40930701TH DRAFT Vesion

126 /

Category

LCD status message

Trouble or status

Remedy

 

 

 

 

 

 

 

Daily status

READY

 

 

Indicates that the face down stacker is full with sheets.

Remove the paper from the stacker.

 

 

 

 

STACKER FULL

 

 

Repair the broker stacker sensor cable.

 

 

 

 

 

 

 

 

REMOVE THE PAPER

 

 

Repeat the insertion and removal of the connector.

 

 

 

 

 

Clean or replace the stacker full sensor.

 

 

ATTENTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

READY

 

 

Indicates that no paper or paper cassette in a tray.

Load a paper or paper cassette to the tray.

 

 

PAPER OUT

 

 

 

 

 

 

 

 

 

 

 

 

mmmmmmmmmm tttttt

 

 

 

 

 

ATTENTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

READY

 

 

IIndicates that, in an attempt to use the third tray, the first or second

Install the displayed tray.

 

 

tttttt INSTALL

 

tray which is the medium of the path is pulled out.

 

 

 

 

 

 

 

 

 

 

 

Indicates that, in an attempt to use the second tray, the first tray which

 

 

 

ATTENTION

 

 

is the medium of the path is pulled out.

 

 

 

 

 

Provisions: The first and second tray should be returned.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

READY

 

 

Requests that a sheet indicated in the first line message is inserted.

Load the requested paper in tray.

 

 

 

 

 

 

 

 

 

mmmmmmmmm tttttt

 

 

 

 

 

ATTENTION

PAPER REQUEST

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

READY

 

 

Indicates that the interpreter detects an error due to the following

Warnig.

 

 

 

 

 

 

ERROR POSTSCRIPT

 

reasons. From this point on, the receiving data is flushed until the

Check the print job format.

 

 

 

 

 

 

 

 

 

completion of a job. It is automatically canceled when job receiving is

 

 

 

ATTENTION

 

 

completed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

READY

 

 

Indicates that the capacity of memory is Overflowed due to the

Press the RECOVER key on the operator panel to release

 

 

 

 

 

 

ERROR MEMORY

 

following reasons. The operation is continued by pressing Recover

the error display.

 

 

 

 

 

 

 

OVERFLOW

 

switch. Additional RAM should be installed or the amount of data be

Install an expansion optional RAM or reduce the amount of

 

 

ATTENTION

 

 

reduced.

print data.

 

 

 

 

 

 

 

 

 

-Too large printing data within one page.

 

 

 

 

 

 

-Too large macro data.

 

 

 

 

 

 

-Too large DLL data.

 

 

 

 

 

 

-Overflow after the compression of frame buffer.

 

 

 

 

 

 

 

 

Page 107
Image 107
Oki 24DX manual 126, Load the requested paper in tray