Xilinx ML561 Hardware Schematic Diagram

120 www.xilinx.com Virtex-5 FPGA ML561 User Guide

UG199 (v1.2) April 19, 2008

Appendix C: LCD Interface

Tabl e C-1 summarizes the controller specifications.

The on-chip RAM size is 65x 132 = 8580 bits.

Hardware Schematic Diagram

FigureC-1 illustrates the sche matic for the display.

Tabl e C -1 : Display Controller Specifications

Parameter Specification

Supply Voltage 2.4V to 3.6V (VDD)

LCD Driving Voltage 4V to 15V (VLCD=V0-V

DD)

Power Consumption 70μA typical (VDD = 3V, x4 boost, V0 = 11V,

internal supply= ON)

Sleep Mode 2μA

Standby Mode 10μA

Figure C-1: Display Schematic Diagram

3.3V

LCD_D[7:0]

ENA, R/W, RSEL, CS1B

LCD-BUS

DIP1_4

3.3V

Rst Gnd Vcc - +

LED

3.3V

68xx

Default = 68xx

Default =

Resistor to Gnd

Backlight ON/OFF

IC19

IC22

IC23

SamArray

UG199_C_01_050106

Contents

Main Revision History The following table shows the revision history for this document. Table of Contents Preface: About This Guide Chapter 1: Introduction Chapter 2: Getting Started Chapter 3: Hardware Description Chapter 4: Electrical Requirements Chapter 5: Signal Integrity Recommendations Chapter 6: Configuration Chapter 7: ML561 Hardware-Simulation Correlation Appendix A: FPGA Pinouts Appendix B: Bill of Materials Appendix C: LCD Interface General Display Hardware Design Hardware Schematic Diagram Page Preface About This Guide Guide Contents Additional Documentation Additional Support Resources Conventions Conventions This document uses the following conventions. An example illustrates each convention. Typographical This document uses the following typographical conventions. An example illustrates each convention. Online Document Preface: About This Guide Chapter 1 Introduction About the Virtex-5 FPGA ML561 Memory Interfaces Tool Kit Virtex-5 FPGA ML561 Memory Interfaces Development Board Page Page Chapter 2 Getting Started Documentation and Reference Design CD Initial Board Check Before Applying Power Applying Power to the Board Chapter 3 Hardware Description Hardware Overview FPGA USB VTT & VREF FPGA #3 Figure 3-1: ML561 XC5VLX50T-FFG1136 Board Placement Diagram Memories DDR400 SDRAM Components DDR2 DIMM DDR2 SDRAM Components QDRII SRAM RLDRAM II Devices Memory Details DDR400 and DDR2 Component Memories Figure 3-3: FPGA #1 Banks for DDR400 and DDR2 Component (Top View) Page DDR2 SDRAM DIMM Figure 3-4: FPGA #2 Banks for DDR2 DIMM (SSTL18) Interfaces (Top View) Table 3-5: DDR2 DIMM Signal Summary QDRII and RLDRAM II Memories Figure 3-5: FPGA #3 Banks for QDRII SRAM and RLDRAM II Interfaces (Top View) Page External Interfaces RS-232 USB Clocks 200 MHz LVPECL Clock SMA Clock 33 MHz Clock 33 MHz System ACE Controller Oscillator GTP Clocks User I/Os General-Purpose Headers DIP Switch Seven-Segment Displays Light Emitting Diodes (LEDs) Pushbuttons Power On or Off Slide Switch Soft Touch Probe Points Power Measurement Header Liquid Crystal Display Connector Power Regulation Figure 3-8: LCD Panel Connector for Possible LCD Support Figure 3-9: Virtex-5 FPGA ML561 Development Board Power Distribution System Power R egulati on Power D istri bution Voltage Regulators PTH05010 Voltage Regulator Page Board Design Considerations Page Page Chapter 4 Electrical Requirements Power Consumption Table 4-1: ML561 Power Consumption Table 4-1: ML561 Power Consumption (Continued) Page Page Page Table 4-3: ML561 Power Plane Capacities (Continued) FPGA Internal Power Budget Chapter 5 Signal Integrity Recommendations Termination and Transmission Line Summaries Chapter 5: Signal Integrity Recommendations Table 5-1: DDR400 SDRAM Component Terminations Table 5-2: DDR2 SDRAM DIMM Terminations Table 5-3: DDR2 SDRAM Component Terminations Termination and Transmission Line Summaries Table 5-4: QDRII SRAM Terminations Table 5-5: RLDRAM II Terminations Page Chapter 6 Configuration Configuration Modes JTAG Chain JTAG Port Parallel