Clone Remote in Multipoint Configurations | Paradyne 3910 specification

COMSPHERE 3900 Series Modems

Viewing DC Broadcast Clone Results

Choose DLL Type >

DC_CloneResults

F1 F2 F3

From the Choose DLL Type screen, press the key until DC_CloneResults appears to view the results of the last DC_Broadcast clone operation. If the message Trib List Empty appears, this indicates that a multiple download was never initiated.

DC Clone Results

Nxt xxx Pass

F1 F2 F3

The address field (xxx) displays the network management address of one of the remote modems. Pressing the F1 key allows you to select various remote modems to determine the download result for those modems (Pass or Fail).

Clone Remote in Multipoint Configurations

A Trellis Multipoint (TMp) control modem can be used to download firmware to just one tributary modem (Single) or to all of its tributary modems (Multiple).

NOTE

A Trellis Multipoint (TMp) tributary modem cannot download firmware to its control modem. To download firmware to a TMp control modem use a point-to-point dial connection, an NMS, or a PC controller.

Before using Clone Remote in multipoint configurations (Single or Multiple), perform the following:

•Make sure the 391x Series modems have an established leased-line connection using the Trellis Multipoint (TMp) modulation (refer to the Leased Line section in Chapter 4).

•Make sure the remote modem's Access From Remote configuration option is enabled (refer to the Misc section in Chapter 4).

•For Single download configurations, know the remote access password and the network management address of the remote tributary modem that will receive the download. Refer to the Misc section in Chapter 4 for a description of the remote access password (RemAccssPasswrd) configuration option and the network management address (NetMngmtAddress) configuration option.

3-38

November 1996

3910-A2-GN32-30

Image 72

Paradyne 3910 operation manual Clone Remote in Multipoint Configurations, DC Clone Results Nxt xxx Pass

