Skil 3700 manual Using the Rip Fence

Page 76

Using the Rip Fence

RIPPING, BEVEL RIPPING, RESAWING AND RABBETING are performed using the RIP FENCE together with the AUXILIARY FENCE / WORK SUPPORT, PUSH STICK OR PUSH BLOCK.

!For your own safety, always observe the WARNING following safety precautions in addition to

the safety instructions on Pages 4-10.

1.Never make these cuts FREEHAND (without using the rip fence or auxiliary devices when required) because the blade could bind in the cut and cause a KICKBACK.

2.Always lock the rip fence securely when in use.

3.Remove miter gauge from table during any operations which utilize the rip fence.

4.Make sure blade guard is installed for all thru-sawing type cuts. Replace the guard IMMEDIATELY following completion of resawing, rabbeting, dadoing or molding operations.

Frequently check the action of the ANTIKICKBACK PAWLS by passing the workpiece alongside of the spreader while saw is OFF.

Pull the workpiece TOWARD you. If the PAWLS do not DIG into the workpiece and HOLD it, the pawls must be REPLACED. See “Maintenance” on Page 108.

5.Have blade extend approximately 1/8" above top of workpiece. Additional blade exposure would increase the hazard potential.

6.Do not stand directly in front of the blade in case of a KICKBACK. Stand to either side of the blade.

7.Keep your hands clear of the blade and out of the path of the blade.

8.If the blade stalls or stops while cutting, TURN SWITCH OFF before attempting to free the blade.

9.Do not reach over or behind the blade to pull the workpiece through the cut to support long or heavy workpieces to remove small cut-off pieces of material or FOR ANY OTHER REASON.

10.Do not pick up small pieces of cut-off material from the table. REMOVE them by pushing them OFF the table with a long stick. Otherwise they could be thrown back at you by the rear of the blade.

11.Do not remove small pieces of cut-off material that may become TRAPPED inside the blade guard while the saw is RUNNING. THIS COULD ENDANGER YOUR HANDS or cause a KICKBACK. Turn the saw OFF. After the blade has stopped turning, lift the guard and remove the piece.

12.If workpiece is warped, place the CONCAVE side DOWN. This will prevent it from rocking while it is being ripped.

Note: See pages 5-7 for Table Saw Specific Safety Rules.

						º
						45
						º
						40
						5º
					º	3
					30
				20º	25º
			15º	20º
	5º	10º	15º
0º	5º	10º

FIG. 56

76.

