292) Status Byte 1: ( 0b = Off , 1b = On)
(LSB) | bit 0 : Marker 1 On/Off |
| bit 1 : Marker 2 On/Off |
| bit 2 : Marker 3 On/Off |
| bit 3 : Marker 4 On/Off |
| bit 4 : Marker 5 On/Off |
| bit 5 : Marker 6 On/Off |
| bits |
293) Status Byte 2: ( 0b = Off , 1b = On) | |
(LSB) | bit 0 : Not Used |
| bit 1 : Marker 2 Delta On/Off |
| bit 2 : Marker 3 Delta On/Off |
| bit 3 : Marker 4 Delta On/Off |
| bit 4 : Pre Amp Mode (0b = Manual, 1b = Auto) |
| bit 5 : Pre Amp Status On/Off |
| bit 6 : Dynamic Attenuation On/Off |
| bit 7: Reserved |
294) Status Byte 3: (0b = Off, 1b = On) | |
(LSB) | bit 0 : Antenna Factor Correction On/Off |
| bits |
| bits |
| (Linear) – 00b = Watts 01b = Volts |
bit 5 | : Channel Power On/Off |
bit 6 | : Adjacent Channel Power On/Off |
bit 7 | : Units Type (0b = Log 1b = Linear) |
295) Status Byte 4170
(0b = Off/Beep if data is BELOW line, 1b = On/Beep if data is ABOVE line) (LSB) bit 0 : Limit Type (0b = Single, 1b = Multiple)
bit 1 : Not Used
bit 2 : Single Limit On/Off
bit 3 : Single Limit Beep Level ABOVE/BELOW
bit 4 : Multiple Limit Upper Segment 1 Status On/Off
bit 5 : Multiple Limit Upper Segment 1 Beep Level ABOVE/BELOW171
bit 6 : Multiple Limit Upper Segment 2 Status On/Off
bit 7 : Multiple Limit Upper Segment 2 Beep Level ABOVE/BELOW
296)Status Byte 5
( 0b = Off/Beep if data is below line, 1b = On/Beep if data is above line)
(LSB) bit 0 : Multiple Limit Upper Segment 3 | Status On/Off | |
bit 1 : Multiple Limit Upper Segment 3 Beep Level ABOVE/BELOW | ||
bit 2 : Multiple Limit Upper Segment 4 | Status On/Off | |
bit 3 : Multiple Limit Upper Segment 4 Beep Level ABOVE/BELOW | ||
bit 4 | : Multiple Limit Upper Segment 5 | Status On/Off |
bit 5 | : Multiple Limit Upper Segment 5 Beep Level ABOVE/BELOW | |
bit 6 | : Multiple Limit Lower Segment 1 Status On/Off | |
bit 7 | : Multiple Limit Lower Segment 1 Beep Level ABOVE/BELOW172 |
297) Status Byte 6
(0b = Off/Beep if data is BELOW line, 1b = On/Beep if data is ABOVE line)
(LSB) | bit 0 : Multiple Limit Lower Segment 2 | Status On/Off | |
| bit 1 : Multiple Limit Lower Segment 2 Beep Level ABOVE/BELOW | ||
| bit 2 : Multiple Limit Lower Segment 3 | Status On/Off | |
| bit 3 : Multiple Limit Lower Segment 3 Beep Level ABOVE/BELOW | ||
| bit 4 : Multiple Limit Lower Segment 4 | Status On/Off | |
| bit 5 | : Multiple Limit Lower Segment 4 Beep Level ABOVE/BELOW | |
| bit 6 | : Multiple Limit Lower Segment 5 | Status On/Off |
| bit 7 | : Multiple Limit Lower Segment 5 Beep Level ABOVE/BELOW | |
298) Status Byte 7 |
|
| |
(LSB) | bits | ||
|
|
|
|
170For bits 2, 1 and 0 (“X” is “don’t care): 0X0=no limit, 1X0=single limit, 0X1=multiple limit, 1X1=multiple limit.
171Upper limits always trigger an error beep if data is ABOVE the limit segment, for example, this bit is always 1b.
172LOWER limits always trigger an error beep if data is BELOW the limit segment, for example, this bit is always 0b.
Site Master PM | 55 |