Contents

Document No -A2-GN32-30 Warranty, Sales, and Service Information TrademarksCopyright E 1996 Paradyne Corporation. All rights reserved Important Safety Instructions CC DGD D C D CC Table of Contents DCP Configuration Glossary Index List of Figures Optional SDCP, Model 3911 Faceplate, and Optional SDU List of Tables Comsphere 3900 Series Modems How to Use this Manual PrefaceObjectives and Reader Assumptions Related Documents Features IntroductionOverview Leased Backup Applications Multipoint ApplicationsComsphere 391x Series Models Standalone Model 3910 4-Wire/2-Wire Modem Carrier-Mounted Model 3911 4-Wire/2-Wire Modem 3911 Government Requirements and Equipment Return United States Comsphere 3900 Series Modems Canada Technical Specifications Technical Specifications for 391x Series Modems DescriptionModel Certification Number See label on modem Leased-Line Modulations Technical Specifications for 391x Series Modems Specifications DescriptionPin D-subminiature connector EIA-232-D/CCITT 100 to 250 Vac, 50 to 60 Hz MNP Ccitt V.42bisMNP Class Modem Installation 391x Series Modem Package Model 3910 Modem Installation Customer-Supplied Equipment Connecting Cables to the Model 3910 Modems Model 3910 Rear Panel and Power Supply Model 3910 4-Wire/2-Wire Leased-Line Connection Model 3910 Dial Backup ConnectionModel 3910 Leased Backup Connection DTE Connection Power Supply Connection Modem Power-UpPower On Selftst Passed Network Management System Connection Selecting Factory Configuration Options Using the Diagnostic Control Panel DCP Using AT Commands Type AT Type AT&Fy&Wn Model 3911 Modem Installation Removing and Replacing Model 3910 Modems Installing a Model 3911 Modem Circuit Pack Lock Removing and Replacing Model 3911 Modems DCP Operation Top-Level Menu Status and Operational Messages Diagnostic Control Panels Model 3910 Diagnostic Control Panel Model 3910 DCP Status Indicators Optional SDCP, Model 3911 Faceplate, and Optional SDU Model 3910 and Model 3911 DCP LEDs Label Color Indicates PwrAlrm Diag Diagnostic Control Panel Operation LCD Display Keypad Menu Structure Call Setup Top-Level Menu Status and Operational MessagesTop-Level Menu Status Status Message Indicates Normal Status Message Indicates Dial Backup or Standby MR Modem is operating in Dial Standby modeLeased Backup Call Failure Status Message Indicates Call Failure ContCall Disconnect Firmware AT Command ResetStatus Message Indicates Firmware Result Cont Dial Access Security Messages Dial Access Security Indicates Message Quick Configuration Display Leased19.2 Status ConfigureLeased19.2 abbb cdd ee ffff Status Branch Status Device Health and Status DeviceHS Status DeviceHS VFDevice HS Major Minor Health and Status Messages Type Message Indicates MajorMinor Status Type Message Indicates Dial ThreshSecurity Port SigQual RcvLevelSig/Noise NrEchLvl Identity Backup Status Identity DTELSD DTR DSR Tst Backup StatusBackup Line=Pri 4w APLStatusBackup Bkup2wAPL=Good Status Backup Status Screens Possible Inactive/Backup Line ConditionOptions Active Line Record OptionsStatus 29V.33Status Options Record Record Status Display Clear Configure Branch Poll List Branch Display Leased19.2 PList ControlPoll List Display Clear Clear function does not appear in Remote mode ClearChange Change function does not appear in Remote Add Poll ListChang Active DeletePoll Listyyyyyy Ent Poll List Change Add Poll ListAdd Command Complete Acquire function does not appear in Remote modeAcquire Poll List Add Acquire Control Branch Poll ListAcquir Num Acquired yyyLeased19.2 Control Test Reset Control Speaker ResetSpeaker Speaker Control Off Low Med Data Stream function is not available in Async mode Data Stream Port1 DisableData Stream Port1 Enable Data Stream Eialed Command Complete EIA LEDsControl EIALEDs Eialed Port1CC Make Busy Command Complete Make Busy/Remove Make BusyControl MakeBusy Control RemoveMakeBusy Service Line/Disconnect Service Line Control ServiceLineDownload Software Control DownloadCode DwnLoadSoftware CloneRemote Choose DLL Type SCClone Cloning DC Broadcast RemoteChoose DLL Type DCBroadcast Clone Remote in Multipoint Configurations DC Clone Results Nxt xxx Pass Choose Password Ent yyyyyyyy Cloning a Single TMp Remote Choose DLL Type Single MultipleChoose Address Ent Implementing a Clone Remote Operation MPtCloneResults Nxt xxx Pass Access Disabled Password InvalidIncompat Modulat No Response VF Thresholds Update Control VFThreshUpdateVF Thresholds Edit Save Reset RemClone Status Bank1xxxx/yyyy RSL High dBm Nxt Refer to -8 for valid VF threshold rangesIf you want to modify additional VF thresholds, select Nxt Save VF Thresh Thd Out of Range Valid Ranges for VF Thresholds Default Values Test Branch Abort TestAbort Command Complete SelfTest Abort Self Loc Analog Loop Test LocAnalogLoop Rem Digital Loop TestLocal Loop Started Loc Digital Loop Test RemDigitalLoopTestRemote Loop Started Pattern Test LocDigitalLoopTestDigitl Loop Started Test Pattern TestPattern BlksErrd=xxxxxxx Sub-Network Health and Status Branch Leased19.2 TestSubHS Call Setup Branch Call Setup function is not available in TMp Control modeSub-network HS Nxt Xxx Yyyyyy Leased19.2 CallSetup Call Setup Dial DisconnectDial Disconnect Command Complete DisconnectDialDirectory Nxt DialDirectory01 Off Hook Call Setup Answer Answer Command CompleteAnswer Dial Standby/Return to Dial Call Setup Dial Standby Call Setup ReturntoDial Dial Standby Command Complete Call Setup ChangeDirectoryChange Directory 01 551234 z Nxt 02z Nxt 019W5556789z Nxt Valid Dial Command Modifiers Call Setup DirectoryStatusDirectory Status Does Not Appear in North America Talk/Data function is not available in TMp Control mode Talk/Data BranchNumber Status Nxt 01Allowed Online19.2 CallSetup Idle19.2 Tlk/Data Security Branch Remote Branch Leased19.2 Security Remote Multipoint tributary modems Select Channel Secondary Prim Data