100, Click VDSL/VDSL Port Configuration | SMC Networks SMC7724M/VSW

CONFIGURING THE SWITCH

Fields and Attributes

•Active Status – Check this box to enable the selected port.

•RDL – Check this box to enable Remote Digital Loopback (RDL.) RDL tests the link between the switch and the CPE by sending out, and returning data through the CPE, over the VDSL link (see “efm-rdl” on page 3-152.)(Default: Disabled.)

•Flow Control – This is EFM flow control and determines the maximum speed of transmission of data from a specific switch VDSL port to the CPE.

(Range 0 - 128 Mbps, default 100 Mbps.)

Notes: 1. If set to 0, this feature is disabled.

2.Since the maximum transmission speed of VDSL ports is lower than 100 Mbps, when this feature is set to default, the actual maximum transmission rate is determined by the EFM profile and the physical link.

•Profile - Configures an EFM profile for the selected port.

Web Interface

Click VDSL/VDSL Port Configuration.

2-100

Image 128

SMC Networks SMC7724M/VSW manual 100, Click VDSL/VDSL Port Configuration

Contents

TigerAccess Extended Ethernet System Page TigerAccess Extended Ethernet System Management Guide Trademarks Contents Contents Command Line Interface Iii Contents Contents Contents Vii Viii Connecting to the Switch Configuration Options Switch Management Required Connections Remote Connections Basic Configuration Console Connection Setting Passwords Setting an IP Address Manual Configuration Switch Management Dynamic Configuration Enabling Snmp Management Access Community Strings Trap Receivers Saving Configuration Settings Managing System Files System Defaults Following table lists some of the basic system defaults Function Parameter Default Pvid EFM Rdsl Configuring the Switch Using the Web Interface Configuring the Switch Navigating the Web Browser Interface Home Button Action Panel Display Main Menu STA Vlan Port Igmp Displaying System Information Fields and Attributes Specify the hostname, location and contact information Command Line InterfaceWeb Interface Setting the IP Address Manual Configuration Web Interface Using DHCP/BOOTP Command Line Interface Enter the following command to restart Dhcp service Configuring the Login PasswordSecurity Renewing Dchp Configuring Radius Logon Authentication Managing Firmware Click System/Radius Command Usage Downloading System Software from a Server To start the new firmware, reboot the system Saving or Restoring Configuration Settings Web Interface Setting the Startup Configuration File Web Interface Copying the Running Configuration to a File Web Interface Reset Use the reload command to reboot the systemDisplaying Bridge Extension Capabilities Example Click System/Bridge Extension Fields and Attributes Main Board Displaying Switch Hardware/Software VersionsEnter the following command Click System/Switch Information Use the following command to display version information Port Configuration Displaying Connection Status This example shows the connection status for Port Configuring Interface Connections Web Interface Setting Broadcast Storm Thresholds Select the interface, and then enter the required settings Configuring Port Mirroring Configuring Port Security Click Port/Port Security Configuration Address Table Settings Displaying the Address Table Command Line Interface Setting Static Addresses Changing the Aging Time This example also sets the aging time to 400 seconds Global setting apply to the entire switch Spanning Tree Protocol ConfigurationManaging Global Settings Configuring the Switch Displaying the current global settings for STA Web Interface Click Spanning Tree/STA Information Configuring the global settings for STA Web Interface Managing Interface Settings Click STA/STA Trunk Information or STA Port Information This example shows the STA attributes for port This example sets the STP attributes for port Vlan Configuration Assigning Ports to VLANs Forwarding Tagged/Untagged Frames Enabling or Disabling Gvrp Global Setting This example enables Gvrp for the switch Displaying Basic Vlan Information Click VLAN/VLAN Base Information Displaying Current VLANs Web Interface Fields and Attributes Command Line Interface Fields and Attributes 104 Creating VLANs This example creates a new Vlan