Timing parameters, Static signals | Texas Instruments TMS380C26

TMS380C26

NETWORK COMMPROCESSOR

SPWS010A±APRIL 1992±REVISED MARCH 1993

PARAMETER MEASUREMENT INFORMATION

timing parameters

The timing parameters for all the pins of TMS380C26 are shown in the following tables and are illustrated in the accompanying figures. The purpose of these figures and tables is to quantify the timing relationships among the various signals. The parameters are numbered for convenience.

static signals

The following table lists signals that are not allowed to change dynamically and therefore have no timing associated with them. They should be strapped high or low as required.

SIGNAL			FUNCTION

			Host processor select. (Intel/Motorola)
SI/M

CLKDIV			Reserved

BTSTRP			Default bootstrap mode. (RAM/ROM)

PRTYEN			Default parity select. (enabled/disabled)

TEST0			Test pin, indicates network type

TEST1			Test pin, indicates network type

TEST2			Test pin, indicates network type

TEST3			Test pin for TI manufacturing test. ²
TEST4			Test pin for TI manufacturing test. ²
TEST5			Test pin for TI manufacturing test. ²

²For unit-in-place test.

timing parameter symbology

Timing parameter symbols have been created in accordance with JEDEC standard 100. In order to shorten the symbols, some of the pin names and other related terminology have been abbreviated as shown below:

DR	DRVR		RS	SRESET
DRN			VDD	VDDL, VDDB
	DRVR
OSC	OSCIN
SCK	SBCLK

Lower case subscripts are defined as follows:

c	cycle time	r	rise time
d	delay time	sk	skew
h	hold time	su	setup time
w	pulse duration (width)	t	transition time

The following additional letters and phrases are defined as follows:

H	High	Z	High impedance
L	Low	Falling edge	No longer high
V	Valid	Rising edge	No longer low

POST OFFICE BOX 1443 •HOUSTON, TEXAS	33
77251±1443

Image 33

Texas Instruments TMS380C26 specifications Timing parameters, Static signals, Timing parameter symbology, Signal Function

