Agilent Technologies 85330A manual

		Service
		Assembly and Disassembly
Switch Control Unit	Disassembly
	1.	Remove the Local Control cable and Switch Drive cable.
	2.	Remove the four screws from the lid of the Switch Control Unit.
	3.	Pull the unit apart.

CAUTION	Be careful not to damage the gasket seal in each module.
	4.	Remove the ribbon cable from the Drive module and the Decoder
	4.
		module.
	5.	Do not change any switch settings in any of the modules!

Assembly

1.If you are installing a new Decoder or Driver module, the switches S1 and S2 must be set correctly. If you are replacing a module, set the switches for the same setting as the old module. If you are unsure, here arte the factory default settings:

❍The Decoder module switches are normally factory set to “all closed” for S1 and S2.

❍The Driver module switches are normally factory set to “all closed” for S1 and S2.

2.Check PAL U2 and U3 in sockets XU2 and XU3 on the Driver module. The module should contain both PALs, unless there is more than one driver module. If the SCU has more than one driver module, then only the ﬁrst (bottom) should have both XU2 and XU3 ﬁlled with a PAL. Any modules after the ﬁrst should only have PAL U2 installed. Remove PAL U3 from socket XU3 for these modules.

3.Make sure that the gasket seal is properly installed in each module housing.

4.Install the A5-A6 ribbon cable as follows:

a.Plug the 16 pin connector into the decoder board socket J3.

b.Plug the 14 pin connector into the decoder board socket J4.

c.Insert the free end of the cable with the 30-pin connector through the large notch in the driver board from the bottom.

d.Lower the Driver module onto the Decoder module, pulling the ribbon cable through the opening.

e.Plug the 30 pin connector into the driver board socket J1.

f.Pull the excess length of the ribbon cable up from the Decoder module into the Driver module. Fold the excess length of the cable over the top of the driver board.

85330A Multiple Channel Controller

9-21

Image 150

Agilent Technologies 85330A service manual Remove the Local Control cable and Switch Drive cable