Adding Interfaces Based on Membership Type 102 Adding Interfaces Based on Static Membership Configuring Vlan Behavior for Interfaces Creating Vlans 100 Configuring Private VLANs Configuring Uplink and Downlink PortsThis example enables private VLANs Enabling Private VLANs 9-16 17-24 25 Creating Vlans Command Line Interface Class of Service Configuration Setting the Default Priority for Interfaces This example assigns a default priority of 5 to port Mapping Priority Classes to Egress Queues Priority Level Traffic Type Fields and Attributes Queue Scheduling 127 Click Priority/Queue Scheduling Mapping Layer 3/4 Priorities to CoS Values Mapping IP Precedence Web Interface 131 Mapping Dscp Priority Web Interface Mapping IP Port Priority 130 Copy Priority Settings Port Trunk Configuration Port Trunk Configuration 142 Configuring Snmp Setting Community Access Strings Access Mode Specifying Trap Managers Multicast Configuration Configuring Igmp Parameters Multicast Configuration Web Interface Interfaces Attached to a Multicast Router 117 Specifying Interfaces Attached to a Multicast Router 122 Displaying Port Members of Multicast Services Adding Multicast Addresses to VLANs Showing Device Statistics Showing Device Statistics This example shows statistics for port Rate Limit Configuration 163 Vdsl Configuration Vdsl Global Configuration Fields and Attributes Vdsl Port Configuration Click VDSL/VDSL Global Configuration Click VDSL/VDSL Port Configuration 100 Configuring a User-specified EFM Profile 101 102 Click VDSL/VDSL Profile User Specified Vdsl Port Link Status 103 104 Click VDSL/VDSL Port Link Status 105 156 Click VDSL/VDSL Port Ethernet Statistics Displaying Vdsl Port Ethernet Statistics106 107 108 Using the Command Line Interface Accessing the CLI Telnet Connection Keywords and Arguments Entering CommandsThis section describes how to enter CLI commands Minimum Abbreviation Command CompletionGetting Help on Commands Showing Commands Command show interfaces ? displays the following information Partial Keyword Lookup Negating the Effect of CommandsUsing Command History Understanding Command Modes Exec Commands Configuration Commands Command Line Processing Keystroke Function Command Groups Command Description Group 163 General Commands LC Line Configuration, VC Vlan Database Configuration Enable Syntax enable levelDefault Setting Command Mode Disable Related Commands Configure Show historyEnd Normal Exec, Privileged Exec Reload Use this command to restart the systemThis command resets the entire system This example shows how to reset the switch Use this command to return to Privileged Exec modeEnd Exit Quit Use this command to exit the configuration programThis example shows how to quit a CLI session Flash/File Commands Copy Privileged Exec Following example shows how to download a configuration file Use this command to delete a file or image Filename Name of the configuration file or image nameDelete Syntax Dir Use this command to display a list of files in Flash memorySyntax Dir boot-rom config opcode filename Whichboot Following example shows how to display all file information Boot system Syntax Boot system boot-rom config opcode filenameGlobal Configuration Dir whichboot System Management Commands Command Function Mode Name The name of this host. Maximum length 255 characters HostnameSyntax Hostname name no hostname Username Enable password Default is level Default password is super Default Setting Command Mode Ip http portSyntax Ip http port port-numberno ip http port Ip http server Syntax Ip http server no ip http server Default Setting Syntax Logging on no logging on Default SettingIp http server Logging on Logging history Logging history clear logging Flash errors level 3 RAM warnings level 7 Snmp-server enable traps snmp-server hostUse this command to clear messages from the log buffer Clear logging Syntax Show logging flash ram Show loggingShow logging Show startup-config Show running-config Show running-config Show startup-config Show users Use this command to display system informationShow system Show version Radius Commands Authentication login Hostipaddress IP address of server Enable password for setting the local passwordRadius-server host Radius-server port Radius-server