Telex ISP-100 8-25

8-25

Processing Components - Cut

Fine (F) or Coarse (C) Control

This button determines the increment/decrement associated with the

UP/DOWN arrows. Fine produces small steps in value, while Coarse

provides large steps in value. Clicking on the button will toggle the

setting.

Polarity Control (+/-)

This button determines the polarity of the signal. A + indicates that

the signal will not have it’s phase altered. A - indicates that the

signal’s phase will be changed 180. Clicking on the button will toggle

the setting.

Mute Control (M)

This button determines if the input signal will be muted. A black M

indicates that the signal is not muted, while a red M indicates that the

signal is muted. Clicking on the button will toggle the setting.

Bypass Control (master)

This button determines if the component is in the processing chain. If

the LED on the button is gray, then the component is inserted into

the signal processing chain. If the LED is red, then the component is

bypassed in the signal processing chain. A bypassed component will

be colored red in the QuickMAP.

Contents

Main Page Page ii CUSTOMER SUPPORT RETURN SHIPPING INSTRUCTIONS Procedure for Returns Shipping to Manufacturer for Repair or Adjustment iii End-User License Agreement for Telex Software iv INTRODUCTION .................................................................... 1-1 SETUP & INSTALLATION...................................................... 2-1 TROUBLESHOOTING ............................................................ 3-1 SPECIFICATIONS .................................................................. 4-1 v vi INSTALLING VUE-IT........................................................... 5-1 GETTING STARTED............................................................... 6-1 USING VUE-IT .......................................................................7-1 vii PROCESSING COMPONENTS ...............................................8-1 viii ix Page 1-1 INTRODUCTION An Overview of the ISP-100 1-2 2-1 SETUP & INSTALLATION Introduction Unpacking Front Panel Features (see Figure 2-1) 2-2 Rear Panel Features (see Figure 2-2) Power Requirements Operating Environment Rack Mounting 2-3 Card Installation Procedure 2-4 Cable Diagrams 2-5 2-6 2-7 2-8 2-9 Page 3-1 TROUBLESHOOTING User Modifications In Case of Problems 3-2 Diagnostics Factory Default Mode 3-3 Retrieving Version Numbers Retrieving Serial Numbers 3-4 Changing the Fuse Changing the Battery WARNING: 3-5 3-6 Technical Support Procedure for Returns 3-7 Shipping to Manufacturer for Repair or Adjustment Page 4-1 SPECIFICATIONS Components 4-2 4-3 ISP-100 Component Plots Page Page 4-6 MIM-1 & MIM-2* Analog Input Modules * MIM-2 differences parenthetically noted. (Unless otherwise specified measurements are at unity gain with +16 dBu signal. 4-7 MOM-1 Analog Output Module 4-8 MDM-1 AES/EBU Digital I/O Module (Sample Rate Converter Engaged) 4-9 (Sample Rate Converter bypassed) 4-10 Physical Power 5-1 INSTALLING VUE-IT NOTE: Minimum System Requirements Identifying a Serial Port 5-2 Updating the ISP-100s Operating System 5-3 5-4 Configuring the Software 5-5 Page 6-1 GETTING STARTED Starting VUE-IT 6-2 Starting a New Project 6-3 VUE-IT File System 6-4 7-1 Using VUE-IT File (see Figure 7-1) 7-2 Edit (see Figure 7-2) Options (see Figure 7-4) Tools (see Figure 7-3) 7-3 7-4 System Configurations (see Figure 7-8) 7-5 Project Manager 7-6 7-7 7-8 7-9 7-10 QuickSET Manager 7-11 GPI 7-12 7-13 QuickMAP QuickMAP Component Bypassing 7-14 I/O Properties (see Figure 7-21) 7-15 7-16 Note: 7-17 Device Status Panel Page 8-1 PROCESSING COMPONENTS 8-2 Combine 8-3 8-4 Compressor 8-5 8-6 8-7 8-8 8-9 8-10 8-11 Crossover 8-12 8-13 8-14 8-15 8-16 Journal of the Audio Engineering Society 8-17 8-18 8-19 Journal of the Audio Engineering Society 8-20 8-21 8-22 8-23 8-24 Cut 8-25 8-26 Delay 8-27 Dither 8-28 8-29 Filter 8-30 8-31 8-32 8-33 8-34 8-35 Journal of the Audio Engineering Society 8-36 8-37 8-38 8-39 Gain 8-40 Page 8-42 Gate 8-43 8-44 8-45 8-46 Limiter 8-47 8-48 each 8-49 not 8-50 8-51 8-52 Select A-1 GLOSSARY A-2 A-3 Page B-1 STANDARD QUICKMAPS Identification of Slots and Connectors Applying QuickMAPs