Installing the CPM1A, 1 CPM1A Orientation, Correct | Omron specification

Installing the CPM1A	Section 3-3

3-3 Installing the CPM1A

3-3-1 CPM1A Orientation

The CPM1A must be installed in the position shown below to ensure adequate cooling.

Correct

Do not install the CPM1A in either of the following positions.

Incorrect

Incorrect

3-3-2 CPM1A Installation

	The CPM1A can be installed on a horizontal surface or on a DIN track.
Surface Installation	Use the following pattern when installing a CPM1A on a horizontal surface.
	CPM1A-10CDR-j/10CDT-D/10CDT1-D and
	CPM1A-20CDR-j/20CDT-D/20CDT1-D

Two, M4 holes
100 mm CPU Unit
A	8 mm

Use M4 dia. x 15 screws.

The width (A) between the mounting holes depends on the CPM1A model.

Model number	Width (A)

CPM1A-10CDR-j/10CDT-D/10CDT1-D CPU Unit	56 mm

CPM1A-20CDR-j/20CDT-D/20CDT1-D CPU Unit	76 mm

Allow 10 to 15 mm between the Units when installing a Communications Adapter next to the CPU Unit, as shown below.

	21 mm
81 mm	CPU Unit 100 mm

Communications

Adapter10 to 15 mm

39

Image 52

Omron operation manual Installing the CPM1A, 1 CPM1A Orientation, 2 CPM1A Installation, Correct, Incorrect

