
Grey Headline (continued)
Subzones
TANDBERG VIDEO COMMUNICATIONS SERVER ADMINISTRATOR GUIDE
Applying Bandwidth Limitations to Subzones
Types of Limitations
You can apply bandwidth limits to the Default Subzone, Traversal Subzone and all manually configured subzones. The types of limitations you can apply vary depending on the type of subzone, as follows:
Limitation | Description | Can be applied to |
Total | Limits the total concurrent bandwidth being | • Default Subzone |
| used by all endpoints in the subzone at | • Traversal Subzone |
| any one time. In the case of the Traversal | |
| • Manually configured subzones | |
| Subzone, this is the maximum bandwidth | |
| available for all concurrent traversal calls. |
|
Calls | Limits the bandwidth of any individual call | • Default Subzone |
entirely | between two endpoints within the subzone. | • Manually configured subzones |
within... |
| |
|
| |
Calls into | Limits the bandwidth of any individual call | • Default Subzone |
our out of... | between an endpoint in the subzone, and an | • Manually configured subzones |
| endpoint in another subzone or zone. | |
|
| |
Calls | The maximum bandwidth available to any | • Traversal Subzone |
handled | individual traversal call. |
|
by... |
|
|
For all these settings, a bandwidth mode of:
•NoBandwidth will mean that no bandwidth is allocated and therefore no calls can be made.
•Limited will mean that limits are applied. You must also enter a value in the corresponding bandwidth (kbps) field.
•Unlimited will mean that no restrictions will be applied to the amount of bandwidth being used.
Use subzone bandwidth limits if you want to configure the bandwidth available between one
specific subzone and all other subzones or zones.
Use Pipes if you want to configure the bandwidth available between one specific subzone and another specific subzone or zone.
If your bandwidth configuration is such that multiple types of bandwidth restrictions are placed on a call (for example, if there are both subzone bandwidth limits and pipe limits), the lowest limit will always apply to that call.
How Different Bandwidth Limitations are Managed
In situations where there are differing bandwidth limitations applied to the same link, the lower limit will always be the one used when routing the call and taking bandwidth limitations into account.
For example, Subzone A may have a per call inter bandwidth of 128. This means that any calls between Subzone A and any other subzone or zone will be limited to 128kbps. However, Subzone A also has a link configured between it and Subzone B. This link uses a pipe with a limit of 512kbps. In this situation, the lower limit of 128kbps will apply to calls between the two, regardless of the larger capacity of the pipe.
In the reverse situation, where Subzone A has a per call inter bandwidth limit of 512kbps and a link to Subzone B with a pipe of 128, any calls between the two subzones will still be limited to 128kbps.
A
that subzone the amount of bandwidth of that call. A traversal call between two endpoints within the same subzone must, like all traversal call, pass through the Traversal Subzone.
This means that such calls will consume an amount of bandwidth from the originating subzone’s total concurrent allocation that is equal to twice the bandwidth of the call – once for the call from the subzone to the Traversal Subzone, and again for the call from the Traversal Subzone back to the originating subzone.
In addition, since this call passes through the Traversal Subzone, it will consume an amount of bandwidth from the Traversal Subzone equal to that of the call.
Introduction | Getting Started |
| Overview and |
| System |
| VCS |
| Zones and |
| Call | Bandwidth | Firewall |
| Maintenance |
| Appendices |
| Status |
| Configuration |
| Configuration |
| Neighbors |
| Processing | Control | Traversal |
|
| ||||
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
D14049.03 |
|
|
|
|
|
|
|
| 135 |
|
|
|
|
|
| ||
MAY 2008 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|