Image 76

Contents 3700 Table of Contents Glossary of Terms General Safety Rules Personal SafetyWork Area Tool UseBasic Operation and Set Up Table Saw Specific Safety RulesTool Care Rip Cutting Cross CuttingPlunge Cutting Dragged into the blade during a kickbackShop Safety Rules Accessory Power OutletNon-Through Cutting Dado, Rabbet, Resawing KickbackSander Safety Router Table SafetyThrowing fragments Jigsaw Safety Double Insulated Tools Grounded ToolsExtension Cords Replace damaged cords immediatelyPage Utilisation des accessoires X-Shop avec Table des matières« Conservez CES Instructions » Informations relatives à la sécuritéLexique Consignes générales de sécurité Zone de travailSécurité de l’utilisateur Utilisation de l’outilConsignes de sécurité pour les scies de table Protection de l’outilUtilisation et réglages élémentaires Prenez Soin DE VOS Outils ET ENTRETENEZ-LES BienSciage en travers RefenteSciage en plongée Consignes de sécurité pour X-Shop Coupes non débouchantes Rainures, feuillures, dédoublementCoincera le matériau et risquera de causer un rebond Consignes de sécurité pour une table à toupieDe causer une perte de contrôle Consignes de sécurité Pour une scie à chantourner Outils à double isolation Outils mis à la terreCordons de rallonge En la matièreÉtiquettes d’avertissement Pour Continuation DU FRANÇAIS, REPORTEZ-VOUS À LAÍndice Guarde Estas InstruccionesGlosario de términos Normas generales de seguridad Area de trabajoSeguridad personal Utilización de la herramientaCuidado de la herramienta Funcionamiento y preparación básicosEvite LAS Areas DE Gases Mantenga LAS Herramientas CON CuidadoCorte transversal Corte al hiloCorte por penetración Corte no pasante De mortaja, rebajo o reaserrado Sea consciente de la proximidad de la mano y los dedos a laInstrucciones de seguridad para mesas de fresadora Podría causar una pérdida de controlInstrucciones de seguridad Para sierras caladoras Herramientas con aislamiento doble Herramientas conectadas a tierraCordones de extensión Conserve Estas InstruccionesEtiquetas de advertencia VER Continuación DEL Español EN LA PáginaUnpacking Checking Contents Pièces détachées dans le carton Piezas sueltas contenidas en la caja de cartónCabinet P Arts Assembly KitsSmall parts Kits de montage Juegos de ensamblajes Ensemble du coffret Ensamblaje del armarioHardware Kit Jigsaw Insert Hardware Kit Sander InsertHardware Kit Blank Insert Guide de ponceuse Guide de toupie Plaquette amovible pour ponceuseTope-guía de lijadora Tope-guía de fresadora Juego de ensamblaje de sierraTools Needed For Assembly Hardware Kit Router InsertOutils nécessaires à l’assemblage Herramientas necesarias para el ensamblajePlaquette amovible pour toupie Juego de herrajes del accesorioAssembly Assembling CabinetAssemblage du coffret AssemblageEnsamblajeEnsamblaje del armario C16 C19 C17 Assemblage du coffret suite Ensamblaje del armario continuaciónAttaching Wings Attaching Front RailsMontage des ailes Montage du rail avantEnsamblaje de las alas Colocación del riel delanteroAttaching Handle To Rip Fence Attaching Digital DisplayT18 Colocación del mango en El tope-guía para cortar al hilo Montage de l’écran ’affichage numériqueAttach handle to wheel using bolt as shown in figure Attaching Handle to Elevation WheelMontage du guide de refente Réglage de hauteurColocación del tope-guía Para cortar al hilo Colocación del mango en el rueda de ElevacionAttaching Blade Guard Colocación del protector de la hoja Montage du protège-lamePerno hexagonal de 1/4-20 x 2 pulg Attaching Blank Insert Wings and blank insert must be installedOrder to use the table saw. Wings and blank Montage de l’ébauche de plaquette amovible Attaching Router Insert Outil non joint / Herramienta no incluidaMontage de la plaquette Amovible pour toupie ’emploi qui accompagne la toupieArt Description Instrucciones que vino con la fresadoraAttaching Sander Insert Montage de la plaquette amovible pour ponceuse De instrucciones que vino con la lijadoraAttaching Jigsaw Insert Montage de la plaquette amovible Pour scie à chantourner Colocación del accesorio De inserción de sierra caladoraGetting To Know Your Shop Outils X-Shop Taller convertible X-ShopAccessory Tool Inserts Wrench StorageRIP Fence Storage Cord WrapRangement DES Clés Rangement DU Guide DE RefenteRangement DU Guide DE Coupe Angulaire Rangement DU CordonMiter Gauge Router not includedSander not included Jigsaw not includedPlaquettes Amovibles Pour Accessoires Guide DE Coupe AngulaireAccesorios DE Inserción Para Herramientas Calibre DE IngletesTable Saw Adjustments Adjusting 90 and 45 Degree Positive StopsAdjusting Positive Stop AT 90 Degrees Adjusting Positive Stop AT 45 DegreesRéglage des butées positives 90 et 45 degrés Control de inclinación de la hojaAjuste de los topes positivos 90 y 45 grados Para el calibre de ingletesAdjusting Blade Parallel To Miter Gauge Slots Changing The BladeRemplacement de la lame Cambio de la hojaDe changer la lame De cambiar las hojasManual Pointer Adjustment Miter Gauge AdjustmentShop Tools Adjustments Aligning Rip FenceAlignement du guide de refente Réglage manuel de l’aiguilleAlineación del tope-guía Para cortar al hilo Ajuste manual del indicadorTable Saw Power Switch Using the Miter Gauge with T BarUsing The Miter Gauge Basic Table Saw OperationUtilización básica De la sierra de mesa Push Stick and Push Block Work HelpersAuxiliary Fence Accessoires de sciage Ayudantes de trabajoPalo de empujar y bloque de empujar Guide auxiliaireUsing the Rip Fence Utilización del tope-guía Para cortar al hilo Utilisation du guide de refentePour votre propre sécurité Operating the Digital Display Error MessagesRipping Mensajes DE Error RefenteCorte al hilo Messages D’ERREURBevel Ripping CrosscuttingRefente biseautée Coupe transversaleCorte al hilo en bisel Corte transversalRepetitive Cutting Miter CuttingBevel Crosscutting Compound Miter CuttingCoupes à répétition Coupe angulaireCoupe transversale biseautée Coupe angulaire combinéeMaking a Featherboard Non Thru-SawingRabbeting Sciage non débouchant FeuillureAserrado no pasante Elaboración de una tabla De canto biseladoResawing Dado CuttingSpecial Cutting Techniques Rainure Corte de mortajasCoupe à dédoublement Techniques de coupe spécialesUsing X-Shop Accessories With Inserts Never leave the power tool unattended while it isOff position Running or before it comes to a complete stopAvant qu’il ne soit complètement à l’arrêt De apagadoTo Adjust the Fence Opening for Router BIT Clearance FIG To Adjust the Depth of CUT FIGTo Adjust the Router BIT Height Installing the Router BIT Positioning the GuardUtilisation de la toupie X-Shop Utilización de la fresadora X-ShopRouting Using the Feather Board Using the Feather Board on Table TOPUsing the Feather Board On the Fence Figure Fence Location and Workpiece FeedSUR LE Dessus DE LA Table SUR LE Guide FigureSobre EL Tablero DE LA Mesa Sobre EL TOPE-GUÍA FiguraRouting Using the Fence Jointing Full Edge CuttingJunteo Corte DE Bordes Completos Installez une mèche droite dans la toupieInstale una broca recta en la fresadora Edge Cutting with NON-PILOTED Router Bits Edge Cutting with Piloted Router BitsInstallez la mèche désirée dans la toupie NON PilotéesSIN Punta Piloto Toupie PilotéesGROOVING, FLUTING, and Veining Création DE RAINURES, D’ENTAILLES ET DE Veinures RANURADO, Estriado Y AcanaladoShop Sander Operation Pinching or entrapment of fingersUtilisation de la ponceuse X-Shop Utilización de la lijadora X-ShopShop Jigsaw Operation Utilización de la sierra caladora X-Shop Maintaining Your Shop MaintenanceLubrication Mantenimiento de la sierra De mesa X-Shop MantenimientoLubrification LubricaciónRecommended Accessories Use only recommended accessories. FollowInstructions that accompany accessories Use of improper accessories may cause hazardsAccesorios recomendados Trouble Shooting Guide de diagnosticLocalización y reparación De averías Averia LA Sierra no Arranca110 RemarquesNotas Limited Warranty of Skil Benchtop Tools