Time and items required | Brocade Communications Systems DCX 8510-4

5 Chassis door removal and replacement

Chassis door removal and replacement

NOTE

The chassis door must be installed to ensure the Brocade DCX 8510-4 meets EMI and other regulatory certifications. Additionally, if ICL cables are not used, EMI plugs must be inserted in the ICL cable ports to meet certification standards.

Time and items required

The replacement procedure for the chassis door takes less than five minutes. See Figure 18.

Removing a chassis door

Support the door to prevent it from falling. Pull and remove the door. It will pop off the ball studs.

FIGURE 18 Removal and replacement of the chassis door

Replacing a chassis door

Complete the following steps to reinstall the door.

1.Align the holes in the door with the ball studs on the chassis

2.Push the door into place. It will snap onto the studs.

60	Brocade DCX 8510-4 Backbone Hardware Reference Manual
	53-1002177-05

Image 80

Brocade Communications Systems DCX 8510-4 manual Chassis door removal and replacement, Time and items required

Contents

Brocade DCX 8510-4 Backbone Brocade Communications Systems, Incorporated Brocade DCX 8510-4 Backbone Hardware Reference Manual Brocade DCX 8510-4 Backbone Hardware Reference Manual Contents Chapter Logging In and Configuring the Brocade DCX This chapter Monitoring overview Chapter Removal and Replacement Procedures Appendix a Specifications Diagnostics TroubleshootingThis appendix FS8-18 blade FX8-24 blade Brocade DCX 8510-4 Backbone Hardware Reference Manual Figures Page Tables Page This chapter How this document is organized Supported hardware and software What’s new in this documentDocument conventions Text formatting Command syntax conventions Command examplesCommand Option, option Argument, arg Show WWN Corporation Referenced Trademarks and Products Additional informationBrocade resources Getting technical help Other industry resources Document feedback Documentation@brocade.com Brocade DCX 8510-4 features Brocade DCX 8510-4 Backbone Overview Brocade DCX 8510-4 hardware components Page Port side of the Brocade DCX 8510-4 sample configuration Port side of the Brocade DCX Brocade DCX 8510-4 hardware components Nonport side of the Brocade DCX Brocade DCX 8510-4 blades Description Name Function High availability Reliability Serviceability Software features SSHv2 using AES, 3DES, RSA Https using AES SNPMv3 Security Network manageability Network manageability Installation of the Brocade DCX Time and items required Preparing for Brocade DCX 8510-4 installation Installation task Time estimate Items requiredPage Use safe lifting practices when moving the product. C015 Unpacking and installing the Brocade DCXUnpacking and installing the Brocade DCX Items included with the Brocade DCX Items included with the Brocade DCX Port numbering Providing power to the Brocade DCXProviding power to the Brocade DCX Chassis slots Cable management High density cabling Installing inter-chassis link Qsfp cables optional Cable management Logging In and Configuring the Brocade DCX Configuring the Brocade DCX Illustrates the flow of the basic configuration tasks Establishing a serial connection to the Brocade DCX Parameter Value Logging in to the serial console portProceed to the next task Configuring the IP addresses SwDiradmin ipaddrset -chassis Ethernet IP Address 0.0.0.0 Establishing an Ethernet connection to the Brocade DCX Record the new name for reference Customizing a switch nameCustomizing a chassis name Setting the domain ID Setting the date and timeSetting the date Enter configure Setting the time zone You are prompted to select a general location Synchronizing local time Verifying the PID modeVerifying the PID mode Installing SFP+ and mSFP transceivers and cables Determining installed software licensesInstalling transceivers and attaching cables Installing Qsfp transceivers and cables OFF Managing cables Managing cables Powering off the Brocade DCX ConfigShow IpaddrShow LicenseShow SwitchShow Powering off the Brocade DCX Powering off the Brocade DCX Monitoring System Components Monitoring overview 820000 Online SW Blade AP Blade AGC2M03FR7T Blade illustrations Illustrates the FC8-64 port blade FC8-32E port blade FC16-32 port blade FS8-18 encryption blade Color Status Recommended action PortCfgPersistentEnable LED purpose Color Status Recommended action Determining the status of a control processor blade CP8 Determining the status of a control processor blade CP8 Determining the status of a core switch blade CR16-4 Determining the status of a core switch blade CR16-4 Determining the status of a power supply Qsfp Determining the status of a blower assembly Determining the status of a blower assembly Determining the status of a WWN card Determining the status of a WWN card Type of message Sample error message WWN unit fails to power on WWN bezel logo plate for DCX Determining the status of a WWN card ESD precautions