keySyntax Radius-server port portnumber no radius-server port Syntax Radius-server key keystring no radius-server key Radius-server timeout Radius-server retransmit Show radius-server Snmp Commands Snmp-server community Snmp-server contact Snmp-server locationSyntax Snmp-server contact string no snmp-server contact Syntax Snmp-server location text no snmp-server location Snmp-server host Snmp-server enable traps Issue all traps Use this command to check the status of Snmp communications Show snmp Command Usage IP Commands IP address Netmask Interface Configuration VlanIp address Use this command to submit a Bootp or Dchp client request Ip dhcp restart Ip default-gateway Syntax Ip default-gateway gateway no ip default-gatewayGateway IP address of the default gateway Following example defines a default gateway for this device Use this command to display the settings of an IP interface Show ip interfaceShow ip redirects All interfaces Syntax Ping host size sizecount count This command has no default for the hostPing Interface Line Commands Login Syntax Login local no loginLine Syntax Line console vty Password Line ConfigurationUsername password Syntax Password 0 7 password no password Exec-timeout Login password-threshSyntax Exec-timeout seconds no exec-timeout CLI No timeout Telnet 10 minutes Password-thresh To set the timeout to 120 seconds, enter this commandSyntax Password-thresh threshold no password-thresh Default value is three attempts Default value is no silent-time To set the silent time to 60 seconds, enter this commandSilent-time Syntax Silent-time seconds no silent-time To specify 7 data bits, enter this command DatabitsSyntax Databits 7 8 no databits Seven data bits per character Eight data bits per character Parity SpeedSyntax Parity none even odd no parity Syntax Speed bps no speed To specify 57600 bps, enter this command To specify 2 stop bits, enter this commandStopbits 9600 bps Use this command to display the terminal line’s parameters To show all lines, enter this commandShow line Syntax Show line console vty Interface Commands Interface Description Following example adds a description to Ethernet port Interface Configuration Ethernet, Port ChannelSpeed-duplex Negotiation Negotiation no negotiation Capabilities Flow control enabled Following example enables flow control on portFlowcontrol Flowcontrol no flowcontrol Shutdown Port-channel channel-idRange Default SettingClear counters Switchport broadcast Following example disables Vdsl portInterface Configuration Ethernet Packets per second Syntax Show interfaces status interface Use this command to display the status for an interfaceShow interfaces status Use this command to display interface statistics Show interfaces counters Show interfaces switchport Shows all interfaces Address Table Commands Bridge address Action Show bridge Bridge-group- Bridge group index bridge Clear bridge Bridge-group aging-timeSyntax Clear bridge bridge-group Seconds Show bridge group aging-time All port security is disabled This example enables port security for portPort security Port security no port security Spanning Tree Commands Spanning tree is enabled Bridge spanning-tree Use this command to configure globally for this switch. Use Bridge forward-time Bridge hello-time Bridge max-age Bridge priority 32768 Bridge-group path-cost Bridge-group priority 128 Disabled Bridge-group portfast Use this command to show the spanning tree configuration Show bridge group Vlan Commands Vlan database By default only Vlan 1 exists and is active Vlan Database ConfigurationVlan Show vlan Interface vlan Syntax Interface vlan vlan-id Switchport mode Syntax Switchport mode trunk hybrid no switchport modeAll ports are in hybrid mode with the Pvid set to Vlan Configures Vlan membership mode for a port Switchport acceptable-frame-types Switchport ingress-filteringSwitchport mode All frame types Switchport native vlan Switchport allowed vlan Switchport forbidden vlan No VLANs are included in the forbidden list Use this command to show Vlan information Following example shows how to display information for VlanShow vlan Syntax Show vlan id vlan-idname vlan-name Pvlan Commands For the two commands Disabled with no Pvlan interfacesPvlan Syntax Pvlan For the 12-Line Vdsl