WAN Status | Epson 3300 guide

WAN Status

The status of WAN interface (Static, DHCP, PPPoE, PPTP or DMZ) is shown in this page. Simply click WAN Status tag to get the detailed. There are four sets of WAN status can be shown in this page at one time. The sample below just lists one set of WAN status for only WAN1 interface is used.

IP Address	Displays the IP address of the WAN interface.
MAC Address	Displays the MAC address of the WAN Interface.
Primary DNS	Displays the IP address of the primary DNS.
Secondary DNS	Displays the IP address of the secondary DNS.
Gateway	Displays the IP address of the default gateway.
RX Packets	Displays the total received packets for each WAN interface.
TX Packets	Displays the total transmitted packets for each WAN interface.
Connection Status	Displays the connection status of the WAN interface.
Up Time	Displays the total system uptime of the interface.

Vigor3300 Series User’s Guide

25

Image 29

Epson 3300 manual WAN Status

Contents

Vigor 3300 Series Declarations Copyright Information Table of Contents Appendix a Application for 802.1 Vlan 137 Trouble Shooting 127 Preface Factory Reset LED Indicators and ConnectionLED Indicators and Connectors for Vigor3300V Interface Description WAN LED Indicators and Connectors for Vigor3300 WAN/DMZ WAN1 ~ WAN3 LED Indicators and Connectors for Vigor3300B+ Auxiliary Type Connected to Remarks Cables Color Connecter Specification Hardware Installation RS232 Connector Detailed Explanation for the ConnectorStandard 10/100 Base-T Ethernet Interface Connector Chassis Connections Desktop Type Installation Changing Password Configuring Basic Settings Vigor3300 Series User’s Guide Adjusting WAN Connection Mode Quick Setup Physical Mode Static Mode End IP StatusStart IP Dhcp Mode PPPoE Default value is PAPUse for clients in LAN Primary DNS Type the IP address for primary DNS Primary DNS Pptp IP Address Status, and WAN Status System setupStatus LAN Status Basic Status TX Packets High Available StatusRX Packets WAN Status Time Syslog Server Port SyslogSyslog Server IP Access Control Push Backup Button File name is v3300.cfg Configuration Setup Firmware Upgrade from a Console Port Firmware Upgrade Setup Tftp -i 192.168.1.1 PUT Vigor3300 image file name Vigor3300 Series User’s Guide Reboot Destination Diagnostic ToolsFlag s Interface Time Left Assigned IP Vigor3300 Series User’s Guide WAN and Internet Access Setup Network SetupBackup Load Balance Default Route IP ModeWeight Backup-Master Static IP Setup Host Name ResetDomain Name Detect Type Request supported in the router Dhcp Client Setup Service Name PPPoE with a DSL Modem SetupUser Name Detect Interval Pptp Local Address Pptp with a DSL Modem SetupPptp Subnet Mask Pptp Remote Address For LAN IP/DHCP 2 LAN WAN Interface For Dhcp Relay Agent LAN Interface For IP Routing Protocol Load Balance PolicyDest Port Start Dest Port End Delete/Delete All High AvailabilitySource IP/Subnet Mask Dest IP/Subnet Mask Vigor3300 Series User’s Guide High Availability Static DhcpGroup Number Role Advanced Setup Edit the Static Route Static Route Setup Destination IP Delete the Static RouteLAN , and WAN1~WAN4 Port Redirection NAT Setup Comment Private Port Range Public Port RangeUse IP Alias IP Alias Address Mapping DMZ Host Display the WAN interface chosen for this entry Configured in Network WAN interface Radius SetupCommon Ports List Alias addresses Server IP Address Enable/DisableDestination Port Shared Secret Port Block Ddns SetupIndex Port Number Interface should be any WAN port on V3300 series Login Password Login NameBackup MX Server Provider Edit Call Schedule Call Schedule Setup Select some weekdays to apply Delete Call ScheduleUp means to activate the Network Interface Mirrored Ports WAN Port Mirroring SetupMirroring Port LAN Vlan Setup LAN Port Mirroring Setup Vlan 0 For Port Base VlanP1 P4 Member For 802.1Q VlanName Port Valn ID SnmpFrame Tag Operation Snmp Community Max AccessCommunity Host/mask Vigor3300 Series User’s Guide Trap Server Snmp TrapsTrap Community Trap server port Vigor3300 Series User’s Guide IP Filter Firewall SetupGeneral Setup Group Table Delete Source Port Destination Mask End PortDirection Fragments Further match or Pass if no further match of Block or Pass 2 DoS Enable Icmp Flood Value is DisableDoS Defense Defense URL Filter SurfControl, Restrict Web Feature and Filter Schedule URL Access Control SurfControl Restrict Web Feature Filter Schedule Block only at Quality of Service SetupAlways Block Vigor3300 Series User’s Guide Disable/Enable Incoming/Outgoing Class SetupIncoming/Outgoing Class Filter Class Name Class Service Type StatusPriority DiffServ CodePoint Status PortBasic Only the DiffServ CodePoint Type field can be Advanced Only the DiffServ CodePoint field can be VPN and Remote Access Setup IPSec ConfigurationPolicy Table Delete All Profile Status For Default Configuration Security Protocol For Advanced ConfigurationLocal Certificate Security Gateway Vigor3300 Series User’s Guide Timeout Delay Date/Time LogTrust CA Generate User CertificateDownload Import Domain Name Certificated by domain name Certification Name Name of the certification entry ID TypeIP Certificated by IP address Email Certificated by email address 102 Status Pptp Encryption Pptp AuthenticationUser Authentication User Password Authentication192.168.1.224/28 Group Type username, password and choose proper group for this Protocol VoIP Setup For SIP Configuration For Mgcp Configuration For Phone Number Port Settings Hotline Port 1 FXS FXO Codec VAD Enable or Disable VAD Voice Activity For Group Dtmf ModeCall Forwarding Call forwarding no answer after Range 1~10 rings Speed Dial Prefix Advanced Speed DialStrip Length Append Starting Port MiscellaneousRedundancy Number Dialing Completion Tone Settings Caller ID Type Region 7 QoS EnableLink Fragmentation Interleaving NAT Traversal Semi-auto, need to config NAT If you click this functionManually Input NAT IP Address Set Incoming Call Barring Deny List Allow List Call History Remote RTP Port Remote RTP AddressRTP Statistic Codec Type 125 126 Checking If the Hardware Status Is OK or Not Trouble Shooting For Windows 129 For MacOs For MacOs Terminal Pinging the Router from Your Computer For PPPoE Mode Checking If the ISP Settings Are OK or Not For Static Mode For Dhcp Mode Software Reset Backing to Factory Default Setting If NecessaryFor Pptp Mode Contacting Your Dealer Hardware Reset Block LAN-to-LAN Communication Appendix a Application for 802.1 Vlan How to Check/Edit Vlan ID on Your PC? 139 140 141 142 143 144 Four VLANs for Different Departments in a Company ProcedureApplications 146 Two VLANs for Different Departments in a Company 148 Example for the Companies in the Same Building 150 Example for a Company and Guest 152 Example for Trunk Usage 154