Manuals / Brands / Computer Equipment / Network Router / Cisco Systems / Computer Equipment / Network Router

Cisco Systems IPMUX-1, IPMUX-1E Bundle Connection Configuration: Static Mode

1 217

Download 217 pages, 3.45 Mb

IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus

Connection Configuration: Static Mode E-29

Bundle Connection Configuration: Static Mode

BUNDLE CONNECTION CONFIGURATION

1. Bundle ID 1

2. IP TOS 1

3. TDM Bytes in Frame (x48 bytes) 1

4. Connection Status Disable

5. Destination IP Address 0.0.0.0

6. Next Hop 0.0.0.0

7. Destination Bundle 1

8. Jitter Buffer (x10 µsec) rounded up 1000 µsec steps! 300

9. OAM Connectivity Disable

A. Redundancy Function None

B. VLAN Tagging Yes

C. VLAN ID 1

E. VLAN Priority 00

ESC. Exit

Calculated bundle throughput [BPS]: 3978080

Select item from the menu.

Figure E-32. Bundle Connection Configuration (Static Mode)

Parameters must be configured for each connection. To configure all parameters,

first select the bundle ID and then proceed with the parameter configuration.

• First define the bundle.

• When changing the Destination IP Address, Next Hop, or Destination Bundle,

the Connection Status must be set to Disable. After you save the changes,

Connection Status can be reset to Enable.

Table E-20. Bundle Connection Parameters: Static Mode

Parameter Possible Values Remarks

Bundle ID 1, 2 If only one bundle is used, the Bundle ID must be

configured as 1.

IP ToS 0 to 255 Type of Service – sets the IP ToS field in the IP

frames transmitted by the device.

ToS configuration configures the WHOLE byte, since

different vendors may use different bits to tag

packets for traffic prioritization.

ToS assignment applies to all TDM packets leaving

IPmux-1.

Default configuration: 0

VLAN ID and

VLAN Priority are

configurable only if

VLAN Tagging is

set to Yes.

