| Chapter 19 System Commands | |
Table 44 sys Commands (continued) |
|
|
COMMAND | DESCRIPTION |
|
sys tripleplay igmpsnp | Displays or sets the maximum response time for a IGMP membership |
|
maxresptime [tenthsofasecond] | query in tenths of a second. |
|
| This is used to determine the total group timeout value. |
|
| IGMP Group Timeout = (Robustness x Query Interval) + (Max |
|
| Response Time/10) + Time Value.(default = 2). |
|
|
|
|
sys tripleplay igmpsnp | Displays or sets the IGMP query interval time in seconds. |
|
queryinterval [seconds] | This is used to determine the query timeout value. |
|
| IGMP Query Timeout = (Robustness x Query Interval) + (Max |
|
| Response Time/20) + Time Value (default = 2). |
|
|
|
|
sys tripleplay igmpsnp robust | Displays or sets the level of robustness. |
|
[robustness] | robustness: This variable represents the level of expected packet |
|
| loss on the subnet. The range is |
|
| This is used to determine the leave timeout: |
|
| IGMP Leave Timeout = Robustness x Max Response Time/100 + 3 |
|
|
|
|
sys tripleplay portbase disable | Disables |
|
sys tripleplay portbase display | Displays the permanent virtual circuit (PVC) to port mappings for |
|
| tripleplay services such VoIP or video. |
|
sys tripleplay portbase enable | Enables |
|
sys tripleplay portbase groupadd | Adds ports and/or interfaces to a group mapping policy. |
|
[groupid][LAN[ports]][PVC[ports] |
|
|
][WLAN[ssid]] |
|
|
sys tripleplay portbase groupdel | Deletes the whole group or individual members. |
|
[groupid][LAN[ports]][PVC[ports] |
|
|
][WLAN[ssid]] |
|
|
sys tripleplay portbase groupset | Sets a group port to PVC mapping policy, with up to eight PVCs |
|
[groupid][LAN[ports]][PVC[ports] | allowed. WLAN may only belong to one group. |
|
][WLAN[ssid]] | If a product supports multiple SSID, each one will be treated as if it |
|
| were a port. |
|
sys tripleplay portbase save | Saves the port mappings to |
|
sys tripleplay portbase set | Sets a single port to single PVC mapping policy. |
|
<port><pvciddisable> | pvcid: The number of the PVC, between |
|
sys upnp active [0:no1:yes] | Activates or deactivates the saved UPnP settings. |
|
sys upnp config | Allows users to make configuration changes through UPnP. |
|
[0:deny1:permit] |
|
|
sys upnp display | Displays the UPnP configuration. |
|
sys upnp firewall | Allows UPnP to pass through the firewall. |
|
[0:deny1:pass] |
|
|
sys upnp load | Loads the UPnP setting buffer. Use this command to be able to |
|
| configure the settings. Use sys upnp save after you configure the |
|
| settings. |
|
sys upnp reserve | Retains UPnP created NAT rules even after restarting. |
|
[0:deny1:permit] |
|
|
sys upnp save | Saves the UPnP settings to the long term memory. |
|
sys userPassword <password> | Changes the user password. |
|
| This command may not be supported in your ZyXEL Device. |
|
|
|
|
sys version | Displays the firmware and bootbase versions. |
|
| 127 |
DSL & IAD CLI Reference Guide | |
|
|