Powerware 650825 kVA operation manual Common Battery

UPS INSTALLATION PLAN AND UNPACKING

For external wiring requirements, including the minimum AWG size of external wiring, see Table 3-4for installations using a common battery system, Table 3-5for installations using a separate battery system, or Table 3-6for separate rectifier feed installations. Wire sizes listed are for copper wiring only.

Table 3-4. Input/Output Ratings and External Wiring Requirements for the Powerware 9395−825/650, 9395−825/750, and 9395−825/825

– Common Battery

	Units				Rating 50/60 Hz
Basic Unit Rating
	kVA	650	650	750	750	825	825
	kW	585	591	675	682	7742	750
Input and Output Voltage	Volts	400/400	480/480	400/400	480/480	400/400	480/480
AC Input to UPS Rectifier (0.98 Minimum pF)

Full load current plus battery recharge current

(3) Phases, (1) Ground

Amps 1079 891 1245 1028 1369 1130

A

Minimum Conductor Size		AWG or kcmil	500	500	500	500	500	500
Number per Phase		(each)	(4)	(3)	(4)	(4)	(5)	(4)
AC Input to UPS Bypass (Four Wire)
Full Load Current		Amps	938	782	1083	902	1191	992
(3) Phases, (1) Ground	B
Minimum Conductor Size		AWG or kcmil	500	350	500	500	500	500
Number per Phase		(each)	(3)	(3)	(4)	(3)	(4)	(4)

AC Input to UPS Bypass (Five Wire)

Full Load Current

(3) Phases, (1) Neutral, (1) Ground

Amps 938 782 1083 902 1191 992

B

Minimum Conductor Size		AWG or kcmil	400	500	500	500	500	500
Number per Phase		(each)	(4)	(3)	(5)	(4)	(5)	(5)
DC Input from Battery Disconnect to UPS		Total Amps	1280	1280	1502	1502	1600	1600
(1) Positive, (1) Negative
	C
Minimum Conductor Size		AWG or kcmil	350	350	500	500	500	500
Number per Pole		(each)	(6)	(6)	(6)	(6)	(6)	(6)
AC Output to Critical Load (Four Wire)
Full Load Current		Amps	938	782	1083	902	1191	992
(3) Phases, (1) Ground	D
Minimum Conductor Size		AWG or kcmil	500	350	500	500	500	500
Number per Phase		(each)	(3)	(3)	(4)	(3)	(4)	(4)

AC Output to Critical Load (Five Wire)

Full Load Current

(3) Phases, (1) Neutral, (1) Ground

Amps 938 782 1083 902 1191 992

D

Minimum Conductor Size		AWG or kcmil	400	500	500	500	500	500
Number per Phase		(each)	(4)	(3)	(5)	(4)	(5)	(5)
Neutral Bonding Jumper (Four Wire Output Only)
Minimum Conductor Size	–	AWG or kcmil	4/0	4/0	4/0	4/0	4/0	4/0
Number		(each)	(1	(1)	(1	(1)	(1	(1)

NOTE Callout letters A, B, C, and D map to Figure 6-5, Figure 6-7, Figure 6-9,or Figure 6-11starting on page 6−8.

EATON Powerware® 9395 UPS (650–825 kVA) Installation and Operation Manual S 164201725 Rev 2 www.powerware.com 3−9