COAX

SETUP

VALUE

 

 

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

MENU

ITEM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EDGE-EDGE

OFF*

Turns

edge-to-edge

 

printing

on

or

off.

 

 

 

 

 

 

 

 

 

 

 

ON

Ÿ OFF—the

printer

maintains

a

border

of

4

mm

on

all

four

 

 

 

 

 

 

paper sides.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ÿ ON—The printer allows printing

up

to

the

physical

page

size.

 

 

 

Notes:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. To prevent toner from contaminating the printer, IBM

 

 

 

 

recommends leaving EDGE-EDGE

set

to

OFF;

use

ON

only

 

 

 

 

 

when

necessary.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2. The Coax Setup Menu item

EDGE-EDGE applies to SCS

 

 

 

 

 

 

data

only. To

specify

 

edge-to-edge printing

for

IPDS

data,

 

 

 

use the EDGE-EDGE

item

on

the

IPDS

Menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EAB

 

DISABLE*

Enables

or

disables

the

extended

attribute

buffer.

 

 

 

ENABLE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BUFFERSIZE

960

Specifies

the

buffer

size

in

bytes.

 

 

 

 

 

 

 

 

 

 

1920*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2560

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3440

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3564

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EARLY

COMPL

ON*

Turns

early

print completion on or off for non-IPDS data sent over

 

 

OFF

the

coax

attachment. To

turn

early

print

completion

on or

off for

 

 

 

IPDS

data,

use

the EARLY

COMPL item

on

the

IPDS

Menu.

 

 

 

 

Ÿ ON—sends

an

“order

complete”

as

soon

as

data

is

received.

ŸOFF—waits until the print job is physically complete to send “order complete.”

PA1

none

Selecting

this

value

and

pressingContinue/Enterthe

key

sends

 

 

a

PA1

signal

to

the

host.

 

 

 

 

 

 

Note:

This

applies

to

SCS

only;

not

DSC/DSE

or

IPDS.

 

 

 

 

 

 

 

 

 

PA2

none

Selecting

this

value

and

pressingContinue/Enterthe

key

sends

 

 

a

PA2

signal

to

the

host.

 

 

 

 

 

 

Note:

This

applies

to

SCS

only;

not

DSC/DSE

or

IPDS.

Chapter 5. Operator Panel Menus99

Page 119
Image 119
IBM S544-5343-03 manual Setup Value