Technicolor - Thomson SpeedTouchTM620 manual

Chapter 4

SpeedTouch™ Configuration Management

4.2 Configuration Management via Telnet

FTP access

SpeedTouch™ configuration files

For more information on the file system of the SpeedTouch™ and how to access it via FTP, see “7 The SpeedTouch™ File System” on page 75.

The SpeedTouch™’s last saved configuration is stored in the SpeedTouch™ ‘/dl’ subdirectory of the SpeedTouch™ file system.

There may be a user.ini file present in the system’s ‘/active’ subdirectory. However, this user.ini only contains the saved configuration created before your latest software switch-over, and hence may be not up-to-date. Therefore never use this user.ini file for backup reasons.

Full read/write access is only granted in the ‘/dl’ subdirectory.

30	E-DOC-CTC-20051017-0155 v1.0

Image 40

Technicolor - Thomson SpeedTouchTM620 manual Configuration Management via Telnet, FTP access SpeedTouch configuration files

Contents

SpeedTouch620 Page SpeedTouch 620 Trademarks CopyrightDocument Information Contents SpeedTouch Software Modules Integrated SpeedTouch Isdn Modem How to Add an Snmp User 152 How to Restrict Snmp Access 157How to Configure the Traps 158 10.1.1 Basic Concepts 135 10.1.2 MIBs Explained 136 SLA Monitoring Contents About this Operator’s Guide About this Operator’s Guide Introduction Introduction Chapter SpeedTouch Command Line Interface About the CLI Interface CLI web page access requirementsCLI Telnet access requirements CLI serial access requirements CLI Access via Telnet or Serial Console Access via a Telnet session or serial console Basic Navigation Command group navigation=help Or end of a line Going to the beginning=help firewall list Chapter Executing Commands from the Top Level Command Line Interface CommandsFirewall list Executing Commands From the Command Group Chapter Menu-driven CLI Navigation Chapter SpeedTouch System Software About the System Software SpeedTouch System Software System Software Management via FTP Topic See Step Action Backup System Software via FTPFtpcd dl Subdirectory’s contents Software version commandGet the system software file Upgrade or Restore System Software via FTP Upgrade/Restore procedure Software deletepassive command to delete it Use the quote site software version command to checkTransfer system software to the SpeedTouch Ftp put ZZUIAA5.411 Activate the upgrade/ restored system software Mark system software file as Passive Software Version Manual System Software Management via BOOTP/TFTP server System softwareManagement Important note =software upgrade SpeedTouch Configuration Management SpeedTouch Configuration Management Configuration Management via the SpeedTouch Web Interface Configurations via Basic Web Interface Step ActionGo to Home SpeedTouch Configuration Click Save or Restore Configuration SpeedTouch Configuration Management Proceed as follows Restoring configurations via the basic Web InterfaceLocal disk, you want to restore on your SpeedTouch Go to expert mode Click Save All to save the current configurationOpen the Update page via Home SpeedTouch System Update Click Backup Open the Upgrade page via Home SpeedTouch System Update Restoring a configuration via the expert pagesIntend to restore. Select the file and click OK Configuration Management via Telnet FTP access SpeedTouch configuration files Config CLI Command Group Config saveConfig backup filename = user configuration filename Config dump Defaults = noyes Loadip = noyesFlush = yesno Echo = noyes Back up Configurations via FTP SpeedTouch Multi Level Access Policy Configuration GuideSite saveall command Get the latest configuration file from Other configuration files stored via Configuration you saved in is stored in the user.ini fileFtp get user.ini Store Configurations via FTP Introduction Restore/change procedure Quote site saveall command Transfer the configuration file to the SpeedTouchSoftware cleanup CLI command Ftp put config.ini Matches total Ftp quote site config load Connection for /bin/ls Jun 1971 Start.cmd Rwxrwxrwx Template Description SpeedTouch Service TemplatesTemplate files on the SpeedTouch file system Open the Upload File page via Home SpeedTouch System Update SpeedTouch System Languages Management Switch between system languages Go to the Expert Mode Open the language page via Home SpeedTouch System UpdateLanguage Step Action Click on the Language Packs tab Chapter SpeedTouch Software Modules Software Modules ST620 ST608WL ST605SpeedTouch Software Modules Software key Software Activation Key Management Table Item Description =software addon list How to Install a Software Key SpeedTouch System