Network | Carrier Access CMG Router specs

Profile Directory:Remote Profile

Filter Network/Server

NOTE: The server type 0004 was selected to be advertised to the LAN, therefore all 0004 type servers will be advertised and do not need to be individually selected (lines 2 through 4).

If the server type and name are specified, only servers that match both values will be learned or filtered. Be aware that the Name value is case and spacing sensitive.

Network

This field displays the network address of each service/network learned from the remote unit. If this route was added using the Static Network screen, “Static Fltr” will appear before the network address of this entry.

Type

This field is only available when the Setup field is set to <IPX Servers>. The Type field displays the Hex value assigned to each known server. When a service is added using [CTRL A], a Hex value must be defined. If you wish to learn or filter certain services that match a particular server type, manually add an entry specifying the desired Hex value. This setting will enable the unit to learn or filter all services that match the specified service type. This field may be used in conjunction with the Name field, described below. Range 1-FFFF.

5-36	CMG Router - Release 2.7

Image 168

Carrier Access CMG Router user manual Network

Contents

CMG Router Supporting Software Version Warranty Warranty Procedure Preface Limitation of Warranty & Limitation of Remedies Warranty Product Returns Vii Viii CMG Router Release Table of Contents Management Window Profile DirectoryRouter Card Profile Profile DirectoryLocal Profile Profile DirectoryRemote Profile Basic Configuration Verification WindowStatistics Window System Reports Window Router Configuration Exit WindowUser Events Troubleshooting Protocol TypesGlossary Index Chapter Installation Install a Router CardInstall Country Specific Ringer Tones Overview Maneuvering in the System Fields Scroll FieldSelect Field Edit Field Help Bar Connecting to the Router Establish a Telnet Session Set a New Password Introduction Management Window Management Overview System Time/Login Level Config allows the user to view and change all screens Users, as well as change all three passwordsSystem Date and Time Level Auto-Logout Timer View PasswordConfig Password Admin Password Enhanced Security When Telneting into the Router the following will appear Upload/Download To Setup the Router for Uploads/Downloads Management Window Upload/Download Setup Menu Fields Reboot After Load Code Config Upload/Download Load Defaults Software Images Choices Management Window Profile DirectoryRouter Card Profile Configuration Main Menu Select Router Card Setup and select Enter RIP Mode Receive RIP Mode SendSelection is RIP1, RIP2, or RIP1/RIP2 Trunk WAN Trunk Setup Menu Fields WAN Link #WAN Connection WAN Connection Type Multilink GroupData Speed Voice BW Limit % Select Security Configure and select Enter Security Security Setup Menu Fields Authentication by RemoteProtocol CHAP, PAP or None User ID Authentication of Remote PasswordLocal Security Server Type Snmp Snmp Setup Menu Fields SYS NameSYS Contact SYS Location Access Snmp Trap Destinations Location Select DNS Proxy Configure and select Enter DNS Proxy DNS Proxy Setup Menu Fields Domain NameDNS Server Site Select Spanning Tree Protocol Configure and select Enter Spanning Tree Protocol Bridge Forward Delay Bridge Hello TimeBridge Max Age Bridge Priority Select Network Time Protocol Configure and select Enter Network Time Protocol SPACEBAR, select Enter Network Time Protocol Setup Menu Fields SysLog SysLog Setup Menu Fields Sys LogFacility Level Select DNS Resolver Configure and select Enter DNS Resolver DNS Resolver Cache Contents DNS ResolverMy Domain Name My Node Name Static Host List View or Modify Quality of Service Select Quality of Service Configure and select Enter Quality of Service Menu Fields Routed Voice Priority TOS Mgcp Mgcp Setup