Kickbacks can cause serious injury. A “KICKBACK” occurs when a part of the workpiece binds between the blade and the rip fence or other fixed object. Workpiece binding the blade due to misalignment can also cause kickback. During kickback, workpiece rises from table and is thrown rapidly back toward the operator. Keep your face and body to one side of the blade, out of line with a possible “KICKBACK”.
In general, some simple procedures and setups can usually avoid kickbacks and possible injury:
Adjust the blade so that it is parallel to the miter gauge slots on the table then adjust the fence so that it is parallel to the blade. Do not use miter gauge and rip fence together in cutting operations. A misaligned fence, miter gauge or these two devices used together could cause the workpiece to become like a wedge and bind the spinning blade.
Always use the guard for every through cutting operation. The guard system (hood, splitter and anti- kickback pawls) is designed to reduce the intensity of a kickback and keep your hands away from the spinning blade.
When using a push stick or block the trailing end of the work must be square. A push stick or block against an uneven end can slip off or push the work away from fence.
Keep the saw blade clean and sharp. Dull and sticky blades will increase the tendency to bind in the workpiece.
Do not trap or confine the
Do not position your hands or fingers in the path of the blade. You may slip into the blade if you apply uneven or excessive force. You can be dragged back into the blade during a kickback.
Push the workpiece through against the rotation of the blade. Never feed material from the back of the saw as the blade can launch the workpiece at great velocity across the tabletop.
Never pull the work through the blade. Start and finish the cut from the operator side (switch side) of the table saw.
Stand to the side of the blade and workpiece; never stand directly in line. During a kickback the workpiece will be rapidly projected from the table saw.
Never cut more than one workpiece at a time. Stacked workpieces can shift or bind on the easily and lead to unexpected contact with blade.
Never reach in back of the blade during operation or until the blade has come to a complete stop. You may be
dragged into the blade during a kickback.
Rip Cutting
Always set and maintain the rip fence parallel to the saw blade. A misaligned fence could cause the workpiece to become like a wedge and bind the spinning saw blade.
Set blade height for through cutting to just above the workpiece thickness. Minimizing exposure of blade body will reduce the tendency of blade binding on body of saw blade.
Keep hood guard assembly, spreader and
Check their action before ripping. The spreader aligned with the saw blade and the pawls are intended to stop a kickback once it has started.
Feed force must be applied only between fence and blade. Never apply pressure to the side of the blade. Pressure applied to the side of the blade will cause the blade to stall or kickback the workpiece.
When performing a bevel rip cut, always place the fence to the right of the blade. On this particular table saw the blade tilts to the left. Bevel ripping with the fence on the left side may not allow the use of the push stick and will wedge the workpiece between the blade and the fence.
Be aware of increased blade exposure on the right side of the guard, when setting the blade for bevel angle. Pay
attention to the proximity of your fingers to blade.
Never cut freehand! Use the fence to support the length of the workpiece in ripping cuts and the miter gauge for cross cut operations. Unsupported or improperly supported workpieces may bind and kickback.
Never attempt to pull the workpiece through the spinning saw blade. You may experience a kickback and be dragged into spinning saw blade.
Do not release work until you have pushed it all the way past the saw blade. Keep your hands away from side and to the rear of a spinning saw blade. A kickback can drag your hand into the blade if it is positioned on the workpiece, to the side or behind the blade.
Use a Push Stick for ripping widths of 2" to 6" and an auxiliary fence and Push Block for ripping widths narrower than 2". When ripping, apply the feed force to the section of the workpiece between the saw blade and the rip fence. If your hand or fingers are within 6 inches of the spinning blade you are too close to be able to react in case of a kickback event and you may be injured.
Never
Do not rip workpiece that is twisted or warped or does not have a straight edge to guide along the rip fence. Workpieces without a straight edge will tend to wedge themselves between blade and fence possibly causing a kickback.
Cross Cutting
Whether performing straight cross cutting or miter angle cross cutting operations, always follow these warnings:
When cross cutting, never use the rip fence and the miter gauge together. They will act against each other and bind the work on the blade leading to kickback.
Use the guard system for the cross cuts. The guard is not
just for rip cutting.
If the workpiece is too small, affix a jig or other means to fix workpiece to miter gauge during a cross cut operation. This lets you properly hold the miter gauge and workpiece while keeping your fingers away from blade.
Plunge Cutting
Never attempt to plunge cut into a workpiece by placing it on top of the spinning blade. The workpiece will kickback.
6.