Appendices

Patch Change

When transmitted: Transmits the patch number.

 

DATA: Patch Number

 

When received: Changes the Patch.

DATA: Patch Number

 

Data size is fixed at 2 bytes.

 

 

 

Upon receiving RQ1, the GS-10 replies with the patch number.

 

Request size to the GS-10 at this time is fixed at 2 bytes (set at 00 00 00 02).

Patch Write

When received: After the patch is written, the patch is switched to the received patch number, and the Current Patch is output.

Current Patch

When received: Current patch number is transmitted (only when RQ1 is received).

Patch

When transmitted: DATA: 01H is transmitted.

 

 

Initialize

When received: Initial value is set if DATA: 01H is received.

 

Data size is fixed at 1 byte.

 

 

AMP Ch Copy

When transmitted: Copy-destination amp channel is transmitted.

 

When received: Copy-destination amp channel is received.

 

Data size is fixed at 1 byte.

 

 

Quick Fx Number

When transmitted: Quick Fx number is transmitted.

DATA: Quick Fx Number

 

When received: Quick Fx number is changed.

 

DATA: Quick Fx Number

 

Data size is fixed at 1 byte.

 

 

Quick Fx Count

Number of Quick Fx in each Effect block.

 

 

 

Request size is fixed at 1 byte (set at 00 00 00 01).

 

 

TUNER/METER

Mode 01H: TUNER Mode

 

 

 

02H: METER Mode

 

 

 

00H: exit (Play Mode)

 

 

 

* In TUNER mode: Pitch, Note data transmitted.

 

 

 

* In METER mode: METER POINT data transmitted.

 

During TAP operations: Delay Time, Delay Time (Fine) transmitted (when setting BPM: Master BPM transmitted).

*The GS-10 can use two methods of communication; Individual Parameter and Bulk Dump.

*Bulk data can be received when the Bulk Load Ready function is accessed in “MIDI:Bulk Load” screen (System mode).

* Although individual data can be received at any time, be sure to appropriately describe the value for one parameter in one packet [F0...F7].

*Do not use an address appended with “#” as the first address.

*Do not specify an odd-number address for Quick Fx Data, SYSTEM:MIDI Program Map.

*Parameters for which Size is 2 or higher should not be separated; make sure these are sent in the same packet.

*Parameters with Size of 2 or higher transmitted from the specified addresses in sequence, from MSB to LSB.

*Output of Quick Fx Name and EFFECT CHAIN is fixed as 12 bytes.

Table TUNER <TUNER>

--------------------------------------------------------------------------------------------------------------

Address(H) Size(H) Data(H) ParameterDescription

--------------------------------------------------------------------------------------------------------------

00 00

00 00

00 00 00

01

00

- 0A

TUNER Pitch

00 : 435Hz

 

 

 

 

 

 

 

01

: 436Hz

 

 

 

 

 

 

 

 

:

 

 

 

 

 

 

 

0A

: 445Hz

00 00

00 01

00 00 00

01

00

- 01

TUNER Out

00

: Mute

 

 

 

 

 

 

 

01

: Bypass

Table OUTPUT <SYSTEM: OUTPUT SELECT>

--------------------------------------------------------------------------------------------------------------

Address(H) Size(H) Data(H) ParameterDescription

--------------------------------------------------------------------------------------------------------------

01 00 00 00

00 00 00 01

00 - 04

OUTPUT Select

00 :

LINE/PHONES

 

 

 

 

01

:

COMBO AMP

 

 

 

 

02

:

STACK AMP

 

 

 

 

03

:

COMBO

Return

 

 

 

 

04

:

STACK

Return

92

Page 92
Image 92
Boss Audio Systems GS-10 owner manual Table Tuner Tuner, Table Output System Output Select