Menu Fields Mgcp Interoperability Settings Mgcp Interoperability Menu Fields Mgcp Keep-Alive Timeout Mgcp Type of ServiceQuarantine Notification Handling Quarantine Event Handling Voice Algorithm Names Voice Algorithm Name Fields Algorithm IDAlgorithm Definition Algorithm Alias VoIP VoIP Setup Fields Call Detail Record Voice Algorithm Settings T38 Fax Voice Algorithm Settings VoIP Algorithm Fields Select Voice Channels Configure and select Enter Voice Channels VoIP Setup Fields Profile DirectoryRouter Card Profile Signaling Type RFC2833 Options Signals Payload TypeRepeat Count Repeat Interval Select Dial Plan Configure and select Enter Dial Plan Dial Plan Menu Fields Short Inter DigitLong Inter Digit Profile DirectoryLocal Profile Main Menu Profile Directory window Local Profile window LAN Local Profile Setup To Setup a Local Profile Local Profile Setup Menu Fields Profile Setup for LocalUnitLAN Network Updates Protocol LAN Default Router IP AddressSubnet Mask Setup Static Networks Profile DirectoryLocal Profile To Setup Static Networks Select Configuration Profile Directory from the Main menu,Select LAN Setup and Enter Static Networks Fields Network Metric HopsTicks Next Gateway Static Addresses Static MAC Address Setup Setup Static Static Addresses FieldsDevice Name MAC Address To Define and Enable Filters FiltersSelect Define Filter Custom Select LAN Setup -and select Enter Forward Mode Filters FieldsDefine Filter Filter Type Source/Destination Filter Name Defining Custom Filters Select Define Filter Custom and Enter Defining Protocol Filters Defining Address Filters Advertise Network/Server Advertise Network Server Window Setup Advertise Network/Server FieldsSelected Items IPX Server Advertising Advertise Network/Server IPX Server Fields TypeName Dhcp Server/Client/Relay Dhcp Dhcp Mode Server Domain NameStart IP Address Number NetBIOS over TCP/IP Lease DurationDomain Name Servers Option Type Value Dhcp Mode Relay Forward DHCP/TOOTP Requests to Dhcp Mode Client Automatic DNSSet Tx Packets Broadcast Bit Request LAN Collision Threshold Collision Threshold Provisioning LAN Collision Threshold Fields To Configure Spanning Tree Spanning Tree Select Setup Spanning Tree and select Enter Spanning Tree Fields Port PriorityPort Cost Secondary IP Address To Add a Secondary IP Address Secondary IP Address Fields Link Speed To Set the Link Speed Link Speed Fields Profile DirectoryLocal Profile Profile DirectoryRemote Profile LocalUnit LAN Setup Profile DirectoryRemote Profile Remote Profile window Remote WAN Profile Profile Setup for RemoteUnit Transmission Options ModeProtocol Route Blocked Bridge Optimize WAN Network Updates GRE Tunnel Enabled with GRE Tunnel Disabled Enabled with GRE Tunnel By NetworkNAT Gateway Enabled with GRE Tunnel All Tunnel NameRemote IP Tunnel Address Encryption Algorithm Default Router Numbered Setup bottom of the Remote main window Security/Options Following Security/Options setup window will display Security/Options Fields Security ServerCompression Typical Data Static/VPN Networks Profile DirectoryRemote Profile Select WAN Setup -on the RemoteUnit line and press Enter VPN Features Static/VPN Networks FieldsGRE Tunnel Encrypt Tunnel data ? Encryption Algorithm not supported in this release Static NAT Addresses Local IP Address NAT IP Address NAT Bypass Subnets Press Ctrl a to add a NAT Bypass Static Addresses Static Addresses Window MAC Address Static Addresses Window IP Address Symbol Description Firewall Filters To Add a Firewall Filter Select Ctrl a to add an IP Firewall Rule Firewall Filters Fields Rule NumberAction Pass/Drop Service Service EstablishmentName Description Local IP Address/Network Remote IP Address/NetworkPackets which match this rule Significant Bits Filter Network/Server Filter Network /Server Filter Network/Server Fields Selected Items Filter/Learn Network Filter Learn To Configure Spanning Tree Select Setup Spanning Tree and select Enter