Introduction Chassis door removal and replacement Chassis door removal and replacementTime and items required Removing a chassis door Vertical cable management fingers removal and replacement Vertical cable management fingers removal and replacementRemoving a cable management finger assembly Replacing a cable management finger assembly Removing a blade Replacing a blade Removing a filler panel Blade filler panel removal and replacementBlade filler panel removal and replacement Replacing a filler panel Control processor blade CP8 removal and replacementControl processor blade CP8 removal and replacement Faulty CP blade indicators Recording critical Brocade DCX 8510-4 information Removing a control processor blade CP8 Replacing a control processor blade CP8 Verifying operation of the new CP blade Downloading firmware from an FTP server Downloading firmware from a USB device Brocade DCX 8510-4 Backbone Hardware Reference Manual Completing the replacement Core switch blade CR16-4 removal and replacement Faulty core switch blade indicators Removing a core switch blade CR16-4 Power supply removal and replacement Power supply removal and replacementReplacing a core switch blade CR16-4 Identifying power supplies Removing a power supply Use this procedure to remove and replace a blower assembly Blower assembly removal and replacementReplacing a power supply Removing a blower assembly WWN card removal and replacement Replacing a blower assembly Removing the WWN bezel logo plate and WWN card Verifying the need for replacementPreparing for the WWN card replacement Brocade DCX 8510-4 Backbone Hardware Reference Manual Transceiver removal and replacement Replacing the WWN card and WWN bezel logo plate Removing an SFP+ transceiver Replacing an SFP+ transceiver Removing and replacing an mSFP optical transceiver Inter-chassis link Qsfp cable removal and replacement Use this procedure to remove and replace a Qsfp cable Qsfp cable insertion Complete the following steps to replace a Qsfp cable Removing an ICL cableReplacing an ICL cable Possible ICL configurations Chassis 1 DCX Chassis 2 DCX DCX 8510 core/edge ICL topology Brocade DCX 8510-4 chassis removal and replacement DCX 8510 full mesh ICL topology Faulty Brocade DCX 8510-4 chassis indicators Critical information checklist Recording critical Brocade DCX 8510-4 and SAN information Switch NsShow NsAllShow SwitchShow -qsfp FabricShow Disconnecting from the network and fabric Sysshutdown Installing the replacement chassis Removing components from the chassis Installing components into the new chassis Downloading the configuration Switchadmin configdownload -all Verifying correct operation of the system Reconnecting the system to the network and fabric Lscfg --showif using the Virtual Fabric feature Verifying correct configuration of the fabricNsShow NsAllShow SwitchShow FabricShow Cable routing table Cable routing table for Brocade DCX 8510-4 64 ports shown Slot Port Switch end Device end Slot/portPage Description General specificationsThis appendix System architecture System architecture General specificationsFeatureDescription Feature Description System size and weightSystem size and weight System architecture System blade and FRU weights System blade and FRU weights System size and weightSystem Size or weight Weight Facility requirements System FRU weights Facility requirementsEnvironmental requirements Condition Acceptable range during operation Fibre Channel port specifications Power specifications SpecificationValue Units Power DrawBlade or fan Maximum Ports per blade Number of blades Power cords Power cords Power demands per componentDemand VAC nominal Power cords Power cord types international All locations Power cords Power cord types international Data transmission ranges Power cord noticePower cord notice Japan Denan Qualified cables for the FC8-64 port blade Form factor SpeedMultimode media Type Microns OM1 OM2 OM3 OM4 Safety notices Regulatory compliance FCC warning US only KCC statement Republic of KoreaVcci statement Japan Bsmi statement Taiwan CE statement Canadian requirementsGerman statement Laser compliance Safety Environmental regulation complianceChina RoHS Country Standards Environmental Protection Use Period Epup Disclaimer Environmental regulation compliance Environmental regulation compliance Environmental regulation compliance Application and Encryption Blades FS8-18 blade FX8-24 blade FcipPage FX8-24 blade Diagnostics and Troubleshooting Obtaining chassis and component status Interpreting Post and boot resultsCommand Information displayed Diagnostics Boot Issue Possible cause Recommended action TroubleshootingTroubleshooting the Brocade DCX Troubleshooting Troubleshooting the Brocade DCX See the Fabric OS Administrator’s Guide for Source of the problem or replace the blade as Port Numbering Template Port Numbering Template FC16-48 port blade GbE ports FC ports Blade Power LED Blade Status LED Index 144 145 RRP 147