|
|
|
| Diagnostics and Troubleshooting | |
|
|
|
|
|
|
| Error | Error Message | Possible Cause | Possible Solution |
|
| Code |
| |||
|
|
|
|
| |
|
|
|
|
|
|
| 15 | timers busy | A low level motor move command | Wait for the motor move to complete |
|
|
|
| was issued while the timer motor | or stop the motor and reissue the |
|
|
|
| was in use. | command. |
|
|
|
|
|
|
|
| 16 | timer spurious interrupt | A spurious (false) timer interrupt | No solution required. |
|
|
| code | has occurred. |
|
|
|
|
|
|
|
|
| 17 | command not | The function requested is not | No solution required. |
|
|
| implemented | supported in this software release. |
|
|
|
|
|
|
|
|
| 18 | unexpected OCP reply | The 300 board sent an unexpected | Call for service. |
|
|
|
| message to the 200 board. |
|
|
|
|
|
|
|
|
| 20 | pec service mode | The service switch for the 200 | Call for service. |
|
|
|
| board is on, enabling |
|
|
|
|
| LEDs that can cause fogging. |
|
|
|
|
|
|
|
|
| 21 | opc service mode | The service switch for the 300 | Call for service. |
|
|
|
| board is on, enabling |
|
|
|
|
| LEDs that can cause fogging. |
|
|
|
|
|
|
|
|
| 22 | end of roll, remove | The paper cassette is empty and | Pull the paper tail out of the sheet |
|
|
| paper at sht xprt | tail of the paper has been fed into | transport area near the knife. |
|
|
|
| the sheet transport area. |
|
|
|
|
|
|
|
|
| 23 | in error state | A previous error has not been | Reinitialize the printer. |
|
|
|
| cleared. |
|
|
|
|
|
|
|
|
| 24 | middle of load | Attempting to perform a function | Wait until paper loading is complete |
|
|
|
| while paper is being loaded. | and perform the function again. |
|
|
|
|
|
|
|
| 25 | wait proc | Attempting to perform a function | Turn on the processor. Wait for the |
|
|
|
| while the printer detects a problem | processor to warm up and then |
|
|
|
| with the processor. | reinitialize the printer. |
|
|
|
|
|
|
|
| 26 | xport back door open | The back sheet transport door was | Close the back sheet transport door. |
|
|
|
| left open. |
|
|
|
|
|
|
|
|
| 27 | xport front door open | The front sheet transport door was | Close the front sheet transport door. |
|
|
|
| left open. |
|
|
|
|
|
|
|
|
| 28 | unit does not fit | The sum of all the unit setups since | Begin printing. |
|
|
|
| the last print start exceeds 33 |
|
|
|
|
| inches. |
|
|
|
|
|
|
|
|
| 29 | sheet fogged in sheet | A door was opened while sending a | Reprint. |
|
|
| xport | sheet from the printer to the |
|
|
|
|
| processor. |
|
|
|
|
|
|
|
|
| 30 | unexpected knife | Knife not detected at either end. | Call for service. |
|
|
| neither limit |
|
|
|
|
|
|
|
|
|
| 31 | door opened briefly | The door was opened and closed. | Reinitialize the printer. |
|
|
|
|
|
|
|
| 64 | bad msg checksum | A problem with a prom has | Call for service. |
|
|
|
| occurred. |
|
|
|
|
|
|
|
|
September 2000 |