Port Priority Trunk Port WAN Connection Type PPP in Frame Relay, or Frame Relay ML QOS InterleavingML Fragment Threshold Basic Configuration Start Basic Configuration Select Yes to enter the setup program and select Enter Router Identification Fields Directions for LAN Network Updates RIP mode to be received from remotesRIP mode to send to remotes Protocol remotes will use to authenticate local LocalUnit Authentication User ID Protocol LocalUnit will use to authenticate all remotesChange the PAP Secret LocalUnit will send? WAN Interface Connections Port Number For Frame Relay, Set Option for PVC Management Link Quality Monitoring SensitivitySet Poll Interval Set Poll Counter Remote Adit Profile Profile NameOther Select WAN Port Number Subnet MaskConnection WAN Connection Type Snmp Configuration Snmp CommunitiesStatistics Averaging Interval Setup Complete Verification Window Ping Utility Access Port LAN Port Tests FieldsDst Host Src IP Address Response Window Fields Single PingContinuous Ping Timeout Count Result or Last ResultResponse Count Trace Route Trace Route Utility Start Tracert DstHostSrc Port SrcIP Port Timeout MethodSize IP Tos Port Monitor Port Name Start MonitorTrap On Number of bytes to display for each packet Verification Window Verification Window Statistics Window Run-Time Auto-Update Run-Time FieldsClear Totals Press ENTER. The Run-time Statistics window will display Errors LAN Packet TotalsWAN Packet Totals Received Remote’s Name Forwarded to WANThroughput to/from WAN Comp. Ratio to/from WAN VoIP Channel View VoIP Channel View Fields SlotCall Agent Endpoint Prefix Rsip Status Field Value Meaning Type Meaning Priority Queue Priority Queue Fields Clear AllPriority Fields Priority Traffic Type Statistics Window System Reports Window Events To View the Event Log Events Fields TimeMessage Count Alarms Alarms Fields Networks/Servers Networks/Servers Fields DisplayLearned From Press ENTER. The Networks/Servers listing will display Frame Type Address Tables Address Tables Fields Flush Learned Entries Displays the information, listing by Port System Reports Window Exit Window Logout Reinitialize 10-4 Router Configuration Basic Setup Command Description Basic VoIP Setup Overview Set the controller to use CLI commands Command Description Fax and Modem Setup Following will configure the Fax and Modem CMG Router Release 11-7 Select Voip Configure -and select Enter Tab to Voice Algorithm Settings and select Enter 11-10 CMG Router Release 11-11 Card Maximum # of Channels configured for T.38 Reserved CMG Router Release 11-13 PPP Internet Connection and Public IP Address Routing Router in Slot CMG Router Release 11-15 Back-to-Back with PPP Boulder Router in Slot Denver Router in Slot Back-to-Back with Multi-Link PPP CMG Router Release 11-19 Back-to-Back with Frame Relay CMG Router Release 11-21 11-22 Appendix a User Events Description Authenticate Events Triggered Events Alarms User Events Appendix B Protocol Number in Firewall Filters Number Keyword Protocol Reference LEAF-2 Tlsp Reference SRP Ethernet Protocol Types HEX AT&T 8047 Protocol Types Protocol Types KTI Appendix C Communication Related Issues LAN Related IssuesExcessive Triggered Update Events on the Events screen LAN Related Issues Unable to access the Local LAN Router unit via Telnet Unable to access a remote unit via Telnet Diagnostics and Performance Tools Verification Ping Utility Statistics Run-Time System Reports Events Identify Alarm State Description Display Alarms Clear Alarm Troubleshooting Algorithm Annex DBandwidth Bit Challenge Handshake Authorization Protocol Chap Command LineBridge Ethernet FirewallFrame Frame relay Host InternetProtocol IP Local Area Network LAN Loopback Media Access Control MAC Mbps Multilink PPP Ping Protocol Point-to-Point Protocol PPPQoS Rsip Spanning Tree Protocol Telnet Trace Route Trunk Voice over IP VoIP Index Index CMG Router Release Index Snap RIP IPX Index SYS Index Index