Manuals / Q-Logic / Computer Equipment / Switch

Q-Logic SANBOX2-16, 59022-11 A 4-13 manual Domain ID and Domain ID Lock

Models: 59022-11 A 4-13 SANBOX2-16

1 322

Download 322 pages 943 b

Page 128

4 – Managing Switches	0
4 – Managing Switches
Configuring a Switch

4.7.2.3

Domain ID and Domain ID Lock

The domain ID is a unique Fibre Channel identifier for the switch. The Fibre Channel address consists of the domain ID, port ID, and the Arbitrated Loop Physical Address (ALPA). The maximum number of switches within a fabric is 239 with each switch having a unique domain ID.

Switches come from the factory with the domain IDs unlocked. This means that if there is a domain ID conflict in the fabric, the switch with the highest principal priority, or the principal switch, will reassign any domain ID conflicts and establish the fabric. If you lock the domain ID on a switch and a domain ID conflict occurs, one of the switches will isolate as a separate fabric and the Logged-In LEDs on both switches will flash to show the affected ports. Refer to the ”Set Config Command” on page A-60for information about the Switch keyword and the Domain ID Lock and Principal Priority parameters.

If you connect a new switch to an existing fabric with its domain ID unlocked, and a domain conflict occurs, the new switch will isolate as a separate fabric. However, you can remedy this by resetting the new switch or taking it offline then back online. The principal switch will reassign the domain ID and the switch will join the fabric.

Note: Domain ID reassignment is not reflected in zoning that is defined by domain ID and port number pair. You must reconfigure zones that are affected by domain ID reassignment.

