95)Channel Selection (lower byte)

96)Frequency Scale Factor201 (higher byte)

97)Frequency Scale Factor (lower byte)

98)Frequency Range Minimum202 (highest byte)

99)Frequency Range Minimum

100)Frequency Range Minimum

101)Frequency Range Minimum (lowest byte)

102)Frequency Range Maximum203 (highest byte)

103)Frequency Range Maximum

104)Frequency Range Maximum

105)Frequency Range Maximum (lowest byte) 106 – 150) Not Used

151)Power Meter Reading204 (highest byte)

152)Power Meter Reading

153)Power Meter Reading

154)Power Meter Reading (lowest byte)

For T1 Tester / E1 Tester Mode (Option 50):

57)Receive Input (00h: Terminate, 01h: Bridged, 02h: Monitor)

58)Framing Mode205

59)Line Coding (01h: B8ZS, 02h: AMI, 03h: HDB3)

60)Tx Level (Valid for T1 Only) (01h: 0 dB, 02h: -7.5 dB, 03h: -15 dB)

61)Clock Source (00h: External, 01h: Internal)

62)Error Insert Type (00h: Frame Error, 01h: BPV, 02h: Bit Errors, 04h: RAI, 05h: AIS)

63)Loop Code (Valid for T1 Only) (00h: CSU, 01h: NIU, 02h: User 1, 03h: User 2)

64)Loop Type (Valid for T1 Only) (00h: In Band, 01h: Data Link)

65)CRC Method (Valid for T1 Only) (00h: ANSI CRC, 01h: Japanese CRC)

66)Display Type (00h: Histogram, 01h: Raw Data)

67)Impedance (Valid for E1 Only) (01h: 75￿, 02h: 120￿)

68)Pattern206

69)Pattern Invert Status (00h: Non-Inverted, 01h: Inverted)

70)Insert Bit Error Value (1-1000) (higher byte)

71)Insert Bit Error Value (lower byte)

72)Insert BPV Error Value (1-1000) (higher byte)

73)Insert BPV Error Value (lower byte)

74)Insert Frame Error Value (1-1000) (higher byte)

75)Insert Frame Error Value (lower byte)

76)Measurement Duration207

77)Histogram Resolution208

78)Frame Sync Status (00h: In Sync, 01h: Out-of-Sync)

201In number of Hz

202Scaled by Frequency Scale Factor (bytes 96-97)

203Scaled by Frequency Scale Factor (bytes 96-97)

204Power sent as (power in dBm * 1000). Use two’s-complement method to decode negative power levels.

205T1 Mode: 01h: ESF, 02h: D4SF

E1 Mode: 03h: PCM30, 04h: PCM30CRC, 05h: PCM31, 06h: PCM31CRC

206Pattern: 01h: PRBS-9, 02h: PRBS-11, 03h: PRBS-15, 04h: PRBS-20(O.151), 05h: PRBS-20(O.153), 06h: PRBS-23, 07h: QRSS, 08h: 1 in 8, 09h: 2 in 8, 0Ah: 3 in 8, 0Bh: All Ones, 0Ch: All Zeros, 0Dh: T1-DALY, 0Eh: User Defined

207Measurement Duration: 00h: Manual, 01h: 3 min, 02h: 15 min, 03h: 30 min, 04h: 1 hr, 05h: 3 hrs, 06h: 6 hrs, 07h: 12 hrs, 08h: 1 day, 09h: 2 days

208Histogram Resolution: 00h: Auto, 01h: 1 sec, 02h: 15 sec, 03h: 30 sec, 04h: 45 sec, 05h: 1 min, 06h: 15 min, 07h: 30 min, 08h: 45 min, 09h: 60 min

Site Master PM

59

Page 65
Image 65
Anritsu S332D, S331D manual Site Master PM