NEC NEAX2400 system manual Sample Data Assignment Acrd

DATA PROGRAMMING

Assignment of FCH Related Data

STEP 1: ACRD

Assign Route Class Data of Speech Route, FCH, FGH routes, respectively. A sample data assignment is shown below.

PBXspeech

	RT1
	DTI
		signaling
Nail
	￿
Down	FGH
	RT14
Connection		Q-sig
	FCH

RT13

to CPU

T1

ROUTER

		Type		Speech	FCCH	FGH
	CDN		RT	1	13	14
	1		TF	3	3	3
	2		TCL	4	4	4
	3		RLP	2	2	2
	4		SMDR	0	0	0
	5		LSG	12	13	13
	6		PAD
	7		TRKS	0(1)	0	0
	8		TC/EC
	9		FINT	0	0	0
	10		FPEG	0	0	0
	11		TC	0	0	0
￿	12		MTC	0	0	0
	13	STSEQ		0	0	0
	14		FGH	0	0	1
	15		MMN
	16		LKIND	2	0	0

Note: This data setting is an example.

Figure 5-51 Sample Data Assignment (ACRD)

STEP 2: ACTK

Assign the connection trunk data of DTI, FCH, and FGH cards, using the ACTK command. When assigning FCH, FGH trunk data, eight trunks must be set. A sample data assignment of FCH, FGH card is as follows.

When FCH and FGH cards are mounted in the following slots with the specified RT numbers, data setteing is as follows:

				FCH(RT13)													FGH(RT14)
PWR	PWR									LV7								FCH(RT13)
		slot05								LV0				slot21
							15	19	23						15	19	23
		03 01	05	07	09	11				01	03	05	07	09	11
PWR	PWR	02 00	04	06	08	10	14 13 12	18 17 16	22 21 20	00	02	04	06	14 13 12 10 08		18 17 16	22 21 20	FGH(RT14)
		slot05												slot21

	C_RT			C_TK				C_LENS
			MG					U	G		L
(1-1023)				(1-4095)
						00-07			0-3	00-23		0-7
		1	3		1	0	0		0	0	3	0
		1	3		2	0	0		0	0	3	1
		1	3		3	0	0		0	0	3	2
		1	3		4	0	0		0	0	3	3
		1	3		5	0	0		0	0	3	4
		1	3		6	0	0		0	0	3	5
		1	3		7	0	0		0	0	3	6
		1	3		8	0	0		0	0	3	7
		1	4		1	0	0		1	1	5	0
		1	4		2	0	0		1	1	5	1
		1	4		3	0	0		1	1	5	2
		1	4		4	0	0		1	1	5	3
		1	4		5	0	0		1	1	5	4
		1	4		6	0	0		1	1	5	5
		1	4		7	0	0		1	1	5	6
		1	4		8	0	0		1	1	5	7

Figure 5-52 Sample Data Assignment (ACTK)

ND-70185 (E)CHAPTER 5

Page 105

Revision 3.0