IPDS

MENU

VALUE

 

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

 

 

 

ITEM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EDGE-EDGE

OFF*

Turns

edge-to-edge

printing

on

or off.

 

 

 

 

 

 

 

 

 

 

ON

Ÿ

OFF—the

printer maintains a no-print border of 4

mm

on

all

four

 

 

 

 

 

 

 

paper

sides.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ÿ

ON—The

printer

allows

printing

up

to

the

physical

page size.

 

 

 

Notes:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. To prevent toner from contaminating

the

printer,

IBM

 

 

recommends

 

 

 

 

leaving

EDGE-EDGE

set

to

OFF;

 

use

ON

only

when

necessary.

 

 

 

 

2.

The IPDS Menu item EDGE-EDGE applies

to IPDS data only. To

 

 

 

 

 

specify edge-to-edge printing for non-IPDS data sent over the coax

 

 

 

 

attachment, use the EDGE-EDGE item on

the Coax Setup Menu. To

 

 

 

 

specify edge-to-edge printing for non-IPDS data sent over the twinax

 

 

 

 

attachment, use the

EDGE-EDGE

item on

the

Twinax

Setup

Menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FONT

SUB

OFF*

Turns

font

substitution

on

or

off.

 

 

 

 

 

 

 

 

 

 

 

ON

Ÿ

OFF—if

a job requests

a

font

that

is

not

loaded

on

the

printer, the port

 

 

 

generates an IPDS NACK message and the host holds the job.

ŸON—if a job requests a font that is not loaded on the printer, the printer attempts to substitute another font.

IPDS

PORT

COAX*

Specifies

 

the

attachment

you

use

for

IPDS

jobs.

 

 

 

 

 

 

 

 

 

TX

Note:

You

 

can

print

IPDS

 

from

more

 

than

one

 

port;

setting

this

item,

 

 

 

TRING

 

 

 

 

 

 

 

therefore,

does

not

restrict

you

from

printing

from

multiple ports. Also,

this

 

 

ETHER

 

 

item

may

not appear on

 

some printers.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EARLY

COMPL

OFF*

Turns

early

print

completion

on

or

off for

IPDS

jobs.

 

 

 

 

 

 

 

 

ON

Ÿ OFF—the printer waits until

the

job

is

physically

complete

to

signal

the

 

 

 

 

 

 

host

that

the

job

is

complete.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ÿ ON—the

 

printer

signals

the

host

that

the

job

 

is

complete

as

soon as

 

 

 

the IPDS data is formatted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Setting EARLY COMPL=ON may improve

print

performance,

 

but

may

also

 

 

 

 

 

 

degrade

 

recovery

and

cause

lost

data

for

some

printing

problems, such

as

 

 

 

jams.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

108 Network Printer 17: User’s Guide

Page 128
Image 128
IBM S544-5343-03 manual Coax, Tring, Ether