Philips M3500B Discontinuing SpO2 Monitoring, Caring for Sensors

Discontinuing SpO2 Monitoring

M3500B HeartStart XLT Defibrillator/Monitor 5-9

Discontinuing SpO2 Monitoring

To shu t off SpO2 monitoring, press repeatedly until nothing appears

below the softkey.

Figure 5-5 SpO2 Monitoring Off

Caring for Sensors

Refer to the manufacturers instructions for care and cleaning of sensors. To

get the best results from your SpO2 reusable sensors, always handle the sensor

and cable with care and protect them from sharp objects. The sensor sleeve

houses a sensitive electronic device that can be damaged. Harsh treatment of

sensors will drastically reduce their lifetime.

WARN ING Do not use a damaged sensor or one with exposed electrical circuits.

6S2

PAUSE

HR ALARM LEAD

SELECT

ANALYZE

Shocks: 3

00:00:49

Monitoring Rhythm

78 Pads

SpO2

Contents

Main Page Page ii 1RWLFH About This Edition Edition History Copyright Medical Device Directive Conventions Page Contents Page Page Page Page Page 1 Introduction Page Intended Use Defibrillation Therapy Indications for AED Therapy Contraindications for AED Therapy Precautions for AED Therapy Indications for Manual Defibrillation Therapy Contraindications for Manual Defibrillation Therapy Precautions for Manual Defibrillation Therapy Noninvasive Pacing Therapy Indications Contraindications SpO2 Monitoring Indications Contraindications Page Page 2 Getting Started Getting Acquainted Basic Orientation Page Manual Mode Controls Page Page Page Getting Acquainted 2-8 Getting Started Figure 2-5 Manual Mode Display Layout 114J LCD Backlight 150J 132 86 Connecting to Power Inserting the Battery Removing the Battery Low Battery Warning Using a Data Card Inserting a Data Card Page Page 3 Defibrillating in AED Mode Page Page Defibrillation Preparation Defibrillating Page 2. If instructed, press . Page 3. If shock advised, press . Automatic Re-analysis On Pausing for CPR Page Monitoring Rhythm Page ERC Protocol Page Troubleshooting 3-18 Defibrillating in AED Mode Table 3-1 AED Mode Prompts Prompt Possible Cause Corrective Action 4 Monitoring the ECG Applying Monitoring Electrodes Electrode Placement Page Selecting the Lead 78 Setting the Heart Rate Alarm Disabling the HR Alarm Adjusting the ECG Size Page 5 Monitoring SpO Understanding Pulse Oximetry Selecting a Sensor Table 5-1 shows the SpO2 sensors that may be used with the HeartStart XLT. patient cable to the HeartStart XLT. (See Connecting the SpO2 Patient Cable on page 10-5.) Reusable Sensors Disposable Sensors Semi-disposable Sensors Applying the Sensor Page Monitoring Setting Alarms Responding to an Alarm 87 Discontinuing SpO2 Monitoring Caring for Sensors Troubleshooting 5-10 Monitoring SpO2 The table below lists system messages that you may encounter when monitor- ing SpO Table 5-2 System Messages Problem or Message Possible Cause Corrective Action 6S21RQ3XOVDWLOH 6S2/RZ6LJQDO 6S21RLV\6LJQDO Page Page 6 Defibrillating in Manual Mode Enabling Manual Mode Preparation Defibrillating 1. Select Energy 2. Charge 3. Shock 150 J 87 J Returning to AED Mode 7 Performing Synchronized Cardioversion Preparing for Synchronized Cardioversion Delivering a Synchronized Shock 150 J 87 J Delivering Additional Synchronized Shocks Disabling Sync Mode Page Demand Mode Versus Fixed Mode Monitoring During Pacing Preparing for Pacing Pacing 78 Page Changing Pacing Modes Defibrillating During Pacing /HDGV2II 3DFHU)DLOXUH 3DFHU2XWSXW /RZ 6WRS3DFHU .H\,QD FWLYH Page 9 Storing, Retrieving & Printing Marking Events Events Recorded The following events and related information are stored in the Event Summary: Page Creating a Patient Record Printing the Internal Event Summary Page Printing Events 10 Setting Up and Configuring the HeartStart XLT Connecting/Disconnecting Patient Cables Connecting the Pads Patient Cable Disconnecting the Pads Patient Cable Page Connecting the SpO2 Patient Cable Disconnecting the SpO2 Patient Cable Arranging Accessories in the Carrying Case Configuring the HeartStart XLT Accessing the Configuration Menu Configurable Parameters Page Page Page Page Setting the Manual Mode Password Page Modifying the Configuration Returning to the Default Configuration Saving Settings to a Data Card Loading Settings from a Data Card Printing Settings 11 Maintaining the HeartStart XLT Operational Checks Before You Begin Page Shift/System Check Page Page Battery Capacity Test (CT) Battery Maintenance Charging Batteries Battery Capacity Battery Life-Expectancy Storing Batteries Discarding Batteries Page Page Cleaning Instructions Cleaning the HeartStart XLT Cleaning the Carrying Case Cleaning the Printer Printhead Cleaning the Power Modules Cleaning Pads, Electrodes & Cables Removing & Replacing the Carrying Case Page Page Supplies & Accessories Page Page Page Page 12 Troubleshooting System Messages Page Page Momentary Messages Troubleshooting Tips Table 12-3 lists some situations that you may encounter , causes, and actions to take. Page Calling for Service Other International Areas Page Specifications Defibrillator Defibrillator (cont.) ECG Monitoring Display Thermal Array Printer Thermal Array Printer (cont.) Battery and Battery Power Module Noninvasive Pacing SpO2/Pulse Oximetry Event Storage General Environmental Symbol Definitions ! Page Page Page Clinical Performance Summary - Defibrillation Methods Results Conclusion Clinical Performance Summary - Cardioversion Methods Results Page Page Safety Considerations Page Page Electromagnetic Compatibility Reducing Electromagnetic Interference Restrictions for Use Immunity Level Page Index A B C D E F H I K L M N O P Q R S T U V W