SpecificationValue | Brocade Communications Systems DCX 8510-4

Power specifications

A

NOTE

If any of the following intelligent blades are used, 200-240 VAC is required: FS8-18, FX8-24.

Table 18 shows the basic power specifications for each power supply.

TABLE.18 Power specifications

SpecificationValue

Input voltage	Range: 85-264 VAC Auto-volt, Nominal: 100-240 VAC.

Input frequency	Range: 47-63 Hz; Nominal: 50-60 Hz.

Inrush current	Limited to 60A peak for any initial current surge or spike of 10ms or less at
	either cold or warm start. Any additional inrush current surges or spikes in
	the form of AC cycles or multiple AC cycles greater than 10ms, and less than
	150ms, must not exceed 15A peak.

Power supply output (each)	Low line (85-132 VAC), 1000W; High line (180-264 VAC), 2000W.

The power requirements for a given configuration depend on which blades have been installed in the chassis. Table 19 shows the power draw for the blades that can be used in the Brocade DCX 8510-4 chassis along with the power draw for the cooling fans.

All numbers for the blades assume that the blade is fully populated with optical transceivers, including QSFPs for the core blades. All ports are Fibre Channel except where noted.

You can calculate your power requirements by combining the power draws for the various blades and fan units in your configuration. While you may use fewer ports in a given blade, it is always safer to use the power requirement of a fully populated blade.

TABLE 19 Power demands per component

Blade or fan	Maximum	Type of Blade	Ports per blade	Number of blades	Total ports per chassis
units	Power Draw			permitted in chassis
	(Watts)

CP8	40	Control	NA	2	NA
		blade

CR16-4	135	Core blade	8 64 Gbps QSFP	2	16 quad ports (64
			ports		ports)

FC8-32E	140	Port blade	32 8 Gbps SFP+	up to 4	128
(8Gb)

FC8-48E	160.4	Port blade	48 8 Gbps SFP+	up to 4	192
(8Gb)

FC16-32	140	Port blade	32 16 Gbps SFP+	up to 4	128
(16Gb)			-can use 8 Gbps
			SFP+

FC16-48	160.4	Port blade	48 16 Gbps SFP+	up to 4	192
(16Gb)			-can use 8 Gbps
			SFP+

FC8-64 (8Gb)	126.4	Port blade	64 8Gbps SFP+	up to 4	256

FS8-18	235	Encryption	16 8 Gbps SFP+	up to 4	64
		blade

Brocade DCX 8510-4 Backbone Hardware Reference Manual	115
53-1002177-05

Image 135

Brocade Communications Systems DCX 8510-4 manual SpecificationValue, Blade or fan Maximum, Ports per blade Number of blades