4-22	59022-11 A

Image 128

Q-Logic SANBOX2-16, 59022-11 A 4-13 manual Domain ID and Domain ID Lock

Contents

SANbox2-8c/16 Switch Management User’s Guide SANbox2-8c/16 Switch Management User’s Guide Document Revision HistoryTable of Contents Section Managing Fabrics SANbox2-8c/16 Switch Management Working with Device Information and Nicknames Zoning a Fabric Section Managing Switches Changing a User Account PasswordChanging the Default Performance View File Encryption Key Section Managing PortsAppendix a Command Line Interface 103106 109Glossary Index Figures Tables Port Threshold Alarm Configuration Defaults 131Intended Audience Related MaterialsJdom License Technical Support AvailabilityTraining Contact InformationIntroduction Technical Support 59022-11 a Using SANsurfer Switch Manager Workstation Requirements Installing the Management ApplicationWorkstation Requirements SANsurfer Switch Manager Change directory to the location of the install programFor a Windows platform For a Linux platformSMS Installation for Windows SANsurfer Management SuiteFor a Mac OS X platform Open the CD and move to the following folderChglax.bat SMS Installation for Linux SMS Installation for Solaris Locate and execute the file sbmoversms.sh Install the new SANsurfer Switch Manager packageChange directories to the package location Starting SANsurfer Switch Manager ‰ For Linux or Solaris enter the SANsurfer command Initial Startup DialogSANsurfer Switch Manager Window Save Default Fabric View File Dialog Exiting SANsurfer Management SuiteUninstalling SANsurfer Switch Manager Load Default Fabric File DialogSMS Uninstall Installdirectory/UninstallData/SANsurferUninstallerStandalone Uninstall Changing the Encryption Key for the Default Fabric View FileSetting SANsurfer Switch Manager Preferences Saving and Opening Fabric View FilesPreferences Dialog SANsurfer Switch Manager Using Online Help Viewing Software Version and Copyright InformationFaceplate Display SANsurfer Switch Manager User InterfaceTopology Display Menu options in the topology display are shown in Figure Menu BarTopology Display Menu Menu options in the faceplate display are shown in Figure Faceplate Display MenuShortcut Keys Tool Bar Tool Bar ButtonsFabric Tree Fabric TreeData Window and Tabs Working Status IndicatorGraphic Window Using the Topology Display Switch and Link StatusArranging Switches in the Display Working with Switches and LinksSelecting Switches and Links Opening the Faceplate Display and Topology Popup Menus Topology Data WindowsUsing the Faceplate Display Port Views and StatusWorking with Ports Selecting PortsOpening the Faceplate Popup Menu Faceplate Data Windows Page Managing Fabrics Radius ServersAdding a Radius Server Add ServerManaging Fabrics Removing a Radius Server Remove ServerEditing Radius Server Information Edit Radius Server InformationModifying Authentication Order Radius Server Information Modify Authentication Order Radius Server InformationFabric security consists of the following Securing a FabricConnection Security Security Consistency Checklist User Account SecurityDevice Security Edit Security Dialog Edit Security DialogCreating a Security Set Create Security Group Dialog Create Security Group DialogCreating a Security Group Create Security Group Member Dialog Create a Security Group Member DialogCreating a Security Group Member Editing the Security Configuration on a Switch Using the Security Config Dialog Viewing Properties of a Security Set, Group, or MemberDeactivating a Security Set Archiving a Security Configuration to a FileActivating a Security Set Configured Security Data Window Fabric ServicesEnabling Snmp Configuration Active Security Data WindowClick the In-band Management Enable button Enabling In-band ManagementTracking Fabric Firmware and Software Versions Saving a Version SnapshotViewing and Comparing Version Snapshots Exporting Version Snapshots to a FileManaging the Fabric Database Adding a FabricRemoving a Fabric Opening a Fabric View FileRediscovering a Fabric Adding a New Switch to a FabricSaving a Fabric View File Replacing a Failed Switch Deleting Switches and Links Displaying Fabric InformationTopology Display Switch and Status Icons Fabric StatusDisplaying the Event Browser 11. Events BrowserSeverity Levels IconFiltering the Event Browser 12. Filter Events DialogSorting the Event Browser Saving the Event Browser to a FileDevices Data Window Devices Data Window EntriesActive Zone Set Data Window 13. Active Zone Set Data WindowSANsurfer Switch Manager enables you to do the following Link Data WindowWorking with Device Information and Nicknames Displaying Detailed Device InformationCreating a Nickname Exporting Device Information to a FileManaging Device Port Nicknames Exporting Nicknames to a File Editing a NicknameDeleting a Nickname Zoning Concepts Importing a Nicknames FileZoning a Fabric Zones Soft ZonesZone Sets Access Control List Hard ZonesAliases Zoning Database Managing the zoning database consists of the following Using the Zoning WizardManaging the Zoning Database Editing the Zoning Database 15. Edit Zoning DialogEdit Zoning Dialog Tool Bar Buttons and Icons Configuring the Zoning Database 16. Zoning Config DialogDefault Visibility Interop Auto SaveDiscard Inactive Saving the Zoning Database to a FileRemoving All Zoning Definitions Restoring the Default Zoning DatabaseRestoring the Zoning Database from a File Managing Zone Sets Creating a Zone SetActivating and Deactivating a Zone Set Copying a Zone to a Zone SetRemoving a Zone from a Zone Set or from All Zone Sets Removing a Zone SetManaging zones involves the following Managing ZonesCreating a Zone in a Zone Set Adding Zone Members Renaming a Zone or a Zone Set Removing a Zone MemberRemoving