Installationand Maintenance Manual Master Index In-21
Octel 200/300 S.4.1PB60019-01
Remote analogue networking
NameNet for OctelNet, 9−8–9−9
OctelNet, alphabetic (ASCII) name, 9−8–9−9
Remote networking, INSTALL program, 1-13
Remove
AC subassemblies, 9-44, 9-48
air filter, 9-50
digital trunk interface card, 9-21
disk drive backplane, 9-58
fan panel, 9-49
fan tray, 9-50
fax application processor, 9-23
floppy disk drive, 9-27
hard disk drive, 9-25
LAN card, 9-16
line interface card, 9-13
load resistor assembly, 9-60
motherboard assembly, 9-52, 9-54
option control chip, 9-62
power filter assembly, 9-32
Removing Integration Cards, 9-15
Reports, 5-2–5-40
CLEAR command, 6-4
clearing, 5-4
Digital Network Performance Report, 5-14–5-17,
8−68–8−71
digital networking, 8−65–8−71
disk usage, 5-27–5-28
incoming call, call processing, 5-25
integration calling statistics, 5-35–5-36
listing, 5-2
mailbox usage, 5-33
network traffic, 5-17–5-22
Network Traffic Report, digital information,
8−65–8−67
password, 6-14
port statistics, 5-29–5-32
remote analog networking, Network Traffic Report,
2−44
system performance, 5-6–5-16
system performance by COS, 5-37–5-40
user calling statistics, 5-25–5-26
user message statistics, 5-23–5-24
user statistics, 5-3
user status detail, 5-34
System reset, 4−23
Reset , 4−23
Reshipping procedures, 4−2
RESTARTcommand, 6-18
Restore
all messages, 12-23
all names, 12-25
command. See Procedures
greeting to different mailbox, 12-34
language prompts, 12-37
adding, 12-73
local names, 12-27
name to different mailbox, 12-29
network names, 12-31
personal distribution list names, 12-36
scripted or sequential mailbox, 12-35
single greeting, 12-33
Restore procedures, 12-22–12-38
RIC. See ROLM Adaptive Integration;ROLM
Integration Card
ring cycles, QSIG Integration, 17−5
Ring-no-answer, test, 4−31
Ring-through diagnostic test, 6-36
Ringback, 1-25
ROLM 9751 Adaptive Integration, 8.2-1–8.2-35
ROLM 9751 Adaptive Integration
Called Party Identification
direct internal call, 8.2-3
forwarded external calls (RNA or Busy), 8.2-2
forwarded internal calls, 8.2-3
hardware requirements, 8.2-4
installation checklist, 8.2-33–8.2-35
maintenance commands, 8.2-30
Overture 200/300, Called Party Identification,
8.2-14
Overture 200/300 configuration, 8.2-13–8.2-35
Message Waiting Indication, 8.2-13
PBX configuration, customer telephones, 8.2-11
RIC board installation, 8.2-28
software requirements, 8.2-5
testing procedure, 8.2-16–8.2-35
ROLM Adaptive Integration, 8.1-1–8.1-36
Called Party Identification
direct calls from external trunks, 8.1-2, 8.2-2
direct internal call, 8.1-2
forwarded external calls (RNA or Busy), 8.1-2
forwarded internal calls, 8.1-3
hardware requirements, 8.1-4
installation checklist, 8.1-34–8.1-36
maintenance commands, 8.1-31
Overture 200/300 configuration, 8.1-12–8.1-36
Called Party Identification, 8.1-12
Message Waiting Indication, 8.1-12
PBX configuration
customer telephones, 8.1-11
incoming trunks, 8.1-5
port extensions, 8.1-5
RIC display phone extensions, 8.1-5
RIC board installation, 8.1-29
software requirements, 8.1-4
testing procedure, 8.1-15–8.1-36
ROLM Integration Card, 2-8