IV Cable Port System ACE Interface System ACE Interface Page Chapter 7 ML561 Hardware-Simulation Correlation Introduction Test Setup Page Signal Integrity Correlation Results DDR2 Component Write Operation Figure 7-3: Post-Layout IBIS Schematics of DDR2 Component Write Data Bit (DDR2_DQ_BY2_B3) Table 7-1: Circuit Elements of DDR2 Component Write Data Bit (DDR2_DQ_BY2_B3) Table 7-2: DDR2 Component Write Operation Correlation Results Page Figure 7-4: DDR2 Component Write HW Measurement - Eye Scope Shot at Probe Point (DDR2 Memory Via) Figure 7-5: DDR2 Component Write Correlation - Eye Scope Shot at Probe Point (Slow Corner) Page Figure 7-8: DDR2 Component Write Extrapolation - Eye Scope Shot at Receiver IOB (Slow Corner) Figure 7-9: DDR2 Component Write Extrapolation - Waveform Scope Shot at Receiver IOB (Slow Corner) Virtex-5 FPGA ML561 User Guide www.xilinx.com 63 Figure 7-10: DDR2 Component Write Extrapolation - Eye Scope Shot at Receiver IOB (Fast Corner) Figure 7-11: DDR2 Component Write Extrapolation - Waveform Scope Shot at Receiver IOB (Fast Corner) 64 www.xilinx.com Virtex-5 FPGA ML561 User Guide DDR2 Component Read Operation Figure 7-12: Post-Layout IBIS Schematics of the DDR2 Component Read Data Bit (DDR2_DQ_BY2_B3) Table 7-4: Circuit Elements of DDR2 Component Read Data Bit (DDR2_DQ_BY2_B3) Table 7-5: DDR2 Component Read Operation Correlation Results Figure 7-13: DDR2 Component Read HW Measurement - Eye Scope Shot at Probe Point (FPGA1 Via) Figure 7-14: DDR2 Component Read Correlation - Eye Scope Shot at Probe Point (Slow Corner) Page Figure 7-17: DDR2 Component Read Extrapolation - Eye Scope Shot at Receiver IOB (Slow Corner) Time (ns) Figure 7-18: DDR2 Component Read Extrapolation - Waveform Scope Shot at Receiver IOB (Slow Corner) 68 www.xilinx.com Virtex-5 FPGA ML561 User Guide Figure 7-19: DDR2 Component Read Extrapolation - Eye Scope Shot at Receiver IOB (Fast Corner) Figure 7-20: DDR2 Component Read Extrapolation - Waveform Scope Shot at Receiver IOB (Fast Corner) Virtex-5 FPGA ML561 User Guide www.xilinx.com 69 DDR2 DIMM Write Operation UG199_c7_21_071907 Figure 7-21: Post-Layout IBIS Schematics of DDR2 DIMM Write Data Bit (DDR2_DIMM_DQ_BY2_B3) Table 7-6: Circuit Elements of DDR2 DIMM Write Data Bit (DDR2_DIMM_DQ_BY2_B3) Table 7-7: DDR2 DIMM Write Operation Correlation Results Table 7-8: DIP[1:2] Settings Figure 7-22: DDR2 DIMM Write HW Measurement - Eye Scope Shot at Probe Point #1 (DDR2 Memory Via) Figure 7-23: DDR2 DIMM Write Correlation - Eye Scope Shot at Probe Point #1 (Slow Corner) Page Figure 7-26: DDR2 DIMM Write Extrapolation - Eye Scope Shot at Receiver IOB (Slow Corner) Figure 7-27: DDR2 DIMM Write Extrapolation - Waveform Scope Shot at Receiver IOB (Slow Corner) 74 www.xilinx.com Virtex-5 FPGA ML561 User Guide Figure 7-28: DDR2 DIMM Write Extrapolation - Eye Scope Shot at Receiver IOB (Fast Corner) Figure 7-29: DDR2 DIMM Write Extrapolation - Waveform Scope Shot at Receiver IOB (Fast Corner) Virtex-5 FPGA ML561 User Guide www.xilinx.com 75 DDR2 DIMM Read Operation Figure 7-30: Post-Layout IBIS Schematics of the DDR2 DIMM Read Data Bit (DDR2_DIMM_DQ_B) Table 7-9: Circuit Elements of DDR2 DIMM Read Data Bit (DDR2_DIMM_DQ_BY2_B3) Table 7-10: DDR2 DIMM Read Operation Correlation Results Figure 7-31: DDR2 DIMM Read HW Measurement - Eye Scope Shot at Probe Point (FPGA1 Via) Figure 7-32: DDR2 DIMM Read Correlation - Eye Scope Shot at Probe Point (Slow Corner) Figure 7-33: DDR2 DIMM Read HW Measurement - Waveform Scope Shot at Probe Point (FPGA1 Via) Figure 7-34: DDR2 DIMM Read Correlation - Waveform Scope Shot at Probe Point (Slow Corner) Figure 7-35: DDR2 DIMM Read Extrapolation - Eye Scope Shot at Receiver IOB (Slow Corner) Figure 7-36: DDR2 DIMM Read Extrapolation - Waveform Scope Shot at Receiver IOB (Slow Corner) Virtex-5 FPGA ML561 User Guide www.xilinx.com 79 Figure 7-37: DDR2 DIMM Read Extrapolation - Eye Scope