EX- FCCS

Data Programming

<Node which uses CCIS Trunk via Fusion Link (PC1 and PC2 in the example)>

STEP 1: ASYD

Assign the Point Code to all the nodes in the network uniquely as described on Page 163.

STEP 2: ADPCL

Assign the destination PC (Point Code) on LGRT (for speech path) number basis for all the nodes in the network.

STEP 3: ACSCL

Assign the location of the CCH and FPC of the node which accommodates CCIS trunk in CSCG (Common Channel Signaling Controller Group) for all the nodes in the network.

Assign the location of the CCH using the ACSC command. The following is sample data assignment. In this sample, PC 3 is equipped with three DTI cards. Note that if the system employs one CCIS link, enter the same data in CSCG130 and CSCG131.

CSCG

MG

U

G

CICG

 

 

 

 

 

 

AA

A

AA

0

 

 

 

 

 

 

BB

B

BB

1

 

 

 

 

 

130

BB

B

BB

2

 

 

 

 

BB

B

BB

3

(Basic/

Primary

BB

B

BB

4

Route)

 

 

 

 

BB

B

BB

5

 

 

 

 

 

 

 

BB

B

BB

6

 

 

 

 

 

 

BB

B

BB

7

 

 

 

 

 

CCH 0

CCH 1

CSCG

MG

U

G

CICG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CC

C

CC

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CC

C

CC

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CC

C

CC

2

 

 

 

 

 

 

131

 

 

 

 

 

 

 

 

 

 

CC

C

CC

3

 

 

 

 

 

 

(Alternate

 

 

 

 

 

CCH 2

 

 

 

 

 

 

 

 

 

CC

C

CC

4

 

Route)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CC

C

CC

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CC

C

CC

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CC

C

CC

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note 1: In the case of actual data entry, enter corresponding LEN numbers instead of letters such as “AAAAA”.

Note 2: Refer to Figure 8-8Port Allocation and Related Command for CCIS Trunk”.

STEP 4: ACIC1

Assign CSCG for Basic/Primary Route. The odd numbered CSCG for alternate Route assignment.

PC

CSCG

 

 

4

130

 

 

<Network Control Node (PC1 in the example)>

STEP 1: ALRTN

Assign the Logical Route Numbers to all external trunks used in the EX-FCCS network. Assign unique Logical Route Numbers to the whole routes for external trunks on the network (including COT, DAT, Dummy route, etc.) using this command. The data must be set at the NCN in each Fusion Group and is to be set for every external route in all the nodes.

STEP 2: ARSCN

Assign route restriction information according to the Route Restriction Class (RSC) of the Logical Route Number in the network.

CHAPTER 8

ND-70185 (E)

Page 190

Revision 3.0

Page 205
Image 205
NEC NEAX2400 system manual Adpcl, Acscl, Network Control Node PC1 in the example, Alrtn