|
|
| Troubleshooting | ||
|
|
|
|
|
|
|
|
|
|
|
|
Error | Error message | Recommended Action |
|
| |
code |
|
| |||
|
|
|
|
| |
0B8F | Could not redirect the console - BMC | Turn off the power once and then on again to | |||
| Parameter Error - | start the server. | If the error cannot be | ||
0B90 | BMC Platform Information Area corrupted. | corrected, contact your service representative. | |||
0B91 | BMC update firmware corrupted. |
|
|
|
|
0B92 | Internal Use Area of BMC FRU corrupted. | This is not a fatal error. | Turn off the power | ||
|
| once and then on again to restart the server. | |||
|
| If the error cannot be corrected, contact your | |||
|
| service representative. |
|
| |
0B93 | BMC SDR Repository empty. | Turn off the power once and then on again to | |||
|
| restart the server. If the error cannot be | |||
|
| corrected, contact your service representative. | |||
0B94 | IPMB signal lines do not respond. | This is not a fatal error. | Turn off the power | ||
|
| once and then on again to restart the server. | |||
|
| If the error cannot be corrected, contact your | |||
|
| service representative. |
|
| |
0B95 | BMC FRU device failure. | This is not a fatal error. | Turn off the power | ||
|
| once and then on again to restart the server. | |||
|
| If the error cannot be corrected, contact your | |||
|
| service representative. |
|
| |
0B96 | BMC SDR Repository failure. | Turn off the power once and then on again to | |||
0B97 | BMC SEL device failure. | start the server. | If the error cannot be | ||
|
| corrected, contact your service representative. | |||
0B98 | BMC RAM test error. | ||||
0B99 | BMC Fatal hardware error. |
|
|
|
|
0B9A | Management controller not responding. | Update the RMC firmware. If the error cannot | |||
|
| be corrected, contact your service | |||
|
| representative. |
|
|
|
0B9B | Private I2C bus not responding. | Turn off the power once and then on again to | |||
0B9C | BMC internal exception. | start the server. | If the error cannot be | ||
0B9D | BMC A/D timeout error. | corrected, contact your service representative. | |||
0B9E | SDR repository corrupt. |
|
|
|
|
0B9F | SEL corrupt. |
|
|
|
|
0BB0 | SMBIOS – SROM data read error. | Contact your service representative. | |||
0BB1 | SMBIOS – SROM data checksum bad. |
|
|
|
|
8100 | Memory Error detected in DIMM group #1. | Contact your service representative to replace | |||
8101 | Memory Error detected in DIMM group #2. | the DIMM in the relevant group. | |||
8102 | Memory Error detected in DIMM group #3. |
|
|
|
|
None | Expansion ROM not initialized – PCI Mass | Disable initialization of the optional device | |||
| Storage Controller in slot n (n: slot number) | expansion ROM by using the BIOS SETUP | |||
|
| utility (see Chapter 4). |
|
| |
| H/W Configuration of BMC is corrupted. | Use the NEC EXPRESSBUILDER to | |||
| !! Update BMC F/W Configuration by | configure the remote management card (see | |||
| configuration tool !! | Chapter 6). |
|
|
|
| !! Refer to BMC configuration manual !! |
|
|
|
|