a Zone from a Zone Set Click the OK button to add the member and save the changeManaging Aliases Removing a Zone from All Zone SetsChanging Zone Types Creating an Alias Adding a Member to an AliasZone Merge Failure Removing an Alias from All ZonesMerging Fabrics and Zoning Zone Merge Failure Recovery Managing Switches Managing User Accounts Factory User AccountsUser Account Administration Dialog Add Account Creating User AccountsUser Account Administration Dialog Remove Account Removing a User AccountChanging a User Account Password User Account Administration Dialog- Change PasswordUser Account Administration Dialog Modify Account Modifying a User AccountDisplaying Switch Information Faceplate DisplaySwitch Data Window Switch Data Window EntriesRatov Switch Data Window Entries Displaying Detailed Device Information on page 3-34for Port Statistics Data Window Port Information Data Window Faceplate Display Port InformationConfigured and Active Zonesets Data Window Configured Zonesets Data WindowConfiguring Port Threshold Alarms Port Threshold Alarm Configuration DialogPaging a Switch EventCount Sample WindowSetting the Date/Time and Enabling NTP Client Resetting a SwitchSwitch Resets Type DescriptionConfiguring a Switch Using the Configuration WizardSwitch Properties 10. Switch Properties DialogSwitch Administrative States Symbolic NameSwitch Administrative States Domain ID and Domain ID Lock Fabric Device Management Interface Broadcast Support In-band ManagementAdvanced Switch Properties Interop Mode for ZoningLegacy Port Address Format Timeout ValuesTimeout Values System Services Dialog 12. System Services DialogSecurity Consistency Checklist Dialog Network Properties 13. Network Properties DialogIP Configuration IP Configuration ParametersRemote Logging NTP ClientSnmp Properties 14. Snmp Properties DialogSnmp Configuration Snmp Configuration ParametersSnmp Trap Configuration Snmp Trap Configuration ParametersArchiving a Switch Restoring a Switch 15. Restore Dialogs Full and SelectiveManaging Switches Restoring the Factory Default Configuration Factory Default Configuration SettingsDownloading a Support File Installing Firmware Displaying Hardware Status 16. Hardware Status LEDsManaging Switches Displaying Hardware Status 59022-11 a Managing Ports Displaying Port InformationPort Types Monitoring Port StatusDisplaying Port Types Displaying Port Operational States Displaying Port SpeedsPort Operational States Port SpeedsDisplaying Transceiver Media Status Transceiver Media ViewPort Statistics Data Window Entries LIP ALPD,ALPS Port Information Data Window Entries Port Information Data Window Entries Port Information Data Window Entries Configuring Ports Port Properties DialogChanging Port Administrative States Port Administrative StatesChanging Port Speeds Changing Port Types Stream GuardDevice Scan Changing Port Symbolic NameUsing the Extended Credits Wizard Designate Donor Ports Resetting a Port Testing PortsTesting Ports Graphing Port Performance Fabric View GraphsThis section describes how to do the following Starting SANsurfer Performance ViewerSave Default Performance View File Dialog Exiting SANsurfer Performance ViewerSaving and Opening Performance View Files DisplayedChanging the Default Performance View File Encryption Key Setting SANsurfer Performance Viewer PreferencesSetting the Polling Frequency Displaying GraphsArranging Graphs in the Display Customizing GraphsManaging Ports Setting Global Graph Type Rescaling a Selected GraphPrinting Graphs Saving Graph Statistics to a FileCommand Line Interface Logging On to a SwitchWorking with Switch Configurations User AccountsModifying a Configuration Backing up and Restoring Switch Configurations Ftp ipaddress Commands Table A-1. Command-Line CompletionTable A-2. Commands Listed by Authority Level Admin Session CommandsAdmin Command AuthoritySyntax KeywordsAlias Command Syntax aliasRename aliasold aliasnew Members aliasRemove alias memberlist CIM Command CIMListener Command Table A-3. CIM Listener Configuration ParametersFollowing is an example of the CIMListener Create command EnterCIMSubscription Command Table A-4. CIM Subscription Configuration ParametersMust be Saved with the cim save command Config Command Syntax configKeywords activate configname Edit confignameRestore Manager Archive function are not compatible with the ConfigRestore command Save configname# ftp symbolicname or ipaddress Create Command CreateCertificate SupportCommand Line Interface Create Command Following is an example of the Create Certificate command Keywords MMDDhhmmCCYY Date CommandSyntax date Syntax firmware install Firmware Install CommandAuthority Admin Group Command Syntax groupKeywords add group Table A-5. ISL Group Member AttributesTable A-6. Port Group Member Attributes Copy groupsource groupdestination Create group typeEdit group member Table A-8. Group Member AttributesMembers group Remove group memberlistRename groupold groupnew Securitysets groupFollowing is an example of the Group Edit command ISLFollowing is an example of the Group List command Following is an example of the Group Members commandHardreset Command SyntaxHelp Command Keywords commandSyntax help command keyword Authority NoneHistory Command Authority None Syntax historyHotreset Command HotresetImage Command FTP. Enter one of the following on the command line Switch name associated with the IP addressEnter the following account name and password Are running the same version of firmwareOpen an Admin session to acquire the necessary authority Wait for the unpack to completeLip Command Following is an example of the Lip commandReinitializes the specified loop port Lip portnumberPasswd Command Syntax passwd accountname Keywords accountnamePing Command