Contents

CPM1A CPM1A Programmable Controllers Omron Product References  Omron Table of Contents Appendices About this Manual Precautions Safety Precautions General PrecautionsIntended Audience Operating Environment Precautions Application Precautions Xiv Application Precautions Backup method Data EC Directives Applicable DirectivesConcepts Conformance to EC Directives Xviii Section 1 CPM1A Features CPM1A Features and FunctionsSection Using the PT NT Link Communications CompoBus/S I/O Link UnitsStandard Peripheral Devices Programming is Possible 2 I/O Terminal and IR Bit Allocation CPU UnitsExpansion I/O Units Unit Relay output Transistor output Sink type Source type 3 CPM1A Functions Control Corresponding IR word Setting range BCDSet value Word Word 001 or later PC model Input bits Response time Mode Function PC model Input bits Min. input pulse width Pulse output single-phase output Temperature Sensor Unit Functions CompoBus/S Slave Functions CPM1A-SRT21 System Configuration CPU Unit and Expansion I/O Unit ConfigurationCPU Unit and Expansion Unit CPM1A CPU Units Expansion I/O Units Unit Max. number Inputs Outputs Model Units Host Link Communications Expansion Units Connecting to a Programmable Terminal Adapters and Cables One-to-one PC Link CommunicationsName Usage Model number Name Specifications One-to-one NT Link CommunicationsCompoBus/S I/O Link Connections Peripheral Device Connections Sysmac Support Software SYSMAC-CPT Support Name Model number Revised Specifications Previous specifications New specifications Relevant pages Unit Specifications and Components General Specifications SpecificationsCPM1A-10CDR-j CPM1A-20CDR-j CPM1A-30CDR-j CPM1A-40CDR-j Characteristics Memory Backup 3 I/O Specifications CPU Unit Input SpecificationsIncrement Mode 5 kHz Max Specification Expansion I/O Unit Input Specifications CPU Unit and Expansion I/O Unit Output Specifications Relay Output Transistor Output Sink Type Transistor Output Source Type20EDT 8ET 10CDT1-D 20CDT1-D 30CDT1-D 40CDT1-D 20EDT1 8ET1 RS-232C Adapter Specifications Communications Adapter SpecificationsRS-422 Adapter Specifications Unit Components CPU Unit ComponentsCPM1A-10CDR-j/10CDT-D/10CDT1-D 10 I/O Terminals CPM1A-40CDR-j/40CDT-D/40CDT1-D 40 I/O Terminals Fatal error Input indicators Indicator Status MeaningCPU Unit Component Descriptions Expansion I/O Unit Components Expansion I/O Unit with 20 I/O TerminalsExpansion I/O Unit with 8 Input Terminals Expansion I/O Unit with 8 Output Terminals Temperature Sensor Unit Components Analog I/O Unit Components CPM1A-TS001/002 CPM1A-TS101/102Set value Thermocouple Range C Range F Set value Platinum resistance Range C Range F Pins Function CompoBus/S I/O Link Unit Components RS-232C Adapter Communications Adapter ComponentsRS-422 Adapter Installation and Wiring Design Precautions Power Supply WiringPower Supply Voltage 4 CPM1A Power Interruptions Selecting an Installation Site Installation Site ConditionsMomentary Power Failure Detection Automatic Restart Panel/Cabinet Installation Overheating Installing the CPM1A 2 CPM1A Installation1 CPM1A Orientation Correct DIN Track Installation Installation Connecting an Expansion I/O UnitRemoval Section Wiring and Connections General Precautions for WiringLine Noise Hanging Ducts Ground Wiring Floor DuctsConduits Grounding Crimp Connectors To 240-VAC Power Supply VDC Power Supply Input Wiring Input Configuration CPM1A-8ED Input Wiring Example Outputs Device Circuit diagram Input Devices Inductive Loads Output Wiring Relay Output Wiring Output Configurations CPM1A-8ER Transistor Output Wiring Sink Type CPM1A-8ET Transistor Output Wiring Source Type CPM1A-40CDT1-D Polarity of Power Supply for the Load Output Short Protection Inrush Current Considerations Fuse Insertion Host Link Connections Peripheral Device ConnectionOne-to-one Host Link Connection One-to-N Host Link Connection RDB SDB RDA SDA One-to-one PC Link Connections One-to-one NT Link Connections C200HX/HG/HE PC Using Peripheral Devices 2 CPM1A Restrictions and Precautions SSS System SetupSupport Software Capabilities Offline Operations Online Editing Group Name Description Go To CopyFill Print File Time Chart PC SetupGroup Name Description Utility Data Area Lists Change Online Operations Offline and Online Operations Using a Programming Console Compatible Programming ConsolesCQM1-PRO01-E C200H-PRO27-E Mode Switch Buzzer VolumeDifferent Keys Contrast Control Changing the CPM1A’s Mode with the Mode Switch Program ModeMonitor Mode RUN Mode Connecting the Programming Console Panel Installation Entering the Password Preparation for Operation Program Password Program BZ Programming Console Operations Overview All Clear Clearing MemoryPartial Clear Buzzer Operation Reading/Clearing Error MessagesKey Sequence OFF Entering or Editing Programs Writing Hexadecimal, BCD Constant Writing a Word Address #FFF6 Writing an Unsigned Decimal NumberWriting a Word Address DM Instruction Search Bit Operand Search Inserting and Deleting Instructions Insertion00207INSERT END Not Deletion Checking the Program Delete END00178CIRCUIT ERR Corrected Program 11 Bit, Digit, Word Monitor Bit MonitorCont Word Monitor Channel LR Multiple Address MonitoringCLR Channel LR Differentiation Monitor Binary Monitor@OFF OFF OFF CLR OFF OFF OFF Three-word Monitor Signed Decimal Monitor Unsigned Decimal Monitor Three-word Data Modification Changing Timer, Counter SV3CH CHG? Inputting a New SV Constant Hexadecimal, BCD Data ModificationIncrementing and Decrementing a Constant Pres VAL? Binary Data ModificationMontr Signed Decimal Data Modification D0000 Montr Force Set, Reset Unsigned Decimal Data Modification Clear Force Set/Reset Hex-ASCII Display ChangeOn on 00000FORCE RELE? Program Password Programming ExampleDisplaying the Cycle Time Preparatory Operations 00000MEMORY CLR? HR CNT DM Montr END HR CNT DM Programming Procedures Example Program Programming Procedures Inputting the One-second TimerInputting the Self-holding Bit Write NOP Inputting the Two-second Timer Inputting the 10-count Counter Inputting the Flicker Output LD notInputting the END001 Instruction Test Run in Monitor Mode Monitor BZ Test Runs and Error Processing Initial System Checks and Test Run Procedure 2 CPM1A Test Run ProcedureInitial System Checks Points to check Flash Memory Precautions Error CPM1A Cycle Non-fatal Errors Fatal ErrorsSelf-diagnosis Functions Message FAL No Meaning and appropriate response Identifying Errors User-defined ErrorsError Messages Error Flags Programming Console Operation Errors Programming ErrorsFALS07 Message MSG46 Type Message Meaning and appropriate response Circuit ERR Troubleshooting Flowcharts Main Check Power Supply Check Fatal Error Check Follow the Memory Error Non-fatal Error Check 121 122 Environmental Conditions Check Memory Error Check Maintenance Inspections Power supply Allowable voltage fluctuation rangeInspection Items Inspection items Details Criteria Remarks Handling Precautions Necessary Tools for InspectionStandard Tools Measurement Devices Expansion Memory Unit Precautions OverviewMemory Areas Button Specifications Specifications and NomenclatureNomenclature LED Indicator HandlingMounting/Removing Eeprom Mounting Eeprom Peripheral Port Communications Settings PC ConnectionsCPM1, CPM1A, CPM2A CQM1, and SRM1 PCs Disconnecting Uploading Programs Operation Procedure Downloading Programs 134 135 Standard Models Expansion UnitsCPU Units Expansion I/O Units Temperature Sensor Units Description Specifications Model numberCompoBus/S I/O Link Unit Communications Adapters Name Appearance Model Number Specifications Peripheral Devices Dimensions CPM1A-10CDR-j/10CDT-D/10CDT1-D CPU UnitCPM1A-20CDR-j/20CDT-D/20CDT1-D CPU Unit CPM1A-30CDR-j/30CDT-D/30CDT1-D CPU Unit CPM1A-20EDjExpansion I/O Unit CPM1A-40CDR-j/40CDT-D/40CDT1-D CPU UnitCPM1A-8jjjExpansion I/O Unit CPM1A-MAD01 Analog I/O Unit CPM1A-TSjjjTemperature Sensor UnitCPM1A-SRT21 CompoBus/S I/O Link Unit CPM1-CIF01 RS-232C Adapter CPM1-CIF11 RS-422 Adapter Dimensions with Peripheral Devices Attached Appendix B ACP AsciiAUTOEXEC.BAT BCD Bit designator Bit numberBit-control instruction Block CONFIG.SYS CTS Default DIP switchData link Data link area Eeprom Eprom FCS Delay Initialization errorInput signal Install JIS LED LSS Not OFF PCB RAM PromRAS ROM SCP SSS Syntax error System configurationSystem error System error message WDT Numbers Index 165 166 167 Revision code Date Revised content Revision History