Services Service SeeSpeedTouch System Services Overview This chapter covers the following services SpeedTouch Dynamic DNS SpeedTouch CLI dyndns commands Dyndns serviceDyndns host =dyndns help Example dynamic DNS subscription Adding a dynamic DNS host name Adding a dynamic DNS client=dyndns host add group=MyDynDNSHost name=johndoe.dyndns.org =dyndns add name=MyDynDNS =dyndns modify Name = MyDynDNS Modifying the dynamic DNS clientGroup = MyDynDNSHost Refining the dynamic DNS service settings Service list DNS Service Use multiple hosts configure an additional host=dyndns modify name=MyDynDNS status=enabled Checking dynamic DNS client Resolving SpeedTouch Sntp Client Manual tab Select Manual to Step Action Sntp list Sntp configSntp add and sntp delete Website Filtering Method Description Section See Website Filtering Configuration Pages How to Verify the Filtering Configuration Content level becomes available. Refer to 6.3.3 How to Web Section DescriptionFiltering license is available Information How to Activate a Web Filtering License Configuring the Actions for Uncategorised Sites Filter Priority Actions for Uncategorised Sites How to Create an Address Based Filter How to Create a New Proceed as follows Entry Step ActionGo to the first bullet in the list Address Based Filtering Want to create an entry in the filter How to Create a Content Based Filter Select the content level of your choiceLevel All Legal Teenagers Children BlockAll How to Create a Content Level View Step ActionLevel Step Action Go to the Web site filtering Overview Content Level Step Action Pick a Task... list, select Create a new content level Task Description Intrusion Detection and ProtectionToolbox section, click Intrusion Detection How to Log On To The SpeedTouch Remotely About Remote Assistance How to Set Up Remote AssistanceRemote Assistance Chapter Chapter Opening an FTP session SpeedTouch File SystemTo the SpeedTouch Access rights to the file system Preparing for FTP file transfers Files stored on the file system Ftpcd Chapter SpeedTouch access methods SpeedTouch Remote AccessAccess method System service name Chapter Remote Web Interface Access Configuration via CLI commands=service system list name=HTTP expand=enabled =service system ifadd name=HTTP group=wan = Refinement Service =service system ipadd name=HTTP ip=192.6.11.5 ==service system ipadd name=HTTP ip=192.6.11.0/24 = =service system ipadd name=HTTP ip=192.6.2-55.2-55 = NAT configuration menu, but always in System Services =service system modify name=HTTP state=enabled port=82 = HTTPs service Introduction Secure Remote Web Interface Access=service system list name=HTTPs expand=enabled =service system ifadd name=HTTPs group=wan = =service system ipadd name=HTTPs ip=192.6.11.0/24 = =service system ipadd name=HTTPs ip=192.6.11.5 ==service system ipadd name=HTTPs ip=192.6.2-55.2-55 = =service system modify name=HTTPs state=enabled port=448 = 448 =service system ifadd name=TELNET group=wan = Remote Telnet Access=service system list name=TELNET expand=enabled Refinement of the Service =service system ipadd name=TELNET ip=192.6.11.5 ==service system ipadd name=TELNET ip=192.6.11.0/24 = =service system ipadd name=TELNET ip=192.6.2-55.2-55 = =service system modify name=TELNET state=enabled port=50 = Remote SSH Access SSH service Introduction SSH authentication=ssh config auth=password =ssh config shell=enabled =ssh publickey list =service system list name=SSH expand=enabled SSH =service system ifadd name=SSH group=wan =service system ipadd name=SSH ip=192.6.11.0/24 =service system ipadd name=SSH ip=192.6.11.5=service system ipadd name=SSH ip=192.6.2-55.2-55 =service system modify name=SSH state=enabled port=35 =service system list name=FTP expand=enabled Remote FTP Access=service system ifadd name=FTP group=wan =service system ipadd name=FTP ip=192.6.11.0/24 =service system ipadd name=FTP ip=192.6.11.5=service system ipadd name=FTP ip=192.6.2-55.2-55 =service system modify name=FTP state=enabled port=26 Remote Sftp Access =ssh config sftp=enabled 101 102 103 104 105 LAN Based Auto-Configuration LAC Support TR-064 Configuration Options How to Configure LAC Syntax Disabled Enabled orParameter Descripion Value Description CPE WAN Management Protocol Cwmp Support TR-069 How to Configure Cwmp Syntax Parameter Descripion How to ConfigureParameter Value Description How to Configure the Cwmp Server Syntax Cwmp Server Parameter Description Value 112 Integrated SpeedTouch Isdn Modem Integrated SpeedTouch Isdn ModemOverview This chapter covers the following topics About the Isdn Modem 115 How to Configure the Isdn Modem Isdn Backup Action See How to