Contents

Brocade DCX 8510-4 Backbone Brocade Communications Systems, Incorporated Brocade DCX 8510-4 Backbone Hardware Reference Manual Brocade DCX 8510-4 Backbone Hardware Reference Manual Contents This chapter Monitoring overview Chapter Logging In and Configuring the Brocade DCX Chapter Removal and Replacement Procedures Appendix a Specifications FS8-18 blade FX8-24 blade DiagnosticsTroubleshooting This appendix Brocade DCX 8510-4 Backbone Hardware Reference Manual Figures Page Tables Page How this document is organized This chapter Text formatting Supported hardware and softwareWhat’s new in this document Document conventions Show WWN Command syntax conventionsCommand examples Command Option, option Argument, arg Additional information Brocade resourcesCorporation Referenced Trademarks and Products Other industry resources Getting technical help Documentation@brocade.com Document feedback Brocade DCX 8510-4 Backbone Overview Brocade DCX 8510-4 features Brocade DCX 8510-4 hardware components Page Port side of the Brocade DCX Port side of the Brocade DCX 8510-4 sample configuration Brocade DCX 8510-4 hardware components Nonport side of the Brocade DCX Description Name Function Brocade DCX 8510-4 blades Reliability High availability Software features Serviceability Security SSHv2 using AES, 3DES, RSA Https using AES SNPMv3 Network manageability Network manageability Time and items required Installation of the Brocade DCX Installation task Time estimate Items required Preparing for Brocade DCX 8510-4 installationPage Unpacking and installing the Brocade DCX Unpacking and installing the Brocade DCXUse safe lifting practices when moving the product. C015 Items included with the Brocade DCX Items included with the Brocade DCX Providing power to the Brocade DCX Providing power to the Brocade DCXPort numbering Cable management Chassis slots High density cabling Installing inter-chassis link Qsfp cables optional Cable management Configuring the Brocade DCX Logging In and Configuring the Brocade DCX Establishing a serial connection to the Brocade DCX Illustrates the flow of the basic configuration tasks Logging in to the serial console port Proceed to the next taskParameter Value Configuring the IP addresses Establishing an Ethernet connection to the Brocade DCX SwDiradmin ipaddrset -chassis Ethernet IP Address 0.0.0.0 Customizing a switch name Customizing a chassis nameRecord the new name for reference Enter configure Setting the domain IDSetting the date and time Setting the date You are prompted to select a general location Setting the time zone Verifying the PID mode Verifying the PID modeSynchronizing local time Determining installed software licenses Installing transceivers and attaching cablesInstalling SFP+ and mSFP transceivers and cables Installing Qsfp transceivers and cables OFF Managing cables Managing cables ConfigShow IpaddrShow LicenseShow SwitchShow Powering off the Brocade DCX Powering off the Brocade DCX Powering off the Brocade DCX Monitoring overview Monitoring System Components 820000 Online SW Blade AP Blade AGC2M03FR7T Illustrates the FC8-64 port blade Blade illustrations FC8-32E port blade FC16-32 port blade FS8-18 encryption blade Color Status Recommended action LED purpose Color Status Recommended action PortCfgPersistentEnable Determining the status of a control processor blade CP8 Determining the status of a control processor blade CP8 Determining the status of a core switch blade CR16-4 Determining the status of a core switch blade CR16-4 Qsfp Determining the status of a power supply Determining the status of a blower assembly Determining the status of a blower assembly Determining the status of a WWN card Determining the status of a WWN card WWN unit fails to power on Type of message Sample error message WWN bezel logo plate for DCX Determining the status of a WWN card Introduction ESD precautions Removing a chassis door Chassis door removal and replacementChassis door removal and replacement Time and items required Vertical cable management fingers removal and replacement Removing a cable management finger assemblyVertical cable management fingers removal and replacement Replacing a cable management finger assembly Removing a blade Replacing a blade Blade filler panel removal and replacement Blade filler panel removal and replacementRemoving a filler panel Control processor blade CP8 removal and replacement Control processor blade CP8 removal and replacementReplacing a filler panel Faulty CP blade indicators Recording critical Brocade DCX 8510-4 information Removing a control processor blade CP8 Replacing a control processor blade CP8 Verifying operation of the new CP blade Downloading firmware from an FTP server Downloading firmware from a USB device Brocade DCX 8510-4 Backbone Hardware Reference Manual Completing the replacement Faulty core switch blade indicators Core switch blade CR16-4 removal and replacement Removing a core switch blade CR16-4 Power supply removal and replacement Replacing a core switch blade CR16-4Power supply removal and replacement Removing a power supply Identifying power supplies Blower assembly removal and replacement Replacing a power supplyUse this procedure to remove and replace a blower assembly Removing a blower assembly Replacing a blower assembly WWN card removal and replacement Verifying the need for replacement Preparing for the WWN card replacementRemoving the WWN bezel logo plate and WWN card Brocade DCX 8510-4 Backbone Hardware Reference Manual Replacing the WWN card and WWN bezel logo plate Transceiver removal and replacement Removing an SFP+ transceiver Removing and replacing an mSFP optical transceiver Replacing an SFP+ transceiver Use this procedure to remove and replace a Qsfp cable Inter-chassis link Qsfp cable removal and replacement Qsfp cable insertion Removing an ICL cable Replacing an ICL cableComplete the following steps to replace a Qsfp cable Possible ICL configurations Chassis 1 DCX Chassis 2 DCX DCX 8510 core/edge ICL topology DCX 8510 full mesh ICL topology Brocade DCX 8510-4 chassis removal and replacement Faulty Brocade DCX 8510-4 chassis indicators Recording critical Brocade DCX 8510-4 and SAN information Critical information checklist Switch NsShow NsAllShow SwitchShow -qsfp FabricShow Sysshutdown Disconnecting from the network and fabric Removing components from the chassis Installing the replacement chassis Installing components into the new chassis Switchadmin configdownload -all Downloading the configuration Verifying correct operation of the system Reconnecting the system to the network and fabric Verifying correct configuration of the fabric NsShow NsAllShow SwitchShow FabricShowLscfg --showif using the Virtual Fabric feature Cable routing table for Brocade DCX 8510-4 64 ports shown Cable routing table Slot/port Slot Port Switch end Device endPage General specifications This appendixDescription System architecture General specifications FeatureDescriptionSystem architecture System size and weight System size and weight System architectureFeature Description Weight System blade and FRU weightsSystem blade and FRU weights System size and weight System Size or weight Condition Acceptable range during operation Facility requirements System FRU weightsFacility requirements Environmental requirements Power specifications Fibre Channel port specifications Ports per blade Number of blades SpecificationValueUnits Power Draw Blade or fan Maximum VAC nominal Power cordsPower cords Power demands per component Demand All locations Power cords Power cord types international Power cords Power cord types international Power cord notice Power cord notice Japan DenanData transmission ranges Type Microns OM1 OM2 OM3 OM4 Qualified cables for the FC8-64 port bladeForm factor Speed Multimode media Regulatory compliance Safety notices Bsmi statement Taiwan FCC warning US onlyKCC statement Republic of Korea Vcci statement Japan Laser compliance CE statementCanadian requirements German statement Country Standards SafetyEnvironmental regulation compliance China RoHS Environmental Protection Use Period Epup Disclaimer Environmental regulation compliance Environmental regulation compliance Environmental regulation compliance FS8-18 blade Application and Encryption Blades Fcip FX8-24 bladePage FX8-24 blade Diagnostics and Troubleshooting Interpreting Post and boot results Command Information displayedObtaining chassis and component status Boot Diagnostics Troubleshooting Troubleshooting the Brocade DCXIssue Possible cause Recommended action See the Fabric OS Administrator’s Guide for Troubleshooting Troubleshooting the Brocade DCX Source of the problem or replace the blade as Port Numbering Template Port Numbering Template FC16-48 port blade GbE ports FC ports Blade Power LED Blade Status LED Index 144 145 RRP 147