3 Chapter Menu
Menu Windows
4CUT ENABLE buttons
When the CUT button on the CR MONITOR section is lit, you can cut the monitor signal by touching the desired CUT buttons, L, R, SURR L to SURR RS on the window.
The SURROUND L, C, SW, R. LS and PS buttons are active only in the surround mode.
Note
If the CUT ENABLE button is set to OFF, even if you press the CUT button on the CR MONITOR section so that it is lit, the audio signal cannot be cut.
For detailed information on the CR MONITOR section, see page 24.
5SOURCE buttons
These are used to select the signals for control room monitoring. Touch the CR MONITOR tab, then select the desired source for each EXT, AUX, MTR button on the SOURCE section of the Control room section, by touching the corresponding SOURCE buttons.
For the STUDIO LS monitoring, touch the STUDIO LS tab. You can monitor the source selected on the SOURCE buttons.
EXT 1 to EXT 6 buttons: The input routing matrix allows you to assign any input signal to the EXT 1 to 6 channels. When you touch EXT 1 to 6 buttons, you can monitor the signals using the EXT button on the SOURCE section.
When the SURR button is set to ON, you can monitor the signals of EXT 1 to EXT 6.
When the SURR button is set to OFF, you can select one pair among pairs of 1/2, 3/4, and 5/6. It is possible to set both buttons to ON in one pair.
For example, When the EXT 1 button is ON and the EXT 2 is OFF, by touching either the EXT 1 or EXT 2, a pair of EXT 1/2 is selected.
When EXT 1 and EXT 2 buttons are ON and the EXT 6 button is OFF, by touching the EXT 6 button, the pair of EXT 5 and EXT 6 is selected.
In the CR MONITOR section, you can monitor the selected source signals when the EXT button in the SOURCE section of the Control room section is selected.
In the STUDIO LS section, you can monitor the selected source signal by selecting the EXT 1 to 6 button and pressing the SETUP button on the front panel.
AUX 1 to AUX 8 buttons: These buttons allow you to monitor the AUX SEND buses and they operate like the EXT 1 to 6 buttons.
In the CR MONITOR section, you can monitor the signals when the AUX button in the SOURCE section of the Control room section is selected.
In the STUDIO LS section, you can monitor the signal when the SETUP button is selected in the STUDIO LS section on the Master panel.
MTR 1 to MTR 8 buttons: When the SURR button is set to ON, you can monitor the surround sound mixer’s output from the MTR buses 1 to 6. MTR 7 and MTR 8 become one pair. You can select either MTR 1 to MTR 6 or a pair of MTR 7 and MTR 8. In this case, by selecting either MTR 7 or MTR 8, select the pair.
When the SURR button is set to OFF, these buses are selected by pairs of 2 channels as in the case of the EXT buttons.
In the CR MONITOR section, you can monitor the signals when the MTR button in the SOURCE section of the Control room section is selected.
In the STUDIO LS section, you can monitor the signal when the SETUP button is selected in the STUDIO LS section on the Master panel.
PGM button: L and R monitored by selecting the PGM button in the CR and STUDIO LS sections.
6MINI MONITOR buttons
When the SURR button is set to OFF, you can change the output bus of the CR monitor from CR 1/2 to CR 5/6. This button is not active when the SURR button is set to ON.
7PFL buttons
Select how the PFL signal and AFL signal are injected into the monitoring.
A ENBL/DIS button | B ALT/MOM button |
60 Chapter 3 Menu