CM9760-VMC Video Output Card Installation Slot | Pelco System 9760

4.Install the new card into slot 17 of the matrix bay as follows (refer to Figure 30):

a.Align the top and bottom edges of the card with the top and bottom card guides of the matrix bay.

b.Slide the card toward the rear of the matrix bay until the card is seated ﬁrmly with the connectors on the backplane and with the associated rear panel card connector. If the audible alarm on the power supply is enabled, the alarm stops beeping and the Frame Fault LED turns off.

c.To ensure proper operation of the CM9760-VMC card, reset the card by pressing the Reset button on the card.

For about ﬁve seconds, the audible alarm on the power supply beeps and the Frame Fault LED ﬂashes red. The LEDs on the video output card then indicate proper operation.

5.Reattach the front panel of the matrix bay.

CARD GUIDE

VIDEO OUTPUT CARD (SLOT 17)

CARD HANDLE

FRAME

FAULT

LED

LEDs

RESET

BUTTON

CARD

HANDLE

CARD

GUIDE

Figure 30. CM9760-VMC Video Output Card Installation (Slot 17)

C1572M (9/05)

51

Image 51

Pelco System 9760 manual CM9760-VMC Video Output Card Installation Slot

Contents

System Page Contents Testport Directory DOS Directory C1572M 9/05 List of Illustrations List of Tables Important Safety Instructions Regulatory Notices CM9700-CC1CM9760-MXB Description System Overview Keyboards ModelsCPU Controller and Components Matrix BAY and Components Network Interface Unit Optional ComponentsCompatible Receivers System Setup Overview System Setup Unpacking Unpacking the CM9700-CC1Unpacking the CM9760-MXB Installing the CM9700-CC1 Controller Selecting a Location for the CM9700-CC1Mounting the CM9700-CC1 Unit Connecting the CM9700-MGR PC to the CM9700-CC1 Connecting the CM9700-CC1 Connecting a PS/2 Keyboard to the CM9700-CC1 Connecting a VGA Monitor to the CM9700-CC1 System 9760 Factory Default Port Settings Connected through the hot switch Other devices CM9760-HS Port CM9760-MXBsSequential ports Interface unit Matrix bays Connecting Power to the CM9700-CC1CM9760-HS Port CM9700-NW1 Matrix bays Installing CM9760-MXB Matrix Bays Powering on the CM9700-CC1Selecting a Location for the CM9760-MXB Mounting the CM9760-MXB Sample Downframe Cable Connections Verifying CM9760-MXB Component Installation CM9760-MXB Front Panel Removing the CM9760-MXB Front Panel CM9760-MXB to CM9700-CC1 Connection Connecting the CM9760-MXB to the CM9700-CC1 Connecting Power to the CM9760-MXB Powering on the CM9760-MXBChecking Diagnostic Leds CM9760-VCC and CM9760-VMC Diagnostic LEDs Fuse Locations on CM9760-VCC and CM9760-VMC Cards 241 Connecting Video Inputs and Video Outputs Enter Monitor # Verifying System Operation Removing the CM9700-CC1 TOP Cover CM9700-CC1 Component Installation or Replacement Installing or Replacing a CM9700-SER Card No jumpers ISA Slot Number W1 IRQ Setting W2 Address SettingIRQ Pins 1 to 2 and 3 to Pins 1 to 2 only Pins 3 to 4 only Installing a CM9760-RPC Card CM9760-MXB Component Installation or ReplacementInstalling or Replacing Rear Panel Cards Installing or Replacing a CM9760-RPC Rear Panel Input Card Termination Jumpers on CM9760-RPC Rear Panel Input Card Replacing a CM9760-RPC Card Installing a CM9760-RPL Card Installing or Replacing a CM9760-RPL Rear Panel Looping Card Replacing a CM9760-RPL Card Installing a CM9760-DFC Card Installing or Replacing a CM9760-DFC Downframe Card Replacing a CM9760-DFC Card Installing a CM9760-DFL Card Installing or Replacing a CM9760-DFL Downframe Looping Card Replacing a CM9760-DFL Card Installing a CM9760-RPM Card Installing or Replacing a CM9760-RPM Rear Panel Output Card Replacing a CM9760-RPM Card Installing or Replacing a CM9760-VCC Video Input Card Installing a CM9760-VCC CardSlot Physical CM9760-VCC Video Input Card Installation Slots Replacing a CM9760-VCC Card Installing a CM9760-VMC Card Installing or Replacing a CM9760-VMC Video Output Card JP2 X55 Function Switch CM9760-VMC Video Output Card Installation Slot Replacing a CM9760-VMC Card Installing a CM9760-VMM Video Output Module Installing a Backup Power Supply Installing or Replacing a Power Supply Replacing a Power Supply CM9760-MXB Power Supply Fuse Replacement Replacing a Power Supply Fuse ENABLING/DISABLING the Power Supply Alarm Performing System 9760 DOS Programming Tasks System Programming Using DOS Setting System Time in a Single-Node System Setting and Adjusting System Time in a SINGLE-NODE System Adjusting System Time in a Single-Node System 14 