Anritsu S331D, S332D manual Site Master PM

51)Power Meter Relative

52)Power Meter Relative

53)Power Meter Relative (lowest byte)

54)Power Meter Status (00h = Off, 01h = On)

55)Power Meter Unit (00h = Watts, 01h = dBm)

56)Power Meter Relative Status (00h = Off, 01h = On)

57)Power Meter Offset Status (00h = Off, 01h = On)

58)Power Meter RMS Averaging Level (00h = Off, 01h = Low, 02h = Medium, 03h = High)

59)Frequency Scale Factor135 (higher byte)

60)Frequency Scale Factor (lower byte)

61)Frequency Range Minimum136 (highest byte)

62)Frequency Range Minimum

63)Frequency Range Minimum

64)Frequency Range Minimum (lowest byte)

65)Frequency Range Maximum137 (highest byte)

66)Frequency Range Maximum

67)Frequency Range Maximum

68)Frequency Range Maximum (lowest byte)

69)Zero Status (00h = Off, 01h = On)

70)Zero Value138 (highest byte)

71)Zero Value

72)Zero Value

73)Zero Value (lowest byte)

74-120) Not Used

For T1 Mode (Option 50):

26)T1 Receive Input (00h: Terminate, 01h: Bridged, 02h: Monitor)

27)T1 Framing Mode (01h: ESF, 02h: D4SF)

28)T1 Line Coding (01h: B8ZS, 02h: AMI)

29)T1 Clock Source (00h: External, 01h: Internal)

30)T1 Tx Level (01h: 0 dB, 02h: -7.5 dB, 03h: -15 dB)

31)T1 Error Insert Type (00h: Frame Error, 01h: BPV, 02h: Bit Errors, 04h: RAI, 05h: AIS)

32)T1 Loop Code (00h: CSU, 01h: NIU, 02h: User 1, 03h: User 2)

33)T1 CRC Method (00h: ANSI CRC, 01h: Japanese CRC)

34)T1 Loop Type (00h: In Band, 01h: Data Link)

35)T1 Pattern (higher byte)

36)T1 Pattern (lower byte) 01h: PRBS-9, 02h: PRBS-11, 03h: PRBS-15, 04h: PRBS-20(O.151), 05h:

PRBS-20(O.153), 06h: PRBS-23, 07h: QRSS, 08h: 1 in 8, 09h: 2 in 8, 0Ah: 3 in 8, 0Bh: All Ones, 0Ch: All

Zeros, 0Dh: T1-DALY, 0Eh: User Defined)

37)T1 Pattern Invert Status (00h: Non-Inverted, 01h: Inverted)

38)T1 Display Type (00h: Histogram, 01h: Raw Data)

39)T1 Impedance

40 - 55) First User Defined Loop Code Down (16 bytes)

56 - 71) Second User Defined Loop Code Down (16 bytes)

72 - 87) First User Defined Loop Code Up (16 bytes)

88 - 103) Second User Defined Loop Code Up (16 bytes)

104 - 135) User Defined Pattern (32 bytes)

136) T1 1st User Defined Loop Up (higher byte)

135In number of Hz

136Scaled by Frequency Scale Factor

137Scaled by Frequency Scale Factor

138Value sent as ((value in dBm ￿ 1000) + 100)

46 Site Master PM