidebarsDialog Boxes Message Boxes Help PagesTest Patterns Context Sensitive Help Guided Source Setup Guided Mechanical SetupUsing Help Guided Help Rear Panel LEDs System Status Audio Mute FunctionsPages Input Source SelectionSelection Example Rear view Direct Channel Preferences entry in Section Up/Down ChannelSource Message Setup Memories Operation Display Adjustments Memory Allocation Locking Setup Memories Primary Display Brightness Adjustments Contrast Color DetailTint Picture Functions PositionSize White Balance Focus Sync Fast/SlowBlanking Top/Bottom/Left/Right Auto Clamp On/Off Decoder Options Retrace Short/LongVideo Standard Signal Routing About the Sync Routing System Keystone Geometry FunctionsSide Pin Bottom TopBow Linearity Skew Convergence Registration Guided Convergence registrationConvergence Interpolated Random Access Acon Automatic Convergence Automatic Convergence Full, Touchup, and Center Only Error Messages Interrupting Acon Learn Screen Auto, Manual Item 2, Channel List, allows you to program the Channel List Copy Setup Source SetupASI with Save Current Setup Locked/Unlocked ASR On/Off Message to indicate the action taken. If an Input When to use the ASR feature An Installation using the ASR Feature Clear Current Setup Select Internal Frequency Be cleared by pressing Name Field Input FieldRecall Memory Field Up/Down Field U/D Input Memories Auto Power-up On/Off PreferencesScreen Messages On/Off Blanking Time Auto, 0.5s to 5.0s Keypad Options Programmable Events On/OffIR Sensor Remote Jack Communication SetupProjector Clock/Events Baud RateSet Clock Time Programmable Events Type Field Type Field Events Interval Field Enabled FieldStart Field General Notes about Programmable Events About Channel Up/Down Events Multi-projector Functions ProjectorPage Guidelines MaintenanceLabels Markings Projector Location Power Cord AttachmentsVentilation Slots Servicing Cleaning Lens Cleaning Case Cleaning Acon CleaningProjector Response Problems Symptom Cause/Remedy Brightness to their proper settings Contact your dealer or Madrigal for assistance You may not be holding down the key long enough to initiate Symptom Projector does not respond to the Stby or Mute keysOne second Symptom Symptom Display is very faintContrast or brightness settings may be set too low Projection room may be too bright. Lower the intensity Maintenance Color and tint settings may require adjustment Symptom Display is not rectangular in shapeGeometry settings. Press Geom for the Geometry menu Message. If a Is displayed, unlock the setup. Press Util 1 Acon Errors Page Specifications Specifications Vertical Deflection Horizontal Deflection Power High VoltageRequirements Inputs Weight AccessoriesEnvironment Maximum Operating Range Storage Projector Dimensions PhysicalPage Glossary Color Temperature AutolockBandwidth Blanking Time Current Setup MemoryGain or Screen Gain Gamma CorrectionGeometry Help Locator Assembly Learn ScreenLine of Best Viewing Operation Level Optical ScreenPAL Video Pincushion Setup Memory Projector Retrace TimeRise Time RGB Video Glossary Glossary Page Menu Tree Menu Tree ASR/ASI Logic Diagrams Match Input memory No match Memory ASR/ASI Logic Diagrams Communication Cables RS-232 Serial CommunicationsPage Keypad Reference Page Throw Distance Tables Table F-1Throw Distance for MP-8 inches Table F-1Throw Distance for MP-8 cm Table F-1Throw Distance for MP-9 inches Table F-1Throw Distance for MP-9 cm Lenses Throw Throw Distance Distance Formula Formula Screen ScreenPage Index INDEX.2 DAY Limited Warranty