Contents

Attached System Bus LAN Subsystem Network Commprocessor PIN Quad Flat Pack TOP View Pinout Description Block diagram and signal descriptions TMS380C26 Terminal FunctionsPIN Name Description AX1 AX0 MaxphMaxpl AX3 AX2 Mreset OUT SresetMOE Mras NSELOUT0 NSELOUT1 Prtyen Sbhe = H Sddir Direction DIO DMA ShrqSintr SWR SRD = Selects 8-bit mode see Note 108 Reserved. This signal must be left unconnected see Note= Selects 16-bit mode Syncin System Interface ± Motorola Mode SI/M = LSBHE/ Srnw Sbgr Terminal Functions = LSbrq Sirq Suds SdtackSlds Nsrt FRAQ/TXDPxtalin RCVR/RXD Lpbk TXCColl Terminal Functions VSS1 VSS2 VsslVSS3 VSS4 VSS5 VSS6 Architecture Communications processor CPSystem interface SIF Protocol handler PH Memory interface MIF Clock generator CG Adapter support function ASF Address Description Adapter-Internal Pointers for Token-Ring² Adapter-Internal Pointers for Ethernet ² ³ 68xxx Mode is always 16-bit User-Access Hardware RegistersWord Transfers Byte Transfers Bit 5 Swddir Ð Current Sddir Signal Value Bits 0-2 Test 0±2. Value on Test 0±2 pinsSIF Adapter Control Register Sifacl Sifacl Register Bit 7 Psdmaen Ð Pseudo-System-DMA Enable Bit 6 Swhrq Ð Current Shrq Signal ValueBit 8 Areset Ð Adapter Reset Bit 10 Boot Ð Bootstrap CP Code Bit 13 PEN Ð Adapter Parity Enable Bit 12 Sinten Ð System-Interrupt EnableBit 14 Ð 15 Nselout 0±1 Ð Network selection outputs System Psdmaen Swhrq Swhlda Sinten Interrupt Result Systeminterrupt SINTR/SIRQ Sifacl Control for Pseudo-DMA OperationDMA SHRQ/SBRQ Dmadir Sddir Swhlda Swddir Swhrq Psdmaen Sinten MIN NOM MAX Unit Recommended operating conditionsParameter Test Conditions MIN TYP MAX Unit See Note High Low Test measurementVload IOL Output Under Test Reference Periods WhenClkdiv = Oscout MBCLK1² MBCLK2² Timing parameter symbology Static signalsSignal Function Timing parameters Parameter MIN MAX Unit 289² ThRST Hold time of DMA size from High Intel mode onlyReaches minimum high level HVDDH-RSL 118² Pulse duration High Minimun VDD High Level VDD Sbclk Oscin MBCLK1 MBCLK2 Sreset S8/SHALT103 101 106 104 105 102 107 110 108 109 111 117 118 119 288 289 Mreset 126 Delay time from MBCLK1 no longer low to ValidNMI 121 Hold time Valid after MBCLK1 low Mreset MBCLK1 MBCLK2 MAX0 MAX2 ADD/EN Mromen Maxph MaxplMADH0±MADH7 Memory bus timing clocks, MRAS, MCAS, and MAL to Address MADL0±MADL7 Maxph MaxplMromen MAL Address Column RowAddress Status Column Status Mcas MOE Memory bus timing read cycleMaxph Maxpl MADH0±MADH7 Maxph Maxpl Mras Mcas MAX0 MAX2 MromenAddress Status Data/Parity Mbiaen Memory bus timing write cycle MAX0, Address Enable AddressMAX2 Mromen Mras Mcas Mben Parameter MIN Memory bus timing TMS380C26 releases control of bus MBCLK1 MBCLK2 Mben 75a 74aMddir MAL Mbiaen Mbrq Mbgr Setup time High before MBCLK1 rising edge, bus resume Memory bus timing TMS380C26 resumes control of busHold time Valid after MBCLK1 low, bus resume Memory Bus Timing TMS380C26 Resumes Control of Bus Mben Mddir MAL Mbiaen Mbrq Mbgr Memory bus timing external bus master read from TMS380C26 MacsHold time Low after MBCLK2 low, external bus master read MBCLK1 MBCLK2 MAX0 MAX2 Maxph Maxpl MADH0±MADH7Mddir Macs Memory bus timing external bus master write to TMS380C26 MAX0, MAX2 Maxph MaxplData/Pty MADL0±MADL7 Mras Memory bus timing Dram refresh timing73a Mcas Mref Bit Xmatch and Xfail timing127 128 Xmatch Xfail Parameter MIN TYP MAX Unit Token ring Ð ring interface timingRclk Rcvr Rclk or Pxtalin Token ring Ð transmitter timing see FigureDrvr 160 159 Ethernet timing of Xmit signals Ethernet timing of clock signalsTXD Txen CRS Ethernet timing of RCV signals Ð start of frameRXC RXD Crshld Ethernet timing of RCV signals Ð end of frame320 321 322 Ethernet timing of RCV signals Ð no RXC NorxcTXD Txen TXC TXD 350Data JAM 80x8x DIO read timing SRS0± SRS2 Sbhe SCS, SrsxSras Sdben 80x8x DIO write timing 267 272a 280 281 Valid 264 265 268 256281a 282W 283W 276 279 275 282b 80x8x interrupt acknowledge timing ± second Siack pulse 80x8x interrupt acknowledge timing ± first Siack pulseSRD, SWR SCS Siack 287 First 286 Second Sddir High SCS, Srsx SRS0±SRS2 Sbhe Siack SWR SRDSdben SRDY²HI-Z SADH0±SADH7 SADL0±SADL7,HI-ZSPH, SPL Sown 80x8x mode bus arbitration timing, SIF takes controlSRD SWR SWR Sown Sbbsy Shlda SRD, SWRSADL0±SADL7 SPH, SPL 212 Delay from Sbclk low to address valid 214 ² After Sbclk low to guarantee recognition on this cycleThis cycle 208b High TwSCKL ± Sbclk Sras Slds 80x8x mode DMA write timing SADL0±SADH7 SRD HighSADH0±SADL7 SPH, SPL Sddir High 80x8x mode bus arbitration timing, SIF returns control Sbrls Sown 80x8x mode bus release timingTW or 208c 68xxx DIO read timing Siack Srnw SRS0, SRS1Suds Slds SDTACK²HI-Z SADH0±SADH7 SADL0±SADL7,HI-Z SPH, SPL Suds Slds Sdtack 68xxx DIO write timing SDBEN³ SCS SRSX, SRS0, SRS1 Siack SrnwSDTACK² SADH0±SADH7 SADL0±SADL7,HI-Z SPH, SPL SCS Siack 68xxx interrupt acknowledge cycle timingSCS Srnw Sdtack Siack Sdtack Sdben SDTACK² HI-Z SCS, Srsx SRS0, SRS1 Sbhe Siack Srnw SldsSADH0±SADH7 SADL0±SADL7, HI-ZSPH, SPL 275 282a 255 241 Delay from Sbclk high in TX cycle to High 68xxx mode bus arbitration timing, SIF takes controlSbgr Sbrq SAS, Slds Sberr Sdtack SbbsySuds Srnw SADH0±SADH7 HI-Z SADL0±SADL7 SPH, SPL 237R Delay from Sbclk high in the T2 cycle to Low 68xxx mode DMA read timingOn this cycle 208b Suds SAS Sale SADL0±SADH7 SADH0±SADL7 SPH, SPL Sdben Suds Slds 68xxx mode DMA write timing SADL0±SADH7, SADH0±SADL7 SPL, SPH SAS 240 ² Setup SRNW, 68xxx mode bus arbitration timing, SIF returns control Read HI-Z Write Sbclk Sbgr SdtackSIF HI-Z Write Read Sown Sberr 68xxx mode bus release and error timingSbrls Sown Sberr Sdtack Normal completion with delayed start² Rerun cycle with delayed start²Sbclk Sdtack Sberr Shalt TH B TH E Sbclk Sdtack Sberr Shalt Sown 254 0.010 NOM 635 0.025 NOM 76 0.030 NOM Jedec plastic leaded quad flat package PQ suffixJedec NO. Outline Terminals MIN MAX MO±069±AD Important Notice