Environmental | Cisco Systems SOFTWARE RELEASE 2.5 manual

Chapter 2 Preparing to Install the CiscoWorks 1130 Wireless LAN Solution Engine

Preparing Your Site for Installation

Preparing Your Site for Installation

This section describes the requirements your site must meet for safe installation and operation of your WLSE. Ensure that your site is properly prepared before beginning installation.

Environmental

When planning your site layout and equipment locations, keep in mind the precautions described in this section to help avoid equipment failures and reduce the possibility of environmentally caused shutdowns. If you are currently experiencing shutdowns or unusually high errors with your existing equipment, these precautions will help you isolate the cause of failures and prevent future problems.

Use the following precautions when planning the operating environment for your WLSE.

•Always follow the ESD-prevention procedures described in the Preventing EMI, page 2-8to avoid damage to equipment. Damage from static discharge can cause immediate or intermittent equipment failure.

•Make sure that the chassis cover is secure. The chassis is designed to allow cooling air to flow effectively within it. An open chassis allows air leaks, which could interrupt and redirect the flow of cooling air from internal components.

•Electrical equipment generates heat. Ambient air temperature might not be adequate to cool equipment to acceptable operating temperatures without adequate circulation. Make sure that the room in which you operate has adequate air circulation.

Choosing a Site for Installation

Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location. Statement 1017

	Installation and Configuration Guide for the CiscoWorks Wireless LAN Solution Engine
78-15903-01	2-9

Image 45

Cisco Systems SOFTWARE RELEASE 2.5 Preparing Your Site for Installation, Environmental, Choosing a Site for Installation

Contents

Corporate Headquarters Copyright 2003, Cisco Systems, Inc. All rights reserved Iii N T E N T S Network Options Verifying the Configuration Upgrade Versions Vii Cisco 90-Day Limited Hardware Warranty Terms Replacement, Repair, or Refund Policy for Hardware Duration of Hardware WarrantyTo Receive a Return Materials Authorization RMA Number Viii Cisco 90-Day Limited Hardware Warranty Terms Page Preface Conventions AudienceConvention Xii Bewaar Deze Instructies Waarschuwing Belangrijke Veiligheidsinstructies Varoitus Tärkeitä Turvallisuusohjeita Warnung Wichtige SicherheitshinweiseXiv Aviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla Sicurezza Xvi Varning! Viktiga Säkerhetsanvisningar Xvii Xviii Product Documentation Xix Document Title Description Obtaining Documentation Cisco.comDocumentation CD-ROM Obtaining Technical Assistance Ordering DocumentationDocumentation Feedback Cisco TAC Website Opening a TAC Case TAC Case Priority DefinitionsXxii Obtaining Additional Publications and Information Xxiv Supplemental License Agreement Installation and Use Software Upgrades, Major and Minor Releases Reproduction and DistributionXxvi Product Overview Software Features Bezel Features Bezel Features Front Panel Features Front Panel Features System Indicators and Buttons Indicator or Button Color Function Back Panel Features Serial Port Parameter Setting Pin Signal Definition Ethernet Connectors Network Cable Requirements Equipment Included in the Package 78-15903-01 Product Overview Equipment Included in the Package Safety Safety Säilytä Nämä Ohjeet Conservare Queste Istruzioni Guarde Estas Instrucciones General Precautions Maintaining Safety with Electricity Preventing EMI Protecting Against Electrostatic Discharge Preparing Your Site for Installation Choosing a Site for InstallationEnvironmental Grounding the System Creating a Safe Environment AC Power Cabling Precautions for Rack-Mounting 78-15903-01 Tools and Equipment Required for Installation 78-15903-01 Installation Quick Reference Installing the CiscoWorks Wireless LAN Solution Engine Installing the Wireless LAN Solution Engine in a Rack Installing the CiscoWorks 1130 Wireless LAN Solution Engine Installing the CiscoWorks 1130 Wireless LAN Solution Engine Rack Depth inches Front Adapter Part Number 91695 94089 Mounting bracket Push button Reinstall the front bezel Connecting Cables Connecting the Wlse to the AC Power Source Powering On the Wlse Next Steps-Configuration 78-15903-01 Task Steps References Configuration Quick Reference Logging into the Web Running the Setup Program Configuring the WLSE’s Network Information Prompt Response Description Configuring the Wlse Without a DNS Server Mailroute hostname ip-address Prompt Response Description Sample Response Configuring Name Resolution Changing the Configuration After Running SetupConfiguring the Wlse Without a DNS Server No ip name-server ip-address Verifying the Configuration # ping ip-address # nslookup dns-name Configuring the Web Browser Supported BrowsersClient Operating System Supported Browsers Select Enable for Scripting of Java applets Configuring Internet ExplorerSelect Tools Internet Options Security Select Tools Internet Options Privacy Configuring Netscape Navigator Select Enable all cookiesSelect Edit Preferences Wlse Next Steps-Finish Initial Configuration Setting Up Device Management Logging into the Web Interface and Verifying ConnectivityHttp//209.165.202.1281741 Set Up Non-IOS Access Points and Wireless Bridges Setting Up DevicesTasks Procedure Cisco Discovery Protocol New User Set Up IOS Access Points Click SecurityClick User Manager About Configuration for WDS About Configuration for VLANs Ip ssh time-out Ip ssh authentication-retries Select Services Telnet/SSH Enable Secure Shell Set Up IOS Access Points by Using the Web Interface Select Services Telnet/SSH Click Read-OnlyClick Read-Write Task Procedure Set Up Routers and SwitchesMode and use the set snmp community read-only Use the snmp community communitystring ro Set location-set system location location Set Up AAA Servers Adding AAA Servers to the WLSE, Adding Device Credentials to the Wlse Enter Http Credentials for Non-IOS Access Points Select Devices Discover Device Credentials Snmp Communities Enter Snmp Community Strings for All Managed Devices Enter Http Port Settings for IOS Access Points Enter Telnet or SSH Credentials for IOS Access Points Select Devices Discover Device Credentials Wlccp Credentials Enter Wlccp Credentials for Wireless Domain Services WDS Adding AAA Servers to the Wlse Select Devices Discover AAA ServerText Box Description Discovering and Managing Devices Configuring Discovery OptionsTask Reference Select Devices Discover Discover Advanced Options Run CDP Discovery Discovering Devices Run CDP Discovery Now Modify the CDP Discovery Schedule Select Devices Discover DiscoverSelect Modify Periodic and click Next Import Devices from a File Import Devices Import Devices from a CiscoWorks Server Select Devices Discover Managing Devices Adding Users Select Administration User Admin Manage Users Next Steps Configuring the CiscoWorks 1105 and 1130 Wlse Next Steps Installing Software on CiscoWorks 1105 and 1130 Wlse Upgrade Versions Downloading the Upgrade ImageBacking Up the Wlse Upgrade Methods Upgrading by Using the Web Interface Upgrade Quick ReferenceInstalling from the Local Repository Field Data to Enter Select Administration Appliance Software Define Repository Subst f d\WLSErepository Installing from a Windows Server Appliance Software Status View Log Upgrading by Using the CLI Create a Local Repository Create the Repository Create a Repository on a Windows Server Install Install the Software Related CLI Commands At the following prompt, enter yes Upgrading from the Recovery CD Do you wish to continue Yes/No/Rescue yes 78-15903-01 Component Specifications Technical Specifications for CiscoWorks 1130 Wlse Component Specifications IN-1 D E IN-2 CDP IN-3 Http IN-4 IN-5 Snmp IN-6