Manuals / Emerson / Computer Equipment / Switch

Emerson user manual AC8 Specifications

Models: AC8

1 128

Download 128 pages 38.48 Kb

Page 86

Specifications

8.0SPECIFICATIONS

8.1AC8 Specifications

		Transformer Module

		115VAC		230VAC
	Power	UML11500		UML23000
	Requirements	115VAC ±10%		230VAC ±10%
		of nominal;		of nominal;
		60Hz, 4A,		50Hz, 0.5A,
		460VA		115VA
	Dimensions		18 x 2-3/4 x 18
	W x D x H, in. (mm)	(457.2 x 69.85 x 457.2)
	Weight (Assembled)	20.56 lb. (9.33 kg)
	Enclosure Type		NEMA 1
	Liquid Crystal Display (LCD)	Four line, 20 character, backlit
	Mounting Surface	Building Wall or Structural Member
	Ambient Operating	32ºF to 104ºF (0ºC to 40ºC)
	Environment	0% RH to 95% RH (non-condensing)
	Processor Specifics
	Model	Motorola XC68HC812A4

	Clock speed		16MHz
	Total RAM		256Kb

	Total FLASH		4M

	Total EEPROM		4K
	A/D Resolution (Analog IN)		12 Bit

	Modem Type Embedded		14.4K bps

	Clock Type	Real-Time Clock
	Clock battery backup type	Lithium Cell (non-replaceable)

	Clock battery life	7 years, constant, no power

	Modem battery backup type	Nickel Cadmium (replaceable)
	Modem battery life	10 minutes at full load

	Communications
	Local Communications		RS232
	Remote Communications
	Modem (9600-N-8-1)	Baud rate 9600 bps, Parity=None, Data bits=8, Stop bits=1
	Supported pagers	9600 E-7-1 supports TAPI protocol version 1.8
	SiteScan Web	IGM Protocol, EIA422

		Transformer Module
	Agency Listings
	Agency Listings	115VAC		230VAC
		(TM115)		(TM230)
	UL	UL1012		UL1585

	CSA	C22.2 No. 66 and
	CSA	C22.2 No. 107.1
		C22.2 No. 107.1
	CE		Yes

	FCC Compliance		N/A

	Inputs & Outputs (Quantity)
	Digital Inputs (8)	Dry Contact Closure 24VDC, 10 mA

	Analog Inputs (4)	4-20 mA signal input with selectable
	Analog Inputs (4)	power source of 12VDC or 24VDC
		power source of 12VDC or 24VDC
	Digital Outputs (8)		24VAC, 3A

