Schneider Electric HRB1684301-01 user manual Basic setup menu tree, Basic setup parameters, 3VT

Chapter 3—Front panel display and meter setup PowerLogic™ PM5500 series user manual

Basic setup menu tree

Maint	Reset
	Setup	Meter	Basic	Adv	Dmd	Tariff

1.Navigate to Maint > Setup.

2.Enter the setup password (default is “0”), then press OK.

3.Navigate to Meter > Basic.

4.Move the cursor to point to the parameter you want to modify, then press Edit.

5.Modify the parameter as required, then press OK.

6.Move the cursor to point to the next parameter you want to modify, press Edit, make your changes, then press OK.

Basic setup parameters

Parameter	Values	Description
	Select the power system type (power transformer) the meter is wired to.
	1PH2W LN	Single-phase 2-wire line-to-neutral
	1PH2W LL	Single-phase 2-wire line-to-line
	1PH3W LL with N	Single-phase 3-wire line-to-line with neutral
	3PH3W Dlt Ungnd	3-phase 3-wire ungrounded delta
	3PH3W Dlt Crnr Gnd	3-phase 3-wire corner grounded delta
Power System	3PH3W Wye Ungnd	3-phase 3-wire ungrounded wye
	3PH3W Wye Gnd	3-phase 3-wire grounded wye
	3PH3W Wye Res Gnd	3-phase 3-wire resistance-grounded wye
	3PH4W Opn Dlt Ctr Tp	3-phase 4-wire center-tapped open delta
	3PH4W Dlt Ctr Tp	3-phase 4-wire center-tapped delta
	3PH4W Wye Ungnd	3-phase 4-wire ungrounded wye
	3PH4W Wye Gnd	3-phase 4-wire grounded wye
	3PH4W Wye Res Gnd	3-phase 4-wire resistance-grounded wye
	Select how many voltage transformers (VT) are connected to the electrical power
	system.
VT Connect	Direct Con	Direct connect; no VTs used
	2VT	2 voltage transformers
	3VT	3 voltage transformers
VT Primary (V)	1 to 1,000,000	Enter the size of the VT primary, in Volts.
VT Secondary (V)	100, 110, 115, 120	Select the size of the VT secondary, in Volts.
	Define how many current transformers (CT) are connected to the meter, and
	which terminals they are connected to.
	I1	1 CT connected to I1 terminal
	I2	1 CT connected to I2 terminal
CT on Terminal	I3	1 CT connected to I3 terminal
	I1 I2	2 CT connected to I1, I2 terminals
	I1 I3	2 CT connected to I1, I3 terminals
	I2 I3	2 CT connected to I2, I3 terminals
	I1 I2 I3	3 CT connected to I1, I2, I3 terminals
	I1 I2 I3 IN	4 CT connected to I1, I2, I3, IN terminals
CT Primary (A)	1 to 1000000	Enter the size of the CT primary, in Amps.
CT Secondary (A)	1, 5	Select the size of the CT secondary, in Amps.
		This parameter displays when CT on Terminal is
CT Primary Neu. (A)	1 to 32767	set to I1,I2,I3, IN. Enter the size of the 4th (Neutral)
		CT primary, in Amps.
		This parameter displays when CT on Terminal is
CT Sec. Neu. (A)	1, 5	set to I1,I2,I3, IN. Select the size of the 4th
		(Neutral) CT secondary, in Amps.

36 HRB1684301-01