S3F80JBPRODUCT OVERVIEW

Table 1-1. Pin Descriptions of 32-SOP

 

Pin

Pin

Pin Description

Circuit

32 Pin

Shared

 

Names

Type

 

Type

No.

Functions

 

P0.0–P0.7

I/O

I/O port with bit-programmable pins. Configurable

1

17–24

Ext. INT

 

 

 

to input or push-pull output mode. Pull-up resistors

 

 

(INT0–INT3)

 

 

 

are assignable by software. Pins can be assigned

 

 

(INT4)

 

 

 

individually as external interrupt inputs with noise

 

 

 

 

 

 

filters, interrupt enable/ disable, and interrupt

 

 

 

 

 

 

pending control. SED&R (note) circuit built in P0

 

 

 

 

 

 

for STOP releasing.

 

 

 

 

P1.0–P1.7

I/O

I/O port with bit-programmable pins. Configurable

2

9–16

 

 

 

to input mode or output mode. Pin circuits are

 

 

 

 

 

 

either push-pull or n-channel open-drain type.

 

 

 

 

P2.0–P2.3

I/O

I/O port with bit-programmable pins. Configurable

1

25–28

Ext. INT

 

P2.4–P2.7

 

to input or push-pull output mode. Pull-up resistors

 

29,5,6,8

(INT5–INT8)

 

 

 

can be assigned by software. Pins can be

 

 

(INT9)

 

 

 

assigned individually as external interrupt inputs

 

 

(CIN0-CIN3)

 

 

 

with noise filters, interrupt enable/disable, and

 

 

 

 

 

 

interrupt pending control. SED & R (note) circuit

 

 

 

 

 

 

built in P2-P2.7 for STOP releasing. Also P2.4-

 

 

 

 

 

 

P2.7 can be assigned individually as analog input

 

 

 

 

 

 

pins for Comparator.

 

 

 

 

P3.0

I/O

I/O port with bit-programmable pin. Configurable to

3

30

T0PWM/T0CAP

 

 

 

input mode, push-pull output mode, or n-channel

 

 

(SDAT)

 

 

 

open-drain output mode. Input mode with a pull-up

 

 

 

 

 

 

resistor can be assigned by software.

 

 

 

 

 

 

This port 3 pin has high current drive capability.

 

 

 

 

 

 

Also P3.0 can be assigned individually as an

 

 

 

 

 

 

output pin for T0PWM or input pin for T0CAP.

 

 

 

 

 

 

In the tool mode, P3.0 is assigned as serial MTP

 

 

 

 

 

 

interface pin; SDAT

 

 

 

 

P3.1

I/O

I/O port with bit-programmable pin. Configurable to

4

31

REM

 

 

 

input mode, push-pull output mode, or n-channel

 

 

(SCLK)

 

 

 

open-drain output mode. Input mode with a pull-up

 

 

 

 

 

 

resistor can be assigned by software.

 

 

 

 

 

 

This port 3 pin has high current drive capability.

 

 

 

 

 

 

Also P3.1 can be assigned individually as an

 

 

 

 

 

 

output pin for REM.

 

 

 

 

 

 

In the tool mode, P3.1 is assigned as serial MTP

 

 

 

 

 

 

interface pin; SCLK

 

 

 

 

XOUT, XIN

System clock input and output pins

2,3

 

nRESET

I

System reset signal input pin and back-up mode

6

7

 

 

 

input.

 

 

 

 

TEST

I

Test signal input pin

4

 

 

 

(for factory use only; must be connected to VSS).

 

 

 

 

VDD

Power supply input pin

32

 

VSS

Ground pin

1

 

 

 

 

 

 

 

1-7

Page 25
Image 25
Samsung S3F80JB manual Pin Descriptions of 32-SOP Circuit 32 Pin Shared Names