	Common Alarm Outputs (2)		24VAC, 3A

NOTE

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

78

Image 86

Emerson user manual AC8 Specifications

Contents

Site Monitoring and Services AC8Page Table of Contents View Active Alarms Setup System Setup Zones Appendix a Service Terminal Interface Appendix B Default Settings Quick Reference GuideFigures Page Data Logs Methods of Viewing and Configuring the AC8Available Alarms Transformer ModuleOperation LCD for configurationOutside Enclosure Overview Transformer Module Back of LCD Controller BoardLiebert SiteScan Web Typical ConfigurationContact relay Output Humidity Lockout Analog inputsStatus LEDs Controller Board OverviewController board components Description For more information, seeLoss-of-power EIA422 SiteScan Web LED IndicatorsLED indicators summary LEDs EIA422Typical Sequence Packing Contents Installation ConsiderationsInstallation Unpacking and Preliminary InspectionMounting the Panel Surface-Mounting the AC8Required tools 304.8mm 213 4mmFlush-Mounting the AC8 Termination and Mounting Connect Power to the AC8Input Power Connections TM115 TM230 Connection TypeConnecting the Battery Pack VAC Output Power ConnectionsTroubleshooting Transformer Module Obtaining a Replacement Battery PackWiring specifications Wiring SpecificationsWiring and Connections Connecting Digital Inputs Connecting Digital Inputs and Digital OutputsConnecting Liebert Environmental Units Setting the Digital Output Jumpers Digital output jumper settingsSetting the Epop Jumper Connecting Control Relay OutputsConnecting the Emergency Power Operation Epop Input Connecting the Analog Ground Connecting Analog InputsSetting the 12VDC/24VDC Analog Power Jumper 1 RS232 Connector Connecting Common Alarm OutputsEIA422 SiteScan Web Connector Phone Line ConnectorOverview of Menus Guide to AC8 functionsLCD Menu Overview Opening Screen OverviewMain Menu Overview View Status Options Clearing Active Alarms View Active AlarmsActive Alarms Active AlarmsAlarm log conditions Main Menu View Alarm LogAlarm Log Alarm LogEvent Log View Event LogEvent Log Event log conditionsView a Trend Log View Trend LogSelect a Sensor Viewing Additional Input Data View Input StatusInput Status Viewing Additional Output Data View Output StatusOutput Status Digital output statesView a Pager Number View Pager NumbersSelect a Pager View a Pager PINView Operation View OperationSelect a Zone Zone SelectionControl Status View Control StatusControl Status View Control StatusSilence Alarm & Backup LOG Files Service Terminal Interface Silence Alarm Service Terminal Interface onlyBack Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface System and Control Options LoginLogin Valid characters for data entrySystem & Control menu Clear Alarms&Logs selected Login ScreenSystem & Control menu Setup System selected Setup System menuSetup System Overview Setup System Setup InputsDefine Input as Normally Open or Normally Closed Define Input as Alarmable or EventChange Label Name of Input Delay Time Set Up Alarmable Inputs in Latched or Unlatched ModeSet Up Delay Time Latched / UnlatchedReset Common Alarm Setup System Setup Common AlarmChange to Reset Y or Not Reset N Setup Common AlarmDefault settings analog sensor inputs Setup System Setup SensorSelect a Sensor to Configure Setup SensorChange Units Label Identify the Sensor as ConnectedChange Sensor Label Name Change Offset Value Change 4 mA ValueChange 20 mA Value Message if sensor has been defined as an event Define Sensor as Alarmable or EventSet Up Alarmable Sensors in Latched or Unlatched Mode Latched NChange Low Setpoint Change Low SetpointChange High Setpoint Change High SetpointSensor Delay Total devices Setup System Setup ZonesSet Up a Zone Previous zone has no devicesSetup System Setup Outputs Define Output as Normally Open or Normally ClosedConfigure Output for Loss of Power Fail-Safe Define Operating or Standby ModeEnable or Disable an Output Device in Alarm Status Supported Modem Settings Setup System Setup Modem & PagersModem Setup Initialization String Default Modem SettingsEdit the Init String International DialingCountry codes Country CodeEnter AC8 Phone Number Change Modem Dial Prefix Enable Modem Diagnostic MessagesChange Modem Hang Up Delay After a Call Pager dialing results Pager Setup Pager Number and PINSelect a Pager to Configure Select Pager MenuGuidelines for dialing pagers Setup Pager MenuEnter a Pager Number Enter a Pager PIN NumberEnter Pager NUMBER40 Characters MAX Command Successful Enable Communications Check Enter Time To Perform Communications CheckSetup System Info Setup Operation Setup I/O Matrix Setup System Setup System InfoSelect Setup System Reset Password to the Factory Default Aaaa Change PasswordChange the Password Change Date & Time/Automatic Daylight Saving TimeSetup Site ID Setup Site IDConnect Battery Battery alarmsBackup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Guidelines for dialing service phone number Setup Serv Ph Num Enter Phone NumberService phone number dialing results Setup Serv Ph NumSetup Service Phone Number Service Terminal Interface only Firmware Update Service Terminal Interface only Factory DefaultsFactory Defaults Factory DefaultsSystem and Control Options Initiate Remote Alarm Test Service Terminal Interface only DisconnectSetup Operation Turn Automatic Sequencing On or Off Specify Failed Standby Response Turn Standby Testing On or OffChange Standby Testing Failed Standby responseRestart Delay Time Specify Hold Delay TimeHold Delay Time Specify Restart TimeSpecify Staging If sensor for zone is not connected to AC8Default Mappings Digital Inputs to Control Relays Setup System Setup I/O MatrixSet Up Mapping for a Digital Input Map Sensor to Control Relay Set Up Mapping for an Analog Sensor InputDefault Mappings Analog Inputs to Control Relays Override Output Clear the Alarm Log Clear Alarms & LogsClear Active Alarms Clear Event Log Clear the Event LogClear the Trend Logs Clear Trend LogAC8 Specifications SpecificationsAppendix a Service Terminal Interface Comparison of Functions LCD and Service Terminal InterfaceConnection Methods Connecting to the Service Terminal InterfaceSteps to set up a direct or remote connection Create a ConnectionDirect Connection via RS232 Remote Connection via Modem Set Up the COM1 Port Direct Connection OnlyCOM1 Port Setup Choose COM1 Choose the computer’s modem Proceed to StepAscii Setup Set Up the Connection’s PropertiesProperties Setup Settings tabDial button OK button Connect to the Service Terminal InterfaceClick on the file name for example, AC8.ht View Status Overview Silence Alarm and Backup Log FilesSetup Menu Overview Main Menu For sample screens, seeView Status Menus View Active AlarmsView Active Alarms Main MenuView Alarm Log View Alarm LogView Event Log View Event LogView Trend Log View Trend LogView Input & Sensor Status View Input StatusView Output Status View Output StatusView Pager Numbers View Pager NumbersView Control Status View Control StatusView Operation Silence Alarm Section A.5.1 Section A.5.2Backup Log Files Event Log File Back Up Alarm Log FileBackup Log Files Alarm Log File Back Up Event Log FileBackup Log Files Trend Log Files Back Up Trend Log FilesLogin Setup MenuLogin Menu Tips on Using the Service Terminal Interface Setup MenuSetup Menu See DescriptionSetup Inputs Setup InputsSetup Common Alarm Setup Common AlarmSetup Sensor Setup SensorSetup Zones Setup ZonesSetup Output Setup OutputsSetup Modem & Pagers Pager Setup Setup Modem & PagersPager Setup Modem Setup Setup Modem & Pagers Modem SetupChange Password Setup System InfoSetup System Info Set Date & Time/Automatic Daylight Saving Time Setup Site IDConnect Battery Set Date & TimeBackup & Upload Configuration File Backup Backup & Upload Configuration File UploadFactory Defaults Setup Service Phone NumberSetup Service Phone Number Firmware Update Initiate Remote Alarm TestAuto Sequencing Setup OperationSetup Operation Auto Sequencing Standby Testing Setup Operation Standby TestingSetup Operation Failed Standby Failed StandbyHold Delay Setup Operation Hold DelayRestart Delay Setup Operation Restart DelaySetup Operation Staging StagingOverride Output Override OutputClear Alarms & Logs Clear the Alarm Log Clear Alarms & LogsClear Alarms & Logs Clear Active Alarms Clear Alarms & Logs Clear the Event Log Clear Alarms & Logs Clear the Trend LogsSetup I-O Matrix Map Sensor to Control Relay Setup I/O MatrixSetup I-O Matrix Map Input to Control Relay Digital input Mapping to control relay Appendix B Default Settings Quick Reference GuideAC8 default settings for inputs and outputs Analog input Mapping to control relayAC8 other default settings Default Settings Modem from Table Feature Other OptionsPage Locations Technical Support/ServiceCompany Behind the Products United States