Switch Syntax Show pvlan Command Mode Show pvlan Gvrp and Bridge Extension Commands Switchport gvrp Show gvrp configurationSyntax Switchport gvrp No switchport gvrp Default Setting 109 Garp timer 110 Show garp timer Show garp timerShows all Garp timers 111 Garp timer Bridge-ext gvrp112 Bridge-ext gvrp no bridge-ext gvrp Show bridge-ext 113 Igmp Snooping Commands 114 Following example enables Igmp snooping Ip igmp snoopingIp igmp snooping vlan static 115 Igmp Version Ip igmp snooping version116 117 Show ip igmp snoopingShow bridge multicast Ip igmp snooping querier no ip igmp snooping querier Ip igmp snooping querier118 Following shows how to configure the query count to Ip igmp snooping query-countIp igmp snooping query-interval 119 120 Seconds The report delay advertised in Igmp queries. RangeIp igmp snooping query-max-response-time Switch must be using IGMPv2 for this command to take effect Ip igmp snooping query-time-out121 Ip igmp snooping version 122 No static multicast router ports are configuredIp igmp snooping vlan mrouter Displays multicast router ports for all configured VLANs Show ip igmp snooping mrouter123 Syntax Show ip igmp snooping mrouter vlan vlan-id Priority Commands 124 Switchport priority default 125 Queue bandwidth 126 Show queue bandwidth Queue cos-map127 128 Show queue cos-map Use this command to show the class of service priority map Show queue bandwidthShow queue cos-map 129 Map ip port no map ip port Map ip port Global Configuration130 Map ip port Interface Configuration Map ip precedence Global Configuration131 Map ip precedence no map ip precedence 132 Map ip precedence Interface ConfigurationList below shows the default priority mapping Map ip dscp no map ip dscp Map ip dscp Global Configuration133 Map ip dscp Interface Configuration 134 Use this command to show the IP port priority map Show map ip port135 Map ip port Maps CoS values to IP ports i.e., TCP/UDP ports Use this command to show the IP precedence priority map Show map ip precedence136 Map ip precedence Maps CoS values to IP precedence values Use this command to show the IP Dscp priority map Show map ip dscp137 Map ip dscp Maps CoS values to IP Dscp values Mirror Port Commands Interface Configuration Ethernet, destination portPort monitor 138 139 Show port monitor Syntax Show port monitor interface Show port monitor140 Port Trunking Commands 141 Interface port-channel Channel-group142 Syntax Channel-group channel-idno channel-group Use this command to show trunk information No defaultShow interfaces status port-channel 143 Lacp 144Following shows information on Trunk Lacp no lacp 145 Vdsl Commands 146 Efm profile global 147Syntax Efm profile global profile name Profile name Name of the profile 148 Efm profile 149Efm profile Syntax Efm profile profile name Interleaving is disabled Efm define user-profile150 Efm profile global efm profile Efm reset Syntax Efm reset local remoteUse this command to troubleshoot EFM port performance Efm shutdown Syntax Efm rdl no efm rdl Default Setting Efm rdl152 Off Rate-limit global rate-limit Efm flow-control153 Show controllers ethernet-controller 154Syntax Show controllers ethernet-controller interface-id Interface-id- ID of the EFM port 155 Clear controllers ethernet-controller Show controllers efm interface-id actual 156 157 Show controllers efm interface-id adminSyntax Show controllers efm interface-idadmin dsrate usrate Syntax Show controllers efm profile mapping names Show controllers efm profile158 159 Examples Show controllers efm status 160 161 Show controllers efm remote ethernet mode Use this command to display the connected CPE Ethernet modeTo obtain the Ethernet mode from CPE side Vdsl chip 162 Rate Limit Commands Rate-limit global163 Rate-limit input no rate-limit input Rate-limit interface 164Syntax Rate-limit input rate Rate The rate unit is Mbps Appendix a Troubleshooting Troubleshooting Chart Upgrading Firmware via the Serial Port Upgrading Firmware VIA the Serial Port Troubleshooting Console Port Pin Assignments DB-9 Port Pin Assignments Console Port to 9-Pin DTE Port on PC Console Port to 25-Pin DTE Port on PC Auto-negotiation Glossary-11000BASE-T Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Index-1 Index-2 Page For Technical SUPPORT, Call