000230.00 0228.0 Making Additional Adjustments to System Time CM9700 NODEx /Tmmsshh where Setting System Time in a Multi-Node System Setting and Adjusting System Time in a MULTI-NODE System Adjusting System Time in a Multi-Node System C1572M 9/05 Making Additional Adjustments to System Time Editing the Net.bat File to Permanently Adjust System Time DOS Filename Conventions DOS Command Reference File and Disk Management Commands DEL Command† Switch†† Description Examples§¶ Brieﬂy describes Speciﬁed command About the DIR commandType command When viewing a long Text ﬁle. When More Redirection operator Symbol is used. Monitoring CM9700-CC1 Functions System Diagnostics Viewing Monitor BOX Diagnostics Allocating Monitors to Monitor Boxes System Box Display Message Entering CM9700-CC1 PC Keyboard Commands Alt+S System on Updated Demo OffAlt+T Resynch Trap Ofﬂine Resynch Trap Online Alt+D Demo On Viewing MULTI-NODE System Status Sample CM9700-NW1 Diagnostic Screen Entering CM9700-NW1 PC Keyboard Commands Hardware Error Possible Cause Corrective Action TroubleshootingGeneral Troubleshooting Guidelines Troubleshooting the CM9700-CC1 System Error Message Possible Cause Corrective Action LED Color Possible Cause Corrective Action Troubleshooting the CM9760-MXB CM9700-CC1 Controller Illustrates the front of the CM9700-CC1 Front View Illustrates the rear of the CM9700-CC1 Rear View CM9700-CC1 Rear Connector Pinouts DOS DIR Directory Structure Directory NODEx.GPI GPI setup ﬁle DOS Directory Testport Directory Functional System Overview CM9760-MXB Matrix Bay Video Signal Flow through the Matrix Bay Illustrates the CM9760-MXB with the front panel removed Not Used CM9760-MXB Alarm Port Following guidelines apply to the CM9760-VCC card Video Input and Output CardsCM9760-VCC Video Input Card CM9760-VCC Card Guidelines CM9760-VMC Video Output Card Rear Panel Cards CM9760-RPC Rear Panel Input CardCM9760-VMC Card Guidelines CM9760-RPC Card Guidelines CM9760-RPL Rear Panel Looping Card Terminated Unterminated OUT BNC Pairs CM9760-RPL Card Guidelines CM9760-RPM Rear Panel Output Card CM9760-RPM Card GuidelinesFollowing guidelines apply to the CM9760-RPM card CM9760-DFC Rear Panel Downframe Card CM9760-DFC Card GuidelinesFollowing guidelines apply to the CM9760-DFC card CM9760-DFL Rear Panel Downframe Looping Card CM9760-DFL Card Guidelines Power Supplies Sideframing and Downframing 481 257 241 Sideframing 104 C1572M 9/05 241 Downframing 106 C1572M 9/05 481 257 241 Using a Combination of Sideframing and Downframing 256 Downframing to the CM9760-MXBL241 Cams CM9700-CC1 Specifications CM9760-MXB SpecificationsSpeciﬁcations Connecting AN ACD DB9 Port to a CM9700-CC1 DB9 Port Appendix A. CM9700-CC1 Ascii Protocol CommunicationACD to CM9700-CC1 Connections PV140 Connecting AN ACD DB9 Port to a CM9700-CC1 RJ-45 Port Ascii Protocol Commands Supported by the CM9700-CC1 Action Command Table O. Ascii Command Summary Lock Next Camera Previous Camera Select Monitor 9999Ma Lock Camera to Monitor~Ga Select Camera 999999#a Action Command Command Description Pan and Tilt Commands Action Command Command Description Action Command Command Description Advanced Commands Matrix Control Commands Then again in a 4X magniﬁcation Digital Zoom ym commandSelect Multiplexer Input command for each input Digital Zoom 47Ra33Da Table Q. Ascii Command Examples C1572M 9/05 121 Illustrate sideframe-only conﬁgurations SIDEFRAME-ONLY Configuration Examples To illustrate downframe-only conﬁgurations DOWNFRAME-ONLY Configuration Examples Downframing 256 x 48 Conﬁguration, Looping Downframing 256 x 64 Conﬁguration Downframing 256 x 64 Conﬁguration, Looping Sideframe and Downframe Combination Configuration Examples 257-496 256257-496 481 257 241 Sideframing and Downframing 496 x 48 Conﬁguration, Looping Sideframing and Downframing 496 x 64 Conﬁguration Sideframing and Downframing 496 x 64 Conﬁguration, Looping 513 497 257 241 721 513 497 257 241 721 Sideframing and Downframing 736 x 48 Conﬁguration Sideframing and Downframing 736 x 48 Conﬁguration, Looping 497 257 241 22D Sideframing and Downframing 736 x 64 Conﬁguration, Looping 769 753 513 497 257 241 961 257 241 961 769 753 513 961 769 753 513 497 257 241 C1572M 9/05 141 961 769 753 513 497 257 241 Sideframing and Downframing 976 x 64 Conﬁguration, Looping 257-512 256 CM9760-MXBL Downframe Configuration Examples 721 513 497 257 241 Downframing to CM9760-MXBL 976 x 16 Conﬁguration, Looping Product Warranty and Return Information ISO9001