Mitsubishi Electronics FR-V500 DA1 terminal function, Speed monitoring, Reference, Remote setting

Function list (Extended function parameters)

						At-a-glance Guide to Func-
							tions
						": Usable function
Function	Parameter				Cus-	×: Unusable function
						* : Functions that can be used
		Name	Outline	Factory	tomer
						for param eter-set position con-
				Setting	Set-
							trol
					ting
						Vector Control
						Speed	Torque	Position
						control	control	control
			You can select the monitor output DA1 data.
			1: Speed
			2: Output current
			3: Output voltage
			5: Preset speed
			6: Output frequency
			7: Motor torque
			8: Converter output voltage
	54	DA1 terminal function	9: Regenerative brake duty	1		"	"	"
functions		selection	10: Electronic thermal relay load factor
			11: Output current peak value
			18: Motor exciting current
			12: Converter output voltage peak value
Display			17: Load meter
			21: Reference output
			32: Torque command
			33: Torque current command
			34: Motor output
			36: Torque monitor (driving/regenerative polarity switching)
	55	Speed monitoring	You can set the reference value of speed monitoring.	1500r/m in		"	"	"
		reference	0 to 3600r/min
		Current monitoring		Rated
	56		You can set the reference value of current monitoring.	inverter		"	"	"
		reference	0 to 500A	output
				current
restart	57	Restart coasting time	When power is restored after an instantaneous power failure, you can start the inverter	9999		"	"	×
			without stopping the motor (in a coasting status). When this time (Pr. 57) elapses after
			power was restored, the inverter begins to restart.
Automatic			When you set "9999", the inverter will not restart. Generally, you may set "0", but you
	58	Restart cushion time	can adjust the time (0, 0.1 to 5s, 9999) according to the load magnitude.	1.0s		×	×	×
			When the restart coasting time (Pr. 57) elapses, the output voltage is risen gradually.
			Set this cushion time (Pr. 58) (0 to 60s).
			Normally, you can perform operation with the factory settings, but you can adjust them
			according to the load magnitude. Pr. 58 is valid only during V/F control.
function			0: None
			You can make remote setting of the speed when the operation panel is located away
			from the control box.
dditional	59	Remote setting	1: With remote setting function, with frequency setting storage function	0		"	"	×
		function selection	2: With remote setting function, without frequency setting storage function
			3: With remote setting function, without frequency setting storage function
A			(Turning STF/STR off clears remote setting)
			Set when using the brake sequence control.
		Intelligent mode	0: Normal operation mode
	60		7: Brake sequence mode	0		"	×	×
		selection	(With mechanical brake opening completion signal input)
			8: Brake sequence mode
			(Without mechanical brake opening completion signal input)
			You can select alarms for a retry to be made when the protective function is activated.
functions			0:E.OC1 to 3, E.OV1 to 3, E.THM, E.THT, E.IPF, E.UVT, E.BF, E.GF, E.OHT, E.OLT,
			E.OPT, E.OP1 to 3, E.PE, E.OS, E.OSD, E.OD, E.MB1 to 7
	65	Retry selection	1:E.OC1 to 3			"	"	×
			2:E.OV1 to 3	0
selection			3:E.OC1 to 3, E.OV1 to 3
			4:E.OC1 to 3, E.OV1 to 3, E.IPF, E.UVT, E.BF, E.GF, E.OLT, E.OPT, E.OP1 to 3, E.PE,
			E.OS, E.OSD, E.OD, E. MB1 to 7
			5:E.OC1, E.OC3
Operation			101 to 110: With alarm output during retry operation
		Number of retries at	You can set the number of retries to be made when the protective function is activated.
	67		0: Retry not made.	0		"	"	×
		alarm occurrence	1 to 10: Without alarm output during retry operation
	68	Retry waiting time	You can set the waiting time from activation of the protective function to a retry.	1s		"	"	×
			0 to 10s
	69	Retry count display	You can display the cumulative number of successful restarts made by retries when the			"	"	×
			protective function was activated.	0
		erasure	0
	70	Special regenerative	Set to increase the regenerative brake duty when the FR-ABR option is used.	0%		"	"	"
		brake duty	0 to 15%(1.5K or less), 0 to 30%(2.2K or more)

PARAMETERS

Parameter

5

56