Support Software Capabilities

 

 

 

 

 

Section 4-1

 

 

 

 

 

 

 

 

 

 

 

 

 

Function code

Mnemonic

Function code

 

Mnemonic

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

17

 

 

ASFT

64

 

SPED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

TKY

65

 

PULS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

19

 

 

MCMP

66

 

SCL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

47

 

 

RXD

67

 

BCNT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

48

 

 

TXD

68

 

BCMP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

60

 

 

CMPL

69

 

STIM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

61

 

 

INI

87

 

DSW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

62

 

 

PRV

88

 

7SEG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

63

 

 

CTBL

89

 

INT

 

 

Online Editing

 

If unsupported addresses are set in the program for operands or set values,

 

 

error messages will be displayed and the values will not be accepted.

4-1-3 Offline Operations

 

 

 

 

 

 

 

 

 

The following operations are possible when not connected online to the PC.

 

 

 

 

 

 

 

 

 

Group

Name

 

 

 

Description

 

 

 

 

 

 

 

 

 

Programming

Connect line

Draws a line between two ladder diagram objects.

 

 

 

 

 

 

 

 

Save program

Writes all or part of the user program developed in the system work area to the

 

 

 

data disk.

 

 

 

 

 

 

 

 

 

 

 

Retrieve program

Retrieves all or part of the user program stored on a data disk to the system

 

 

 

work area.

 

 

 

 

 

 

 

 

 

 

 

 

 

Change display

Specifies the display modes for the user program.

 

 

 

 

 

 

 

 

Search

Searches for instructions including specified operands. An address from which

 

 

 

the search is to be started can be specified

 

 

 

 

 

 

 

 

I/O comment

Creates I/O comments corresponding to bit addresses in the Ladder With

 

 

 

Comments mode. In addition, reads (searches) and edits the program for

 

 

 

comments.

 

 

 

 

 

 

 

 

 

 

 

Instr comment

Creates and edits instruction comments for output instructions in the Ladder

 

 

 

With Comments mode. (C-series PCs only)

 

 

 

 

 

 

 

 

Block comment

Creates, reads (searches), and edits block comment in the Ladder With

 

 

 

Comments mode.

 

 

 

 

 

 

 

 

 

 

 

 

Edit ladder

Edits ladder diagrams using the following:

 

 

 

 

 

 

Moving specified instruction blocks

 

 

 

 

 

 

Copying specified instruction blocks

 

 

 

 

 

 

Deleting specified instruction blocks

 

 

 

 

 

 

 

 

Edit comments

Displays I/O comments simultaneously to write, edit, and search for specified

 

 

 

comments.

 

 

 

 

 

 

 

 

 

 

 

Retrieve

Retrieves comments from the program stored on a data disk. The I/O comments

 

comments

are read to the system work area. Instruction comments (C-series PCs only)

 

 

 

and block comments are copied to the currently displayed program.

 

 

 

 

 

Memory usage

Displays the used capacity of the user program memory, the number of

 

 

 

comments used, and the available capacity of the internal memory.

 

 

 

 

 

Clear memory

Clears the user program memory. The starting address for clearing can be

 

 

 

specified. The comment memory can also be cleared.

 

 

 

 

 

Check program

Checks whether the user program contains syntax errors. The check can be

 

 

 

performed in three levels.

 

 

 

 

 

69

Page 81
Image 81
Omron CPM1A operation manual Offline Operations, Online Editing