Main Menu

↓

2. Configuration

↓

3. Connection

Configuration

↓

2. Bundle

Connection

Configuration

Note

Contents

Main Page IPmux-1, IPmux-1E TDMoIP Gateways Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Attention Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Declaration of Conformity Preface Foreword Manual Organization Conventions Page IPmux-1, IPmux-1E TDMoIP Gateways Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Attention Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Declaration of Conformity Preface Foreword Manual Organization Conventions Quick Start Guide 1. Setting Jumpers - IPmux-1E ISDN Version Only 2. IPmux-1/1E Operation 3. IPmux-1/1E Configuration General Configuration Contents List of Figures Page List of Tables Chapter 1 Introduction 1.1 Overview Versions Options Applications IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Overview 1-3 Figure 1-2. E1/T1 Circuit Extension over an IP/Ethernet Network Figure 1-3. Analog Voice Application Chapter 1 Introduction IPmux-1/1E Installation and Operation Manual 1-4 Overview Figure 1-4. Digital ISDN Application (V5.1 Concentration of Remote BRIs) Figure 1-5. Extending ISDN BRI Ports of a Small Office Features Management T1 E1 ISDN BRI FXS/FXO/E&M IP Ethernet Ports TDMoIP Operation Modes QoS Timing 1.2 Physical Description Front Panel Rear Panel 1.3 Functional Description Operation Modes Static Mode Dynamic CAS Mode CESoIP Mode E1/T1 ISDN BRI FXS/FXO/E&M Timeslot Assignment in a Bundle ISDN BRI FXS/FXO/E&M Testing Timing Modes E1/T1 ISDN/FXS/FXO/E&M Network Timing Schemes External Network Timing IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Functional Description 1-15 Figure 1-12. IPmux-1 in External Clock Mode Single Source Clock Network Figure 1-13. IPmux-1 in Adaptive Timing Mode Figure 1-14. IPmux-1E in Adaptive Timing Mode Megaplex can also be connected directly to the network, via its TDMoIP main link (ML-IP). Frame Format Page VLAN Support UDP Support Packet Delay Variation PDVT (Jitter) Buffer PDVT Buffer Effect on Delay Intrinsic PDV in Static Mode Intrinsic PDV in Dynamic CAS Mode Intrinsic PDV in CESoIP Mode Ethernet Throughput Ethernet Throughput in Static Mode Ethernet Throughput in Dynamic CAS Mode Ethernet Throughput in CESoIP Mode Round Trip Delay Round Trip Delay in Static Mode Round Trip Delay in Dynamic CAS Mode Packet Delay in CESoIP Mode Reorder and Duplication of Ethernet Frames Static Mode Dynamic CAS Mode CESoIP Mode OAM Connectivity End-to-End Alarm Generation VLAN Traffic Behavior Ethernet User Port Internal Switch Operation Modes Page Page Page Page Page DHCP Lease Length Manager Option 1.4 Technical Specifications E1 Port E1 Framing T1 Port T1 Framing Local Terminal and Control Interface Ethernet Analog Voice Page Page Power Physical Page Chapter 2 Installation 2.1 Introduction 2.2 Site Requirements and Prerequisites 2.3 Package Contents Power Cord 2.4 Equipment Needed 2.5 Installation and Setup Setting Jumpers IPmux-1 IPmux-1E Page Connecting Interfaces and Cables Grounding Fuses Location of Connectors Table 2-3. Control Port Pinout Table 2-4. ISDN-S-Interface Pin Assignments Connecting the Control Port Connecting the Power AC Power Connection DC Power Connection Page Chapter 3 Operation 3.1 Front Panel Controls, Connectors, and Indicators 2 3 Figure 3-1. IPmux-1 Front Panel LEDs Figure 3-2. IPmux-1 Rear Panel Switch Table 3-1. IPmux-1 System Indicators and Switches Table 3-1. IPmux-1 System Indicators and Switches (Cont.) Figure 3-3. IPmux-1E Front Panel Indicators 3.2 Operating Instructions Turning IPmux-1/1E On Without Control Terminal With Control Terminal Login User Name and Password Turning IPmux-1/1E Off 3.3 Getting Started 3.4 Overview of Menu Operations Navigating IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Figure 3-5. IPmux-1 (E1/T1) Terminal Menu Tree Overview of Menu Operations 3-7 Chapter 3 Operation IPmux-1/1E Installation and Operation Manual Figure 3-6. IPmux-1E ISDN-S Terminal Menu Tree 3-8 Overview of Menu Operations IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Overview of Menu Operations 3-9 Figure 3-7. IPmux-1E FXS/FXO/E&M Terminal Menu Tree Chapter 3 Operation IPmux-1/1E Installation and Operation Manual 3-10 Overview of Menu Operations Figure 3-8. IPmux-1/1E Connection Configuration Menu Tree for Static Mode IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Overview of Menu Operations 3-11 Figure 3-9. IPmux-1E Connection Configuration Menu Tree for Dynamic CAS Mode Main Menu System Menu Setting IPmux-1/1E Configuration Options Figure 3-14. IPmux-1E ISDN-S Configuration Menu Specific parameters are explained in Appendix E. Performance Monitoring Page Chapter 4 Troubleshooting and Diagnostics 4.1 Error Detection Using Front Panel LEDs Working with the Alarm Buffer Table 4-1. Event Types Table 4-1. Event Types (Cont.) * 1 sec / 1 min. For further information see Logfile Events in Appendix E. 4.2 Troubleshooting 4.3 Performance Monitoring and Troubleshooting Statistics E1/T1 Statistics Page Page Table 4-3. E1/T1 Alarms Page Page Page LAN Statistics One Ethernet Port Figure 4-2. LAN Statistics Page Table 4-4. LAN Statistics Parameters Table 4-4. LAN Statistics Parameters (Cont.) With User Ethernet Port Page Table 4-5. LAN Statistics Parameters Table 4-5. LAN Statistics Parameters (Cont.) Bundle