Allied Telesis X8106 manual Attaching the Bare Grounding Wire to the Grounding Post 156

SwitchBlade x8106 Chassis Switch Installation Guide
Figure 110: Attaching the Bare Grounding Wire to the Grounding Post	156
Figure 111: Securing the Bare Grounding Wire to the Grounding Post	157
Figure 112: Power Wire Terminals	158
Figure 113: Stripping the Power Wires	159
Figure 114: Attaching the Power Wires to the Straight Terminal Lugs	159
Figure 115: On/Off Switch on the AT-SBxPWRSYS1 DC Power Supply	160
Figure 116: Opening the Plastic Cover	161
Figure 117: Removing the Terminal Screws	162
Figure 118: Connecting the Positive (+) Power Wire with a Straight Terminal	163
Figure 119: Connecting the Negative (-) Power Wire with a Straight Terminal	164
Figure 120: Closing the Plastic Cover over the Terminal Connectors	165
Figure 121: Tightening the Handle Locking Screw	166
Figure 122: Stripping the Power Wires	167
Figure 123: Attaching the Power Wires to the Right Angle Terminals	167
Figure 124: Removing the Plastic Cover	168
Figure 125: Removing the Terminal Screws	169
Figure 126: Connecting the Positive (+) Power Wire with a Right Angle Terminal	170
Figure 127: Connecting the Negative (-) Power Wire with a Right Angle Terminal	171
Figure 128: Tightening the Handle Locking Screw	172
Figure 129: Stripping Solid or Stranded DC Power Wires	173
Figure 130: Connecting the Positive Lead Wire	174
Figure 131: Connecting the Negative Lead Wire	175
Figure 132: Switch Initialization Messages	178
Figure 133: Switch Initialization Messages (Continued)	179
Figure 134: Connecting the Management Cable to the Console RS-232 Port	184
Figure 135: SHOW VERSION Command	186
Figure 136: SHOW CARD Command	186
Figure 137: Disconnecting the AC Power Cord from the AC Socket on the Back Panel	206
Figure 138: Lifting the Locking Handle on the Power Supply	207
Figure 139: Removing the Power Supply from the Chassis	208
Figure 140: Installing a Blank Power Supply Slot Cover	209
Figure 141: Lowering the Locking Handle on the Power Supply Slot Cover	210
Figure 142: Loosening the Screw on the Locking Handle	211
Figure 143: Opening the Plastic Window on the Terminal Block	212
Figure 144: Removing the Negative Lead Wire	213
Figure 145: Removing the Positive Lead Wire from the Terminal Block	214
Figure 146: Reinstalling the Screws on the Positive and Negative Terminals	215
Figure 147: Closing the Plastic Cover	216
Figure 148: Removing the Grounding Wire	217
Figure 149: Reinstalling the Nut and Washer on the Grounding Post	218
Figure 150: Lifting the Locking Handle and Removing the Power Supply	219
Figure 151: Installing a Blank Power Supply Slot Cover	220
Figure 152: Lowering the Locking Handle on the Power Supply Slot Cover	221
Figure 153: Loosening the Screw on the AT-SBxFAN06 Fan Module	227
Figure 154: Loosening the AT-SBxFAN06 Fan Module from the Backplane Connector	227
Figure 155: Withdrawing the AT-SBxFAN06 Fan Module 25 mm (1 in.) from the Chassis	228
Figure 156: Removing the AT-SBxFAN06 Fan Module from the Chassis	229
Figure 157: Installing a New AT-SBxFAN06 Fan Module	230
Figure 158: Securing the AT-SBxFAN06 Fan Module on the Backplane Connector	231
Figure 159: Tightening the Screw on the AT-SBxFAN06 Fan Module	231
Figure 160: Pin Numbers for RJ-45 and RJ Point 5 Ports (Front View)	239

11