Network Address Translation

NAT: tcp data src 10.10.100.18:1144 => trans 192.168.2.78:8012 dst 192.168.3.11:53

NAT: 192.168.2.78:8012 192.168.3.11:53 flags A ID 65302 len 40 txfid 13

NAT: tcp data src 10.10.100.18:1144 => trans 192.168.2.78:8012 dst 192.168.3.11:53

NAT: 192.168.2.78:8012 192.168.3.11:53 flags FA ID 23 len 40 txfid 13

NAT: tcp data dest 192.168.2.78:8012 => trans 192.168.3.11:53 dst 10.10.100.18:1144

NAT: 192.168.3.11:53 10.10.100.18:1144 flags A ID 64923 len 40 txfid 15

NAT: tcp data dest 192.168.2.78:8012 => trans 192.168.3.11:53 dst 10.10.100.18:1144

NAT: 192.168.3.11:53 10.10.100.18:1144 flags FA ID 64924 len 40 txfid 15

NAT: tcp data src 10.10.100.18:1144 => trans 192.168.2.78:8012 dst 192.168.3.11:53

NAT: 192.168.2.78:8012 192.168.3.11:53 flags A ID 279 len 40 txfid 13

HP9300# debug ip nat udp 192.168.3.11

NAT: udp src 10.10.100.18:1140 => trans 192.168.2.78:8008 dst 192.168.3.11:53

NAT: udp data src 10.10.100.18:1140 => trans 192.168.2.78:8008 dst 192.168.3.11:53

NAT: 192.168.2.78:8008 192.168.3.11:53 ID 54806 len 63 txfid 13

NAT: udp src 10.10.100.18:1141 => trans 192.168.2.78:8009 dst 192.168.3.11:53

NAT: udp data src 10.10.100.18:1141 => trans 192.168.2.78:8009 dst 192.168.3.11:53

NAT: 192.168.2.78:8009 192.168.3.11:53 ID 55062 len 63 txfid 13

NAT: udp data dest 192.168.2.78:8008 => trans 192.168.3.11:53 dst 10.10.100.18:1140

NAT: 192.168.3.11:53 10.10.100.18:1140 ID 56965 len 246 txfid 15

NAT: udp data dest 192.168.2.78:8009 => trans 192.168.3.11:53 dst 10.10.100.18:1141

NAT: 192.168.3.11:53 10.10.100.18:1141 ID 56966 len 246 txfid 15

HP9300# debug ip nat transdata

NAT: icmp src 10.10.100.18:2048 => trans 192.168.2.79 dst 204.71.202.127

NAT: udp src 10.10.100.18:1561 => trans 192.168.2.79:65286 dst 192.168.3.11:53

NAT: tcp src 10.10.100.18:1473 => trans 192.168.2.78:8016 dst 192.168.2.158:53

To disable the NAT diagnostic mode, enter a command such as the following:

HP9300# no debug ip nat tcp

This command disables the diagnostic mode for NAT performed on TCP packets. NAT diagnostics for other types of packets remain enabled.

You also can use the following syntax to disable the diagnostic mode for NAT:

Syntax: undebug ip nat icmp tcp udp transdata

11 - 13