Expanded operator control, Gap Length | Siemens A4027118-A0414

All rights reserved	Saw V1.4.doc
Copyright ♥ Siemens AG 2008	Manual SIMOTION Flying

Section B: The application example as demonstration system


O	t	t l f th	li ti	l
Flying Saw with SIMOTION			A4027118-A0414

Expanded operator control

Table 5-4: Expanded operator control in the automatic mode

No.	Action	Comment

1If the flying saw is in the AUTOMATIC-STOPPED, operating mode, you can select one of two possibilities:

1.Print Mark Simulation OFF

i.e. the demonstration case itself generates print marks using sensors. The cut length can only be changed in steps of complete revolutions.

2.Print MARK simulation ON

this means that the print marks – and therefore also the cut length – can be freely selected .

2If the print mark simulation has been activated, this character is displayed at the top left edge of the screen.

3You can change the cut length with the Cutlength slider. The system automatically calculates the minimum cut length from the data specified for the material velocity, cut duration, velocity for return positioning and the actual acceleration values. The maximum cut length is obtained from the minimum plus 1000!

4You can enter the cutting time using sel

For act

the remaining

cutting time is displayed during the cut itself.

5You can activate/deactivate the "gap" function using the Gap ON / OFF button

You can define the size of the gap by entering

Gap Length

V 1.4

Release 06/06/08

57/107

Image 57

Siemens A4027118-A0414 user manual Expanded operator control, Gap Length

Contents

Application number A4027118 -A0414 Simotion Flying Saw Copyright General Notes General Notes Warranty, liability and support Reference regarding export codes Qualified personnel Standard Simotion application Foreword Sec Description Tion Document structure List of contents Integrating the core flying saw functions Description of important program elements Error messages 101 Chap Title Contents ContentObjective Subjects discussed Basic information PrerequisitesObjective and purpose of this standard application Principle design of a flying saw Solution using the standard flying saw application Components included in the standard application Release 06/06/08 14/107 Uses Tasks that can be implemented using the core functionsApplications Controls that are permitted Precisely synchronizing at a specific position Properties and features of the core flying saw functionsFlying axis Starting position of the flying axis can be set Sensor Application environment Design of the flying saw Structure and functionGeneral design Physical quantities that can be parameterized Physical quantity Description Synchronous range Disable ErrorOperating states of the FlyingSaw-FB Starting position Manual Automatic Section B The application example as demonstration System Contents Classification Pictograms, signal words and textSevere bodily injury or even death Severe bodily injury or even death Responsibilities of the operator Correct use MisuseResponsible for monitoring Hardware structure and mounting/installation Qualification of personnelOverview Procedure CommunicationsHMI system Action Comment Installation Installing the standard Siemens softwareResetting Simotion D435 to the factory settings Minimum required releases Release 06/06/08 29/107 Release 06/06/08 30/107 Release 06/06/08 31/107 Yes PG/PC Interface PG/PC1 Setting the Ethernet address of the PG/PC Ethernet address Action Comment Page Downloading the Simotion project of the standard application Page Page Brief instructions to demonstrate Operator control of the application exampleDemonstrate Detailed operating instruction Structure overview to demonstrate the application Structure overview Brief instructions Print Mark Simulation on / OFFButton Flying Saw Startpos Material END button Material Start button and continue with Step Process screenPage Simodrive Detailed operating instructions Start Welcome screen General screen areas Button Function Machine geometry Distance to sensor Machine parameter settingsStartPosition StartSyncPosition System Operator control functions in the setting-mode Operator functions of the process in the automatic mode Standard operator control Page Gap Length Expanded operator control Display areas Flying saw mode 10 Technology view of the flying saw Technology view 11 Status Operator control functions in the status display Section C Integrating the core flying saw functions Function and identification of the program groups Program environment and interfaces Pro Program Data Gram Unit Module Section Program structure FBBGDTEMPLATEFlyingSaw IPO Call environment InterfacesClassifying the interfaces Block interface of the FBBGDTEMPLATEFlyingSaw False Queued mode changeover is Activated using this input INT Parameter Data type Initial value Description Output parameter OUT Structure of the global data area of the data unit FSVar Physical quantities Parameter Data type Initial Description Value Restart This is how you integrate core functions into your project Integrating the core flying saw functions Simotion control Hardware element Diagram Order No./MLFB and functions Technology objects Technology objects required and synchronous relationships Preparations De-archiving the standard flying saw applicationDownloading the core functions into your Scout project Setting-up the required technology objects Axis, material web Configuration Monitoring functions closed-loop controlPre-assignment limits Assigning the synchronous relationships FlyingSawAxisSYNCHRONOUSOPERATION ConfigurationPre-assignment gear synchronization Pre-assignment dynamic Integrating into your application Calling the FlyingSaw FB in the user programCalling the FBBGDTEMPLATEFlyingSaw in ST and FBD Assigning the instance Integrating the template block in the processing sequenceInstance Mode changeover sequence Using the FBBGDTEMPLATEFlyingSawGeneral information and instructions Initial state of the FBBGDTEMPLATEFlyingSaw Changing-over the mode AutomaTic Using the restart bit Error messagesRestart after a new start Release 06/06/08 84/107 Help routines Help functions within the core flying saw functions Objectives Section D Program description Before carrying-out changes Information and warnings Program structure Description of important program elementsDeclaration part FSVar Declaration section Instruction section Functions of the FBBGDTemplateFlyingSaw FlyingSaw-FB Static variablesDeclarations Automatic state change sequences Axis monitoring functions State machine of the FlyingSaw FB Error Æ Disable Step Function Comment Mode Error Disable Æ Disable Step Function Comment Mode DisableDisable Æ Error Disable Æ Starting position Starting position Æ Error Step Function Comment Disable Æ ManualStarting position Æ Disable Mode, starting position Starting position Æ Manual Step Function CommentMode, automatic Automatic cycle Automatic Æ Disable Automatic Æ Error Manual Æ Disable Manual Æ ErrorAutomatic Æ Starting position Mode, manual Properties/features of the IPOFS1IPORoutine Properties/features of startupSAPHelp routines SyncPos buffer FBBGDFSSPBin FBBGDFSSPBresetFBBGDFSSPBout FBBGDFSSPBread Scope of supply General information on the applicationRevisions/Author Version Date/Revision Author Error messages ErrorID Explanation Error codeUsersInterface.grEndPos Enablegearing DisablegearingGap pos Details in FSVar structure under FRpossuperimpFSA Section E Appendix Section E Appendix Applicationcenter Contact partner Evaluation of the document Please help us to become even better