Connection Statistics Table 4-6. Bundle Connection Status Parameters Page Page Page 4.4 Diagnostic Tests E1/T1 External Loop Internal Loop ISDN BRI External Loop Internal Loop FXS/FXO/E&M Remote Loopback 4.5 Frequently Asked Questions Page Page Page Appendix A Boot Sequence for Downloading Software A.1 General A.2 Booting IPmux-1/1E General Boot Sequence Accessing the File System Page Page Appendix B Telnet B.1 General B.2 Using Telnet to Manage the IPmux-1/1E Starting a Telnet Session Telnet Operation System Security Page Page Appendix C SNMP Management C.1 SNMP Environment SNMP Principles SNMP Operations Management Information Base (MIB) MIB Structure MIBs Supported by the IPmux-1/1E SNMP Agent Management Domains under SNMP SNMP Communities Authentication Network Management Stations Appendix D TFTP Download Procedures D.1 Inband TFTP Download Procedure Preliminary Procedure Checking the Download Page Appendix E Configuration Menus E.1 Main Menu E.2 Viewing the IPmux-1/1E System General Information Figure E-3. General Information Window ISDN Figure E-4. General Information Window FXS Self-Test Results Figure E-5. Last Self-Test Results Window Table E-1. Last Self-Test Results Parameters Reset System Event Log Logfile Events Ping Figure E-9. Ping Dialog Box E.3 General Configuration General Configuration Menu Figure E-10. General Configuration Menu Host IP Default Gateway DHCP Status Management Configuration Figure E-12. Management Configuration Authentication/Community Figure E-13. Authentication/Community Menu Manager List Table E-4. Manager List Parameters Alarm Traps Mask Figure E-15. Alarm Traps Mask Menu Table E-5. Alarm Traps Mask Parameters Table E-6. IPmux-1/1E Alarms The other alarms are not used. Telnet Access ASCII Terminal Configuration Figure E-16. ASCII Terminal Configuration Menu Table E-7. ASCII Terminal Configuration Parameters Time/Date Update Figure E-17. Time/Date Update Menu Table E-8. Time/Date Update Parameters Download/Upload Using Xmodem TFTP Figure E-19. Download/Upload Using TFTP Window Page Set Default Parameters E.4 IPmux-1 E1/T1 Configuration E1 Configuration Figure E-24. E1 Physical Layer Configuration Menu Table E-12. E1 Physical Layer Configuration Parameters Table E-12. E1 Physical Layer Configuration Parameters (Cont.) Table E-12. E1 Physical Layer Configuration Parameters (Cont.) T1 Configuration Figure E-25. T1 Physical Layer Configuration Menu Table E-13. T1 Configuration Parameters Page Page Table E-13. T1 Configuration Parameters (Cont.) E.5 IPmux-1E Configuration Figure E-26. ISDN Configuration Menu ISDN Configuration Table E-14. ISDN Configuration ISDN Channel Configuration Figure E-27. ISDN Channel Configuration Menu Table E-15. ISDN Channel Parameters Analog Configuration Figure E-28. Analog Configuration Menu Table E-16. Analog Configuration Analog Channel Configuration Figure E-29. Channel Configuration Menu Table E-17. Analog Configuration Signaling Profile Configuration E.6 Connection Configuration: Static Mode Bundle Connection Configuration: Static Mode Table E-20. Bundle Connection Parameters: Static Mode Table E-20. Bundle Connection Parameters: Static Mode (Cont.) Protection Switching Configuration E.7 Connection Configuration: Dynamic CAS Mode Bundle Connection Configuration: Dynamic CAS Mode Table E-22. Bundle Connection Parameters: Dynamic CAS Mode Table E-22. Bundle Connection Parameters: Dynamic CAS Mode (Cont.) Activation Criterion Figure E-36. Activation Criterion Menu Table E-23. Activation Criterion Parameters E.8 Connection Configuration: CESoIP Mode Bundle Connection Configuration: CESoIP Mode Table E-24. Bundle Connection Parameters: CESoIP Mode Table E-24. Bundle Connection Parameters: CESoIP Mode (Cont.) E.9 LAN Configuration (No User Port) When configuring two LANs, see Ethernet Configuration/Status . Figure E-39. LAN Configuration Menu Page E.10 DS0 Bundle Configuration Figure E-40. DS0 Bundle Configuration Menu Table E-26. DS0 Bundle Configuration Parameters E.11 Performance Monitoring E1/T1 Statistics Table E-27. E1/T1 Statistics Parameters Table E-27. E1/T1 Statistics (Cont.) ISDN Statistics in IPmux-1 Figure E-42. ISDN Statistics Menu Table E-29. ISDN Statistics Parameters Press N. Analog Status IPmux-1E with FXS/FXO/E&M LAN Status (no User port) Figure E-44. LAN Status Menu LAN statistics are not collected in intervals. Type R. Table E-30. LAN Status Table E-30. LAN Status (Cont.) Bundle Connection Status /Statistics Figure E-45. Bundle Connection Statistics Menu Figure E-46. Bundle Connection Status Menu Type R. Table E-31. Bundle Connection Status/Statistics Parameters E.12 Ethernet Configuration/Status with Ethernet User Port General Information Figure E-47. General Information Window Two Ethernet Ports Aging Time Figure E-48. Switch Configuration Two Ethernet Ports LAN Configuration Figure E-49. LAN Configuration Two Ethernet Ports See Internal Switch Operation Modes in Chapter 1. Table E-32. LAN Configuration Two Ethernet Ports Erase MAC Table VLAN Configuration LAN Status Press N. Page Table E-35. LAN Status Two Ethernet Ports Page Index Page Page Page Page Page DC Power Supply Connection Terminal Block Connector Note: Ignore this supplement if the unit is AC-powered. Preparing and Connecting the Power Supply Cable with the TB Plug + - ( ) Page Page Customer Response Form Page Error Report