Configure the Isdn Dial-In Connection Isdn backupClick Connections Click Routed PPoI 119 Enabled or disabled How to Configure the PPP Connection Pap , chap or auto Cidr , dotted or none Enable or disable dial-on-demand Will engage the Isdn backup ifDemanddial DOD. This means that the system Isdn Callback 125 126 Called party must also be set to Support callback 128 129 130 How to Install Remote Proceed as follows Isdn Remote Capi\windows\system32\capi2032.dll RemoteCAPI Select Remote Capi Daemon SpeedTouch Monitoring SpeedTouch Monitoring An Introduction to Snmp Snmp in the SpeedTouch Overview Management Information Base Basic Commands Basic Concepts MIBs Explained RFC1213 MIB-II SpeedTouch Monitoring From previous Standard MIBs MIBs About SnmpRFC3417 Transport Mappings for Snmp MIB RFC3418 SNMPv2-MIB 138 Snmp configuration Task See How to Allow Access to the Snmp Agent How to View the Snmp Configuration About the Snmp ServiceYou can the same command to view the SNMPV3 Traps This returns the following output How to View the System Contact, Name and Location How to Configure SNMPv1 Configure the community to have these group rightsAllow external access to the Snmp agent Create a new community Configure the target parameters Enable trapsCreate a new target Create a notify filter How to Configure the System contact, Name and Location Enable or disableParameters This command has the following parameters Enable or disable the sending How to Force the Source IP Address MTU How to Configure the Snmp Target Parameters The command has the following parameters Destination How to Read Snmp Parameters via the CLI To update the traffic load, useWith objectid the object identity to getNext from To get the iP address table, use Administratorsnmp=walk ObjectId=1.3.6.1.2.1.1 How to Allow Remote Snmp =service system ifadd name SNMPV3AGENT group wan How to Add an Snmp User Group Description Use the following command to create a new view Notification access to that viewUse the following command to create a new user Use the following command to add the user to the group This results in the following output Communities How to Restrict Snmp Access SNMPV3AGENT How to Configure the Traps Use the snmp targetparams add commandUse the snmp notifyfilter add command Use the snmp notifyprofile add command Use the snmp target add command Use the following command sequence SpeedTouch Syslog What is Syslog SpeedTouch Syslog DaemonSpeedTouch Syslog daemon Priority Notation Code 163 Syslog via the Web Interface 165 Syslog CLI command group Syslog via the CLI=syslog help =syslog msgbuf help Remote Syslog Notification =syslog ruleadd fac=all sev=debug dest=192.168.1.10 =saveall =service system list name=SYSLOG expand=enabled Syslog host on a remote network SpeedTouch Identification on AWS Advantages SpeedTouch Identification SpeedTouch Identification over AWS SpeedTouch Advanced Diagnostics About the Advanced Diagnostics Overview Office Network Web 173 174 Opening SpeedTouch Diagnostic Web Interface Diagnostic WebClick... To 176 177 178 Command Line Interface Diagnostics About CLI Diagnostics Accessing the CLIDiagnostical CLI Commands Lower Layer Diagnostics Tmmb Atm debug aal5stats Atm debug gstatsAtm debug portstats Atm oam cc send =autopvc config mode=active = ATM Auto-Configuration via TR-37/ Ilmi=autopvc list Router Services Diagnostics Dhcp client debug statsDhcp server debug stats Dhcp relay debug stats Displays statistics of SpeedTouch’s DNS server/forwarder Dns server debug stats=dns server debug stats Firewall rule debug stats Routing Diagnostics=firewall rule debug stats Below is an example of a ping command and its reply It uses the following parameters Command Below is an example of a traceroute command and its reply Ethernet Diagnostics =eth switch mirror capture port=4 = 190 System debug stats Management DiagnosticsDisplays SpeedTouch cpu and memory statistics 192 SLA Monitoring =sla ping add test=internet addr=11.0.0.138 Parameter Description Values =sla ping start test=internet = =sla ping list Name Description SLA Monitoring Following results will be displayed SLA Traceroute configuration =sla traceroute add test=route addr=11.0.0.138 = 198 =sla traceroute modify test = route Addr = Starting the SLA Traceroute=sla traceroute start test=route = =sla traceroute list Dffield = no Result Info Status =sla traceroute hist test route owner modem 202 Resetting the SpeedTouch Resetting the SpeedTouch=system reboot =system reset factory=yes proceed=yes Switch off the SpeedTouch Press and hold the reset buttonSwitch on the SpeedTouch Keep the reset button pushed in for ca secondsPage Need more help?