Madrigal Imaging MP-8, MP-9, MP-9 ASR/ASI Logic Diagrams, B.3

Appendix C

ASR/ASI Logic Diagrams

A change in scan frequency is detected.

A source, Recall memory, or channel was manually

The change is greater than 100 Hz horizontal

selected. The H & V scan frequencies of the source

or greater than 1 Hz vertical.

do not match that of the selected setup memory.

no

Is ASR

yes

yes

Is ASR

no

set to On for the

set to On for the

currently selected

selected

input?

input?

Do nothing.

Switch to the selected

Check the

source and/or setup

match

Input memory of the

no match

memory.

currently selected input for

matching H & V scan

frequencies.

match

Search for a

no match

Change the current

Recall memory with

setup memory to the

matched Input memory.

matching H & V scan

frequencies.

ASI

Logic

Begins

Adjustments made at this point are stored in the current setup memory.

ASR Logic Diagram

Change the current

setup memory to the

match

Search for an

no match

matched Recall memory.

Input memory with

matching H & V scan

frequencies.

Use the display settings

Create new display set-

ASI

tings by interpolating the

of the matched Input

two closest setup mem-

memory but do not update

Functions

ories (in freq.). Do not

the current setup memory.

update the setup memory.

Adjustments made at this

point are displayed but

NOT stored in the current

setup memory.

B.3

Contents

Page NOTICE CAUTION Typographical Conventions Table of Contents Page Introduction 1.1 The Projector 1.2Purchaser’s Record and Servicing Installation & Setup Quick Setup 2.2Installation Considerations Rear Screen, Ceiling Mount Installation Rear Screen, Floor Mount With Mirror Figure 2-1. Audience Coverage with Flat Screen Figure 2-2. Audience Coverage with Curved Screen Screen Size and ➤ Screen size and throw distance are interrelated. (See Appendices F and G.) Throw Distance As screen size increases, the distance between the projector and the screen also increases. During projection room design, make sure that the room Figure 2-3. Poor Screen Placement Figure 2-4. Good Screen Placement 2.3 Hardware Built-in Keypad Access Figure 2-7. Battery Compartment Figure 2-8.Jumper Settings Keypad Operating ➤ Settings JP1 Remote Control Options Utility Features JP2 Table 2-2. Operating Configurations 2.4 Mounting Figure 2-11. Ceiling Mount Installation Figure 2-12. Optical Rear Screen Installation Figure 2-13. Diffused Rear Screen Installation Figure 2-14. Folded Optics Folded Optics 2.5Power Connection 2.6Source Connections 2.7Serial Port Connections 2.8Optical Alignment Figure 2-19. Front Top Cover Figure 2-20. Front Top Cover Removal Blue Green Red Figure 2-21a. MP-9Lens Assemblies - Top View Figure 2-21b. MP-8Lens Assemblies - Top View Blue Green Figure 2-22a. MP-9Lens Assemblies - Front View Figure 2-22b. MP-8Lens Assemblies - Front View Page Page Page Page Page Source Setup Page Page 2.10 Memory Page Page ASR Setup ASR Example #1 Figure 2-23. ASR System Example #1 Figure 2-24. ASR System Example #2 Page (kit# 38-8000805-01).See Figure Figure 2-29. ACON Installation Examples Figure 2-30. Remote Locator Assembly Placement Operation Overview Projector Basics OPERATION Built-inKeypad The keypad can be accessed as follows: Figure 3-1. Built-inKeypad Access IR Remote Keypad Figure 3-2. Full Function Keypad Page Page Message Boxes Help Pages Using Help Test Patterns (i.e., no overlayed text), pressing To view help describing a menu, press HELP while the menu is displayed Guided Help 1. Guided Source Setup 2. Guided Mechanical Setup 3. Source Selection Guide Power-on Figure 3-3. Rear Panel LEDs Standby Mode POWER LED restored and the LED is turned off Page 3.3Source Selection Figure 3-4. Projector Slots Figure 3-5. Switcher Slots press SOURCE 1 3 the switcher’s front panel push buttons Direct Channel ➤ This method of source selection takes advantage of the Channel List feature explained in section 3.7, Utility Features. The Channel List allows you to Channel 08 in the Channel List was programmed to select a source connected to slot 5 on switcher 3. To select this source, simply press UTIL 5 4 ) is set Preferences entry in Section Up/Down Channel ➤ 3.4Setup Memories Page 3.5Display Adjustments Convergence Registration Primary Display ➤ Brightness Adjustments The Brightness function is used to adjust the black level of the image Note: If room lighting changes, it may be necessary to re-adjustbrightness Page Picture Functions ➤ Position Size White Balance Page Page Figure 3-6. Connection of Composite Video or S-Videoto RGB Input (Multi-StandardDecoder Option Required) Page Geometry ➤ Functions Keystone Side Pin The two displays shown below demonstrate side pincushion adjustment To adjust side pincushion, select Side Pin from the Geometry menu then press Page Page 3.6Convergence Registration Page Page Page ACON Automatic ➤ Automatic Convergence – Full, Touchup, and Center Only Page Page Item 1, Source Setup Item 2, Channel List, allows you to program the Channel List Item 3, Recall Memories Item 4, Input Memories Item 5, Preferences Item 6, Remote Control Options Item 7, Clock/Events Item 9, Service Page ASR is also performed when: •You switch to an input which has ASR set to On •You select a Recall memory and ASR is set to On for the current input •A channel is selected which specifies an input which has ASR set to On If, on the other hand, an ASI is performed, a source Figure 3-7. An Installation using the ASR Feature Clear Current Setup Select Internal Frequency Page Page Page Preferences ➤ Auto Power-up(On/Off) If Auto Power-upis set to On, the Screen Messages (On/Off) messages, and the Page Figure 3-8. Independent IR Keypad Control Clock/Events ➤ Baud Rate Set Clock Time Date Page The Type Field Table 3-1. Type Field Events The Interval Field Table 3-2. Interval Field Options The Start Field The Enabled Field Page 3.8Multi-projectorFunctions Page Maintenance 4.1Warnings and Guidelines This is a safety feature 4.2 Cleaning 4.3Trouble- shooting Page Page Page Page Page Page Page Specifications 5.1 Specifications Page Page Page Page Page Glossary Page Page attenuate incident light; screens with gain more than 1 direct more incident light to the audience but have a narrow viewing angle. For example: An image reflecting off a 10 gain screen appears 10 times brighter than it would if reflected off a matte white wall. Curved screens usually have larger gain than flat screens Page Page Page Page Page Page Menu Tree Page ASR/ASI Logic Diagrams ASR/ASI LOGIC DIAGRAMS B.4 Communication Cables Page Keypad Reference Page Throw Distance Tables THROW DISTANCE TABLES Table F-1 Throw Distance for MP-8(cm) F.2 Table F-1 Throw Distance for MP-9(inches) F.3 Table F-1 Throw Distance for MP-9(cm) F.4 Lenses Page INDEX.1 INDEX.2 90-DAYLIMITED WARRANTY