Syntax ping ipaddress Keywords ipaddressPs Command Following is an example of the Ps commandSyntax Examples Displays current system process informationSyntax quit, exit, or logout Quit CommandCloses the Telnet session Reset Command Config confignameServices SwitchSnmp SystemTable A-9. Switch Configuration Defaults ValuesTable A-10. Port Configuration Defaults ArbffTable A-11. Port Threshold Alarm Configuration Defaults Table A-12. Zoning Configuration DefaultsTable A-13. Snmp Configuration Defaults Table A-14. Radius Configuration Defaults Table A-15. Services Configuration DefaultsTable A-16. System Configuration Defaults Table A-17. Security Configuration DefaultsSecurity Command Keywords activeFollowing is an example of the Security Active command HistoryFollowing is an example of the Security History command Following is an example of the Security Limits commandFollowing is an example of the Security List command Securityset Command Delete securityset Groups securitysetRemove securityset group Rename securitysetold securitysetnewSet Command Syntax setSetup option Switch statePagebreak state Port optionSet Config Command Set configTable A-18. Set Config Port Parameters Port portnumberTable A-18. Set Config Port Parameters Security Table A-19. Security Configuration Parameters Table A-20. Set Config Switch ParametersRatov Table A-21. Set Config Threshold Parameters ThresholdTable A-22. Set Config Zoning Parameters Arbff Following is an example of the Set Config Security command Following is an example of the Set Config Switch commandFollowing is an example of the Set Config Threshold command Following is an example of the Set Config Zoning command Set Log Command Set logArchive Component filterlistSnmp Display filterLevel filter Port portlistStart StopAlarms are always logged and always displayed on the screen Set Port Command EnableKeywords portnumber Bypass alpaState state Set Setup Command Set setupRadius Services Snmp System Configuration fieldsTable A-23. Radius Service Settings Table A-24. Switch Services Settings Table A-24. Switch Services Settings Table A-25. Snmp Configuration Settings Table A-26. System Configuration Settings Table A-25. Snmp Configuration SettingsTable A-26. System Configuration Settings Following is an example of the Set Setup Services command Following is an example of the Set Setup Snmp command Following is an example of the Set Setup System command SANbox2 admin # set setup systemShow Command Keywords aboutAlarm option Cimlistener listenernameCimsubscription subscriptionname Fdmi portwwnLog option LsdbNs option PagebreakTable A-27. Show Port Parameters TbufLIPF8ALPS Post log Steering domainidTable A-28. Switch Operational Parameters WhoamiZoneset Active, List „ Zoning History, Limits, ListDisplays the current time zone setting TopologyDisplays all connected devices UsersFollowing is an example of the Show Domains command Following is an example of the Show Fabric commandFollowing is an example of the Show Fdmi command Following is an example of the Show Fdmi WWN commandFollowing is an example of the Show NS portID command Following is an example of the Show NS local domain commandFollowing is an example of the Show NS domainID command Following is an example of the Show Interface command Collisions0 txqueuelen100Following is an example of the Show Port command PL-XPL-VC-SG3-22Following is an example of the Show Switch command Following is an example of the Show Topology command59022-11 a 101 Following is an example of the Show Version command Show Config Command Show configFollowing is an example of the Show Config Switch command Following is an example of the Show Config Threshold command Following is an example of the Show Config Zoning commandShow Log Command NoneShow log Keywords numberofeventsSettings LevelOptions PortFollowing is an example of the Show Log command Following is an example of the Show Log Level commandFollowing is an example of the Show Log Options command Show Perf Command Following is an example of the Show Perf Byte command Mfg Show Setup CommandShow setup Following is an example of the Show Setup Services command Following is an example of the Show Setup Radius commandFollowing is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Shutdown Shutdown CommandPower from the switch Test Command TestPort portnumber testtype StatusAdmin start Test port x online Authority None Syntax uptime Uptime CommandExamples The following is an example of the Uptime command User Command UserAccounts AddFollowing is an example of the User Add command Following is an example of the User Edit commandFollowing is an example of the User Delete command Following is an example of the User List commandWhoami Whoami CommandFollowing is an example of the Whoami command Zone Command Syntax zoneMembers zone Remove zone memberlistRename zoneold zonenew Type zone zonetypeFollowing is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zonesetZones zoneset Remove zoneset zonelistRename zonesetold zonesetnew Zoning Command Opens a Zoning Edit sessionTable A-29. Zoning Database Limits Limit DescriptionFollowing is an example of the Zoning Limits command E1JBOD1 E2JBOD2Following is an example of the Zoning List command Command Line Interface Zoning Command 134 59022-11 a Access Control List Zone Administrative StateAlarm BootPClass 3 Service Configured Zone SetsDefault Visibility Fabric Management SwitchInput Power LED Inter-Switch LinkMaintenance Button Maintenance ModePower On Self Test Post Principal SwitchSANsurfer Switch Manager Small Form-Factor PluggableIndex Index-2 59022-11 a 59022-11 a Index-3 Index-4 59022-11 a 59022-11 a Index-5 Index-6 59022-11 a 59022-11 a Index-7 Index-8 59022-11 a 59022-11 a Index-9 Index-10 59022-11 a