Control Logic Signal Specifications
Control Logic Signal Specifications
The control logic connectors are located just behind the front housing cover. The relay contacts are just to the left of the logic connectors. Connector labeling is shown below.
Logic inputs
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| AL2 |
| AL1 | AL0 |
|
|
|
| L | 6 |
| 5 | 4 | 3 | 2 |
| 1 | PCS |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| Relay |
| Analog |
| Analog |
| Logic | |||||||||||
| contacts |
|
|
| |||||||||||||||
|
| inputs |
| output | outputs | ||||||||||||||
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
H O OI L AM CM2 12 11
Specifications for the logic connection terminals are in the following table:
|
| Terminal Name | Description | Ratings |
|
|
|
|
|
|
|
|
|
|
|
| [PCS] | +24V for logic inputs | 24VDC, 30 mA max. (do not short to terminal L) |
|
|
|
|
|
|
| [1], [2], [3], [4], [5], | Discrete logic inputs | 27VDC max. (use PCS or an external supply refer- |
|
| [6] |
| enced to terminal L) |
|
|
|
|
|
|
| [L] (top row) *1 | GND for logic inputs | sum of input |
|
|
|
|
|
|
| [11], [12] | Discrete logic outputs | 50mA maximum ON state current, |
|
|
|
| 27 VDC maximum OFF state voltage |
|
|
|
|
|
|
| [CM2] | GND for logic outputs | 100 mA: sum of 11 and 12 currents (return) |
|
|
|
|
|
|
| [AM] | Analog voltage output | 0 to 10VDC, 1mA maximum |
Operations Monitoringand |
|
|
|
|
| [L] (bottom row) *2 | GND for analog signals | sum of OI, O, H, and AM currents (return) | |
|
| |||
|
|
|
|
|
|
| [OI] | Analog input, current | 4 to 19.6 mA range, 20 mA nominal, |
|
|
|
| input impedance 250 Ω |
|
|
|
|
|
|
| [O] | Analog input, voltage | 0 to 9.8 VDC range, 10VDC nominal, |
|
|
|
| input impedance 10 kΩ |
|
|
|
|
|
|
| [H] | +10V analog reference | 10VDC nominal, 10 mA max |
|
|
|
|
|
|
| [AL0] | Relay common contact | 250 VAC, 2.5A (R load) max., |
|
|
|
| 250 VAC, 0.2A (I load, P.F.=0.4) max. |
|
| [AL1] *3 | Relay contact, normally open | |
|
| 100 VAC, 10mA min. | ||
|
| [AL2] *3 | Relay contact, normally | 30 VDC, 3.0A (R load) max. |
|
|
| closed | 30 VDC, 0.7A (I load, P.F.=0.4) max. |
|
|
|
| 5 VDC, 100mA min. |
|
|
|
|
|
Note 1: The two terminals [L] are electrically connected together inside the inverter.
Note 2: We recommend using the top row [L] logic GND for logic input circuits and the [L] GND on the bottom row of terminals for analog I/O circuits.
Note 3: Default relay N.O./N.C. configuration is reversed. See page