Telex ISP-100 - page 111

8-41

Processing Components - Gain

(i.e. after the master attenuator). A green LED indicates that the

meter information is pre-fader. Clicking on the button will toggle the

setting.

Contents

Main Page Page ii CUSTOMER SUPPORT RETURN SHIPPING INSTRUCTIONS Procedure for Returns Shipping to Manufacturer for Repair or Adjustment iii End-User License Agreement for Telex Software iv INTRODUCTION .................................................................... 1-1 SETUP & INSTALLATION...................................................... 2-1 TROUBLESHOOTING ............................................................ 3-1 SPECIFICATIONS .................................................................. 4-1 v vi INSTALLING VUE-IT........................................................... 5-1 GETTING STARTED............................................................... 6-1 USING VUE-IT .......................................................................7-1 vii PROCESSING COMPONENTS ...............................................8-1 viii ix Page 1-1 INTRODUCTION An Overview of the ISP-100 1-2 2-1 SETUP & INSTALLATION Introduction Unpacking Front Panel Features (see Figure 2-1) 2-2 Rear Panel Features (see Figure 2-2) Power Requirements Operating Environment Rack Mounting 2-3 Card Installation Procedure 2-4 Cable Diagrams 2-5 2-6 2-7 2-8 2-9 Page 3-1 TROUBLESHOOTING User Modifications In Case of Problems 3-2 Diagnostics Factory Default Mode 3-3 Retrieving Version Numbers Retrieving Serial Numbers 3-4 Changing the Fuse Changing the Battery WARNING: 3-5 3-6 Technical Support Procedure for Returns 3-7 Shipping to Manufacturer for Repair or Adjustment Page 4-1 SPECIFICATIONS Components 4-2 4-3 ISP-100 Component Plots Page Page 4-6 MIM-1 & MIM-2* Analog Input Modules * MIM-2 differences parenthetically noted. (Unless otherwise specified measurements are at unity gain with +16 dBu signal. 4-7 MOM-1 Analog Output Module 4-8 MDM-1 AES/EBU Digital I/O Module (Sample Rate Converter Engaged) 4-9 (Sample Rate Converter bypassed) 4-10 Physical Power 5-1 INSTALLING VUE-IT NOTE: Minimum System Requirements Identifying a Serial Port 5-2 Updating the ISP-100s Operating System 5-3 5-4 Configuring the Software 5-5 Page 6-1 GETTING STARTED Starting VUE-IT 6-2 Starting a New Project 6-3 VUE-IT File System 6-4 7-1 Using VUE-IT File (see Figure 7-1) 7-2 Edit (see Figure 7-2) Options (see Figure 7-4) Tools (see Figure 7-3) 7-3 7-4 System Configurations (see Figure 7-8) 7-5 Project Manager 7-6 7-7 7-8 7-9 7-10 QuickSET Manager 7-11 GPI 7-12 7-13 QuickMAP QuickMAP Component Bypassing 7-14 I/O Properties (see Figure 7-21) 7-15 7-16 Note: 7-17 Device Status Panel Page 8-1 PROCESSING COMPONENTS 8-2 Combine 8-3 8-4 Compressor 8-5 8-6 8-7 8-8 8-9 8-10 8-11 Crossover 8-12 8-13 8-14 8-15 8-16 Journal of the Audio Engineering Society 8-17 8-18 8-19 Journal of the Audio Engineering Society 8-20 8-21 8-22 8-23 8-24 Cut 8-25 8-26 Delay 8-27 Dither 8-28 8-29 Filter 8-30 8-31 8-32 8-33 8-34 8-35 Journal of the Audio Engineering Society 8-36 8-37 8-38 8-39 Gain 8-40 Page 8-42 Gate 8-43 8-44 8-45 8-46 Limiter 8-47 8-48 each 8-49 not 8-50 8-51 8-52 Select A-1 GLOSSARY A-2 A-3 Page B-1 STANDARD QUICKMAPS Identification of Slots and Connectors Applying QuickMAPs