Contents

Agilent Technologies 85330A Multiple Channel Controller Restricted Rights Legend What You’ll Find in This Manual… Chapter Warranty Certiﬁcation Documentation Warranty Assistance Service and Support Europe Safety and Regulatory Information Instrument Markings Safety Earth Ground Viii Manufacturers Declaration Sound Emmisions Declaration of Conformity Typeface Conventions Xii Contents Operator’s Check Manual Operation Case of Difficulty Accessory Documentation Glossary Xviii85330A Multiple Channel Controller Installation Installation at a Glance Preparing the Main Antenna Measurement System Installing the Agilent 85330A Multiple Channel ControllerHow to use the ﬁgure Choosing the Proper Conﬁguration Flow Chart for Choosing the Correct Installation 85330A Installation Diagram for 8530A Source Control 85330A Installation Diagram for Fast TTL Source Control Checking Operation of the Multiple Channel Controller Loading the Driver from a Personal ComputerEquipment Needed Procedure Ibasic is only present if the Ibasic option is installed Selecting Positive or Negative-Edge Event Triggers Refer to -4 on Positive/Negative-Edge Event Trig jumpers Installing the Switch Control Units and Switches SCU and Switch Mounting Diagram Installing the Switch Control Units and Switches This Chapter Description Recommended Equipment Required Equipment Setting Up the Equipment Performance Veriﬁcation TestSystem Digital Oscilloscope Network Analyzer Cables Calibration Save Setup Measurement Display Turn-On Switch Control Unit VoltagesVerifying the Multiple Channel Controller Voltage Check Inputs/Outputs Output Trigger Test Pulse Receive and Cycle Test Counter Pulse Delay Test Counter Pulse Delay Test Setup Measurement Busy Signal and Pulse Width Test Verifying the Switch Control Unit Verifying the RF Switches Switch Setup Recall Verifying Remote Ports 1 JumpersEquipment Required Remote Port 1 and remote Port 2 Test Procedure AUX 1 and AUX Pulse TestMeasuring Pulses from AUX 1 or AUX When Finished with All Tests Procedure Purpose Operator’s Check General Information Triggering Product DescriptionIn-depth Information Measurement Speed Advantages Lowering the Workload on the Computer Controller Installing the Detachable Power Cord Manual Operation Preparing the 85330A to Control the System Switch ComponentsSwitch control units Special Systems PIN switch modules Downloadable Driver System Interface Required Equipment85383A Local Control Cable 85383B expansion cable 85384A Switch Driver CableAgilent 85383 Wiring Table 85385A Remote Trigger Cable PIN Switches 85331A SP2T PIN Switch85332A SP4T PIN Switch Supplied Equipment and Software Supplied Equipment and Software Environmental Limits Characteristics85330A Multiple Channel Controller Environmental Conditions for the 85330A Dimensions Size and DimensionsVentilation Requirements Front Panel Features Need More Information Rear Panel Features 85330A Rear Panel Connectors Rcvr Ready Remote 1 Switch Port 1 AUX Power Compatible RF Sources 85330A CompatibilityCompatible LO Sources Required Options for Agilent 836xx LO Sources 85330A Compatibility Manual Operation To Use the Front Panel About the Softkeys Menus Utility Keys Softkey Map 85330A Softkey Menu Map To View or Change the 85330’s Gpib Address Changing the Gpib Address To Close Any Switch in the System to select a channel More about Switch Addresses To View the Most Recent Error Message To Change the TTL State of AUX 1 or AUXTo View the Revision of the Downloaded Driver To Perform Service Functions To View Custom Option Number If ApplicableTo Manually Send Trigger Pulses To View Custom Option Number If Applicable This Chapter Gpib Addresses Long and Short Command Syntax 6Programming SCU address Switch addressDeﬁnition of Terms Channel How to Use the Figure To Choose a Measurement Conﬁguration CW Measurement Conﬁguration Description To Use this Conﬁguration 8530A settings Single Source Multiple-Frequency Conﬁguration 85330A settings Dual Source Multiple-Frequency Measurements 8530A Control of Sources Source settings Fast Source Control Selecting a Channel Other examples This example Number of Angular Increments Events List of Switch States To Use Run-Time Control ModeSetup 85330A Multiple Channel Controller Event Triggering Number of Frequency Points Switch Settling Time TTL Trigger and Ready Timeouts Select Switch State Idle Switch List Loop Event TriggerReceiver Ready Run-Time Flow Chart with Programming Command References Frequency Loop Event Loop Using IMM vs. TTL Trigger for Source Run-Time Measurement Sequence for Multiple Controllers To Use Run-Time Control Mode To Use Run-Time Control Mode Programming Examples Example Pairs Repeat Wait Until the Receiver is Ready to Is the Current Point RE-SAVE EX2 Output @RecLISFREQ Soft Reset If PassesAnglepts then RE-SAVE EX3 Assign HP 8530A HP-IB Output @RfSYSTLANG Scpi Output 1194 85330A Error Messages 1305 Not enough driver RAM for this driver 85330A Error Messages Command Syntax Common Command Format Standard Command Format Abbreviated Commands ParametersParameter Types Common Commands Default Syntax ExampleSyntax Example Default OPC? Default Syntax Standard Command ReferenceSubsystem Command Syntax ROUTe ROUTeDELay ROUTeCONTrol Subsystem Command Syntax RUNTime RUNTimeCONTroller RUNTimeEVENtCOUNt TTL Mode IMM Mode Default Syntax Example RUNTimeEVENtTRIGger RUNTimeINITiateIMM RUNTimeSOURceCOUNt RUNTimeSOURceSOURCE1TRIGger RUNTimeSOURceSOURCE2TRIGger RUNTimeSWITchDELay RUNTimeSWITchSCAN Sets AUX 2 output to TTL LOW during run-time RUNTimeSWITchTRIGger This command is in revision A.02.31 or greater RUNTimeTIMEoutEVENt RUNTimeTIMEoutRECeiver RUNTimeTIMEoutREMote RUNTimeTIMEoutSOURceSYSTem SYSTemERRor? Read. The *CLS command will clear the error status Standard Command Reference When Turned on 85330A Does Not Show the Main Menu Case of Difficulty Service Introduction Theory of Operation Gpib 85330A Timing Sequence of a Typical Measurement Timing Sequence Trigger Widths Trigger Width Description Theory of Operation Recommended Test Equipment Required Test Equipment Service Troubleshooting Troubleshooting the SystemTroubleshooting Multiple Channel Controller Troubleshooting Troubleshooting the RF Switch Troubleshooting the CablesSwitch Port 1/2 Connector Pinout 85383A Connector Wiring Table 85385A Wiring Replaceable Parts 85330A System Identiﬁcation Diagram 85330A Mainframe Replacement Parts Mainframe, Plug-in Cards RF Switch 85331/2 Switch Control Unit Replacement Parts85331/2 Switch Replacement Parts Replacement Interconnect Cables for 85330/31/32 Interconnect Cables Assembly Assembly and DisassemblyDisassembly Mainframe E1330 Card Conﬁguration Card Conﬁguration Remove the Local Control cable and Switch Drive cable Adjustments Selecting Positive or Negative-Edge Event Triggers Selecting the Multiple Channel Controller’s Gpib Address Switching from the Internal to External Power Supply Required Mating Connector10 AUX Power In Connector Pinouts as looking at rear Preventive Maintenance Preventive Maintenance Accessory Documentation 10-2 Controller Direct ControlFast CW Modes Fast Data Acquisition Modes 85330A System Insertion Loss Operating CharacteristicReceive Switch LO/IF Unit Remote Run-Time Control ModeReceiver System Return Loss Standard System Switch Control UnitSwitch Module Typical Glossary Index Numerics Index-2 Index-3