Shot at Receiver IOB (Fast Corner) Figure 7-38: DDR2 DIMM Read Extrapolation - Waveform Scope Shot at Receiver IOB (Fast Corner) 80 www.xilinx.com Virtex-5 FPGA ML561 User Guide QDRII Write Operation Figure 7-39: Post-Layout IBIS Schematics of QDRII Write Data Bit (QDR2_D_BY0_B5) Table 7-11: Circuit Elements of QDRII Write Data bit (QDR2_D_BY0_B5) Table 7-12: QDRII Write Operation Correlation Results Figure 7-40: QDRII Write HW Measurement - Eye Scope Shot at Probe Point (QDRII Memory Via) Figure 7-41: QDRII Write Correlation - Eye Scope Shot at Probe Point (Slow Corner) Figure 7-42: QDRII Write HW Measurement - Waveform Scope Shot at Probe Point (QDRII Memory Via) Figure 7-43: QDRII Write Correlation - Waveform Scope Shot at Probe Point (Slow Corner) Figure 7-44: QDRII Write Extrapolation - Eye Scope Shot at Receiver IOB (Slow Corner) Figure 7-45: QDRII Write Extrapolation - Waveform Scope Shot at Receiver IOB (Slow Corner) 84 www.xilinx.com Virtex-5 FPGA ML561 User Guide Figure 7-46: QDRII Write Extrapolation - Eye Scope Shot at Receiver IOB (Fast Corner) Figure 7-47: QDRII Write Extrapolation - Waveform Scope Shot at Receiver IOB (Fast Corner) Virtex-5 FPGA ML561 User Guide www.xilinx.com 85 QDRII Read Operation Figure 7-48: Post-Layout IBIS Schematics of QDRII Read Data Bit (QDR2_Q_BY0_B5) Table 7-13: Circuit Elements of QDRII Read Data Bit (QDR2_Q_BY0_B5) Table 7-14: QDRII Read Operation Correlation Results Figure 7-49: QDRII Read HW Measurement - Eye Diagram Scope Shot at Probe Point (FPGA3 Via) Figure 7-50: QDRII Read Correlation - Eye Diagram Scope Shot at Probe Point (Slow Corner) Figure 7-51: QDRII Read HW Measurement - Waveform Scope Shot at Probe Point (FPGA3 Via) Figure 7-52: QDRII Read Correlation - Waveform Scope Shot at Probe Point (Slow Corner) Figure 7-53: QDRII Read Extrapolation - Eye Scope Shot at Receiver IOB (Slow Corner) Figure 7-54: QDRII Read Extrapolation - Waveform Scope Shot at Receiver IOB (Slow Corner Virtex-5 FPGA ML561 User Guide www.xilinx.com 89 Figure 7-55: QDRII Read Extrapolation - Eye Scope Shot at Receiver IOB (Fast Corner) Figure 7-56: QDRII Read Extrapolation - Waveform Scope Shot at Receiver IOB (Fast Corner) 90 www.xilinx.com Virtex-5 FPGA ML561 User Guide Summary and Recommendations Page How to Generate a User-Specific FPGA IBIS Model Page Appendix A FPGA Pinouts FPGA #1 Pinout Page Page Page FPGA #1 Pinout FPGA #2 Pinout Tabl e A-2 lists the connections for FPGA #2 (U5). Table A-2: FPGA #2 Pinout Page Page Page Page Page Page Page FPGA #3 Pinout Tabl e A-3 lists the connections for FPGA #3 (U34). Table A-3: FPGA #3 Pinout Page Page Page Page Page Page Appendix B Bill of Materials Appendix B: Bill of Materials Table B-1: Bill of Materials (Continued) Page Appendix C LCD Interface General Display Hardware Design Tabl e C-1 summarizes the controller specifications. The on-chip RAM size is 65x 132 = 8580 bits. Hardware Schematic Diagram Tabl e C -1 : Display Controller Specifications Peripheral Device KS0713 FigureC-2 is a block diagram of t he Samsung KS0713. KS0713 Samsung Figure C-2: KS0713 Block Diagram Controller Figure C-4: 64128EFCBC-XLP Dimensions Figure C-3: 64128EFCBC-XLP Block Diagram 128 x 64 DOTS FigureC-4 shows the dimensions for the 64128EFCBC-XLP LCD panel. Controller Operation Table C-2: LCD Panel (Continued) Controller LCD Panel Connections Table C-2: LCD Panel (Continued) Controller Power Supply Circuits Operation Example of the 64128EFCBC-3LP Page Page Instruction Set Tabl e C-6 shows the instruction set for the LCD panel. Table C-6: Display Instructions Page Table C-6: Display Instructions (Continued) Read/Write Characteristics (6800 Mode) Figure C-7: Read/Write Timing Waveforms (6800 Mode) Design Examples LCD Panel Used in Full Graphics Mode LCD Panel Used in Character Mode Display Command Byte Display Data Byte Figure C-10: Block RAM Organization Page Array Connector Numbering