blckd Online14.4 Control ExitRem Status ªStatusº Diagnostic Control Panel Access Frnt Panl Acces GrantDeny DCP Configuration DCP Configuration Process AT Command Configuration Process Choose Function Editing and Saving a Configuration Option LdEditAreafrm ActivOperatingLdEditAreafrm Factory Ld Fact Preset SyncLeased Choose Mode Answer OriginateChoose Function EditSave Edit StrapGroup DTEInterface StrapsWhenDisc Nxt NoChange RemAccssPasswrd Nxt Summary Choose Function Edit SaveSav EditArea to ActiveSaved Configuration Tables DTE Interface DTE Interface Configuration Options Asyn Parity Bit None Nxt None Even Odd Mark Space DTE Interface Configuration Options DTE Interface Configuration Options DTE Interface Configuration Options DTE Interface Configuration Options DTE Interface Configuration Options TX Clock Source Internal Nxt Internal External RXCLoop Fallback2 Not available for TMp tributaries Extend Main Ch. Disable Nxt Disable Enable DTE DialerPrimary data can only be extended one link DTE Dialer Configuration Options AT Escape Char 043 Asci Nxt 043 Asci CarriageRtn Char 013 Asci Nxt 013 Asci DTE Dialer Configuration Options AT Cmnd Mode Normal Nxt Normal NoERROR NoStrapOrERR Line Dialer Configuration Options Line Dialer Blind Dial Pause 2sec Nxt 2sec 4sec 6sec 8sec 10sec 20sec Line Dialer Configuration Options Line Dialer Configuration Options Line Dialer Configuration Options Dial Line Configuration Options Dial Line V32bis Automode Enable Nxt Enable Disable System V22b Guard Tone Disable Nxt Disable 550Hz 1800Hz Leased Line Configuration Options Leased Line Leased Line Configuration Options V32bis Autorate Enable Nxt Enable Disable Leased Line Configuration Options Leased Line Configuration Options DualLeasedLn Disable Nxt Disable Enable 42/MNP/Buffer 42/MNP/Buffer Configuration Options 42/MNP/Buffer Configuration Options EC Negotiat Bfr Disable Nxt Disable Enable Disab&Switch Flw Cntl of DTE CTStoDTE Nxt CTStoDTE Disable XON/XOFF XON/XOFF XON/XOFF Psthru Disable Nxt Disable Enable Break Buffr Ctl KeepData Nxt KeepData DiscardData BuffrDiscDelay 10sec Nxt 10sec Disable 60sec RdcdAsyncBufSiz Disable End Disable Enable Test Configuration OptionsTest Test Configuration Options Miscellaneous Configuration Options Misc Miscellaneous Configuration Options Miscellaneous Configuration Options Diag Connection ModemDC Nxt ModemDC Nmscc Disable Security AT Command Set and S-Registers Switching Between Data Mode and Online Command ModeOperating Modes Command Guidelines Escape Sequence and Escape Guard Time Result Codes Result CodesNumbers Word Description AT Command List AT Command FormatResult Codes Numbers Word Description 391x Series AT Commands Description CommandATD9W5551234 DCP LCD Sn=r Dial Tone DetectBusy Tone Only displays OK, CONNECT, RING, no Carrier DCP LCD DCP LCD Bert \A3 \C0 \D0 \G0\N5 42bis Compression Configure\Edit\ Disable V42/MNP/BufferRegister List \X0 Register Format 391x Series S-Registers Description DCP LCD DCP LCD DCP LCD DCP LCD DCP LCD = Ascii = Ebcdic DCP LCD DCP LCD DCP LCD DCP LCD DCP LCD DCP LCD Dial Access Security Menu Tree a Status ªStatusº Control SubHS CallSetup Tlk/Data Troubleshooting B Symptom ActionTable B-1 Modem Health Must be configured for 4-wire operation Dial Backup OperationTable B-2 Leased-Line Operation Table B-4 Modem Ð DTE Connection Modem Ð VF Connection Dial Table B-5 Modem Ð VF Connection Symptom Action Table B-6Online Operation Pin Assignments C Signal Circuit Function Source EIA-232-D Pin AssignmentsTable C-1 EIA-232-D Pin Assignments Name VF Connector Pin Assignments Table C-2 VF Connector Pin Assignments Type of Telco JackLeased Dial RJ11 Pin Auxiliary Cables Not Supplied Position Plug PIN no Figure C-4. Wiring Diagram Ð 25-Pin Crossover Cable Ccitt V.25bis Dialing Commands D and Responses Call Request Commands Call ResponseCall Request with Number Provided CRN Call Request with Stored Memory Address Provided CRS Call Answer Commands Call Connecting CNXDelayed Call Indicator Incoming Call INC Request List of Delayed Numbers RLD Program Normal PRNRequest List of Forbidden Numbers RLF Connect Incoming Call CIC List Delayed Numbers Response LSD Request List of Stored Numbers RLNList Forbidden Numbers Response LSF List Stored Numbers Response LSN Command Response Valid VALInvalid INV Call Answer Commands Program CommandList Request List Response Call Connecting Indication Command ResponseValid Command Call Failure Indication Ascii Character Table E Table E-1 Ascii Characters Hexadecimal Decimal Control KeyCharacter 023 024025 026 Ascii Character Table Table E-1 Ascii Characters Hexadecimal Decimal Control Key Default Configuration Options F Table F-1 Factory Default Configuration Options DTE Interface DTE Dialer Line Dialer Leased Line Default Misc Entry Wait Time VF Prompt Type Sample Configuration G Configuration Options Point-to-PointCables Figure G-2. Sample Configuration Ð Multipoint Multipoint Point-to-Point with Automatic Dial Backup Auto Dial Back Set to Enable Point-to-Point with Network Management Carrier with Network Management Figure G-6. Sample Configuration Ð Extended Multipoint Extended Multipoint Rate at 19.2K Set ports 1, 2, 3, and 4 to Extended Diagnostics Adapter 3910 E,G871A Equipment Feature Part Number Equipment List H Glossary Automatic dial backup Automatic dial standbyAutomatic rate control Backbone network Command mode Configuration areaConfiguration option Connector Constant carrier mode Controlled carrier modeData mode DB-25 connector Dial command modifiers Digital signalError control Dial line Forward Error Extended networkExtended result codes Fallback Leased line LinkLocal analog loopback Long space disconnect Originate mode Phase jitterPower-up self-test Quick Configuration Register Remote loopbackResult code Return to Dial Time Division Multiplexer TDMTMp Top-Level menu Index Index-2 DTE Index-4 Index-5 Index-6 Index-7