Manuals / HP / Computer Equipment / Software

HP nPartitions (nPars) manual Accessing Uefi or the OS from iLO 3 MP

Models: nPartitions (nPars)

1 148

Download 148 pages 8.77 Kb

Page 27

To configure specific devices, press D or d to launch the Device Manager. This is an advanced feature and should only be performed when directed.

To perform maintenance on the system such as adding, deleting, or reordering boot options, press M or m to launch the Boot Maintenance Manager.

Accessing UEFI or the OS from iLO 3 MP 27

Image 27

HP nPartitions (nPars) manual Accessing Uefi or the OS from iLO 3 MP

Contents

Abstract HP-UX Contents Optional components TroubleshootingSupport and other resources 119 Removing and replacing componentsIndex 146 Regulatory information 145Server blade overview OverviewCPU0 Server blade componentsSite preparation Server blade dimensions and weightServer blade dimensions and weight for the BL860c Blade Link dimensions and weightCustomer and HP Information Site Inspection ChecklistSample Site Inspection Checklist Power subsystem ESD handling informationUnpacking and inspecting the server blade Verifying the inventory Verifying site preparationInspect the shipping containers for damage Unpacking the server bladePreparing the enclosure Installing the server blade into the enclosureInstallation sequence and checklist Installing and powering on the server bladeRemoving a c7000 device bay divider Slide the locking tab down Installing interconnect modules Interconnect bay numbering and device mapping Installing the server blade into the enclosure Power States Server blade power statesPowering off the server blade Powering on the server bladeBL1 Blade Link bay location rulesBL2E Installing the server blade into the enclosure Accessing Uefi or the OS from iLO 3 MP Using iLOUefi Front Accessing Uefi or the OS from iLO 3 MP Operating system is loaded onto the server blade Booting and installing the operating systemOS login prompt Saving Uefi configuration settingsInstalling the latest firmware using HP Smart Update Manager Operating system procedures Installing the operating system onto the server bladeOperating systems supported on the server blade Installing the OS using HP Ignite-UX Installing the OS using vMediaContinue with Configuring system boot options Configuring system boot options Booting and shutting down HP-UXAdding HP-UX to the boot options list Booting HP-UX from the Uefi Boot Manager HP-UX standard bootShutting down HP-UX Booting HP-UX in single-user modeBooting HP-UX in LVM-maintenance mode Booting HP-UX from the Uefi ShellBooting and shutting down HP-UX Partner blades Optional componentsHot-plug SAS disk drives Removing the access panel Installing internal componentsProcessor load order Processor and heatsink moduleOptional components Installing internal components Optional components Installing internal components DIMMs Dimm installation guidelinesDimm pair load order PerformanceMixed Dimm load order Dimm pair load order Mixed Dimm load order Dimm quad load order Dimm quad load order rulesInstalling Dimms Mezzanine cards Remove the access panel Removing the access panelHP Smart Array P711m Controller Supercap pack mounting kit Installing the Supercap mounting bracketSlot Installing the P711m controller boardInstalling the Supercap Pack Replacing the access panel Upgrading a conjoined configurationProcedure summary Before getting started Upgrade kit contentsSupported operating systems Minimum firmware versionsDetermining your current firmware revisions Sysrev Uuid VCM Rules for server blade internal components Existing server blade check Upgrading the original serverAdding resources Installing internal components Ilo002264fed1da CMhpiLO- sr Sysset Command successful Installing internal components Final hardware check Booting the operating system Warranty registrationSupport Operating System Licenses Blade link and system information parametersQuick Boot option FC SAN connections FCoE SAN connections Ethernet network connections Profile entry Assigned network Post-Upgrade Procedure for PI Pre-Upgrade Procedure for PIGioportableimage before Immed Now Troubleshooting General troubleshooting methodologyMethodology Methodology Troubleshooting Entry Points Executing recommended troubleshooting methodologyBasic Low End Troubleshooting Basic and advanced troubleshooting tablesCannot find a boot disk. The iLO 3 MP is running Properly installed and fully seated Advanced Low End TroubleshootingSl -e -nc Df -d Sysset Npar Uefi info all Troubleshooting toolsRear panel view Controls and portsServer blade LEDs Front panel viewUID LED Front panel LEDsSAS hard drive LED combinations SAS disk drive LEDsDrive might terminate the current Virtual Front Panel LEDs in the iLO 3 TUI Blade Link LEDsIndications for the iLO 3 TUI LEDs Health LED SUV Cable and Ports Connecting to the serial portHP-UX Fault management DiagnosticsGeneral diagnostic tools Fault management overviewErrors and error logs Event log definitionsEvent log usage ILO 3 MP event logs SEL review Firmware Troubleshooting processorsEnclosure information Cooling subsystemVerify and install the latest firmware Troubleshooting the server interface system consoleTroubleshooting the environment Identifying and troubleshooting firmware issuesServer blade environmental specifications Removing and replacing components Server blade components listCRU List 512744-001 AD399-2134A Powering off the server blade Blade Link for BL870c i4 or BL890c i4 configurationsPreparing the server blade for servicing Preparing the server blade for servicing Blade Link for BL860c i4 configurations Preparing the server blade for servicing Access panel Power off the server blade. Powering off the server bladeServer blade Disk drive blanks Disk drivesRemoving a disk drive blank Dimm baffle DIMMs CPU baffle CPU and heatsink module Removing and replacing components CPU and heatsink module SAS backplane Server batteryMezzanine cards System board ICH mezzanine boardProcessor and heatsink module CPU and heatsink module Blade LinkUse the indent to pull the door open Contacting HP Support and other resourcesNew and changed information in this edition Typographic conventionsHP Insight Remote Support Software Understood or followed will result in personal injury or Asic Standard terms, abbreviations, and acronymsLdap TUI Syntax RAID configuration and other utilitiesConfiguring a Smart Array Controller Using the saupdate commandSetmode Determining the Driver ID and Ctrl ID Updating the firmware using saupdateRAID configuration and other utilities Creating a logical drive Deleting a logical drive Drivers Useful Uefi command checksUefi Shell Commands Uefi Shell and HP Posse commandsControls batch file command echoing or displays a message Displays or modifies MEM/MMIO/IO/PCI/PCIE address space Drive paths in Uefi Using the Boot Maintenance ManagerAdd Boot Option Boot OptionsDelete Boot Option Change Boot Order Add Driver Option Driver OptionsConsole Configuration Delete Driver OptionChange Driver Order Using the Boot Maintenance Manager Set Boot Next Value Boot From FileSet Time Out Value Reset SystemILO 3 MP Regulatory information Turkey RoHS material content declarationUkraine RoHS material content declaration Warranty informationDrvcfg Index147 Turkey RoHS material content declaration